LAISHA
Open Laisha

Wisconsin Master Cheesemaker Program

USA · Center for Dairy Research, University of Wisconsin–Madison, with the Wisconsin Master Cheesemaker Board

19practice questions written to this syllabus
2subjects

What Wisconsin Master Cheesemaker Program is

Wisconsin Master Cheesemaker Program is a specialist certification exam run by Center for Dairy Research, University of Wisconsin–Madison, with the Wisconsin Master Cheesemaker Board, for candidates in USA.

Format

Certification by cheese variety over about 2 years 8 months: required short courses, then assessment of the candidate's cheese and knowledge.

Sections

How it has changed

Applicants must currently make cheese in a Wisconsin plant, have held a Wisconsin cheesemaker's licence for at least 10 years, and have made the variety for at least 5 years; they must first complete an Advanced Cheese Technology short course and one elective. CDR calls it the only such programme in the U.S. Page read 3 Oct 2026.

How to prepare for Wisconsin Master Cheesemaker Program

Where our 19 questions for it fall

Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.

  1. Heaviest (95% of the questions): Cheese Science & Technology (18).

    Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.

  2. Middle band: Sensory Evaluation & Judging of Dairy Products (1).

    One pass per subject, then mixed sets across them.

  3. Hardest share: Cheese Science & Technology (4 hard of 18).

    Leave untimed time for these and read every explanation, including for the options you rejected.

Official source: cdr.wisc.edu

8 practice questions, worked

Original questions written to this exam's published syllabus and pattern. Not past papers.

1. 1,000 kg of milk with 3.6% fat gives 99 kg of cheese containing 33.5% fat. What is the fat recovery?

  1. 92.1%
  2. 93.1%
  3. 7.9%
  4. 9.9%
Answer and working

A. 92.1%

Fat in cheese = 99 × 0.335 = 33.17 kg; fat in milk = 36 kg; recovery = 33.17 ÷ 36 × 100 = 92.1%. 93.1% divides the two fat percentages (scaled), ignoring masses; 9.9% is the yield; 7.9% is the fat lost to whey.

Cheese Science & Technology · Cheese yield: formulas and factors

2. Why is the temperature raised slowly at the start of cooking?

  1. To make sure all lactose is fermented before the whey is drained
  2. To prevent the starter bacteria from producing acid too early
  3. To avoid case hardening, which traps whey inside the curd
  4. To keep the coagulant active until the curd is fully drained off
Answer and working

C. To avoid case hardening, which traps whey inside the curd

Rapid heating case-hardens the particle surface, sealing in moisture. Slow cooking is not about keeping the coagulant active or delaying acid.

Cheese Science & Technology · Cutting, cooking and syneresis

3. Irregular mechanical openings in a cheese that should be close-textured result from:

  1. Late blowing by clostridia from silage spores in the milk
  2. Propionic fermentation
  3. Excessive proteolysis
  4. Poor knitting of curd particles
Answer and working

D. Poor knitting of curd particles

Mechanical openness arises in pressing; gas holes come from microbial gas.

Sensory Evaluation & Judging of Dairy Products · Body and texture defects

4. A vat yielded 9.80 kg of Cheddar per 100 kg milk at 36.5% moisture. Adjust this to the plant's reference moisture of 37% using adjusted yield = actual × (1 − actual W) ÷ (1 − reference W).

  1. 9.72 kg
  2. 9.93 kg
  3. 9.88 kg
  4. 10.30 kg
Answer and working

C. 9.88 kg

9.80 × 0.635 ÷ 0.630 = 9.88: drier cheese is credited upward. 9.72 inverts the ratio; 9.93 uses moisture fractions instead of dry fractions; 10.30 adds the 0.5-point moisture difference directly to the yield.

Cheese Science & Technology · Cheese yield: formulas and factors

5. A Cheddar shows many small gas holes and a spongy body within the first few days. The most likely cause is:

  1. Early gas from coliforms or yeasts: poor hygiene or slow acid
  2. Calcium lactate crystallisation from racemisation by NSLAB bacteria
  3. Late gas from clostridial spores, pointing to silage feeding of cows
  4. Eye formation by propionibacteria added accidentally with the starter
Answer and working

A. Early gas from coliforms or yeasts: poor hygiene or slow acid

Early blowing appears within days and is caused by coliforms or yeasts. Clostridial late blowing appears after weeks; calcium lactate gives crystals, not holes.

Cheese Science & Technology · Cheese defects and grading

6. What is the function of a block-forming tower in a Cheddar plant?

  1. Separating cream from milk before the milk is pumped to the vats
  2. Fusing salted curd under vacuum into blocks of uniform weight
  3. Brining Gouda wheels by moving them through a tall column of brine
  4. Stretching curd in hot water to align protein fibres for pizza cheese
Answer and working

B. Fusing salted curd under vacuum into blocks of uniform weight

Towers take milled, salted curd and form uniform blocks under vacuum. Cooker-stretchers handle pasta filata; separators skim milk.

Cheese Science & Technology · Mechanised and UF-based cheese making

7. Milled Cheddar curd (900 kg) is dry-salted at 2.5% of curd weight; 40% of the added salt is lost in the press whey and the pressed cheese weighs 860 kg. What is the salt content of the cheese?

  1. 1.05%
  2. 1.57%
  3. 1.50%
  4. 2.62%
Answer and working

B. 1.57%

Added = 22.5 kg; retained = 22.5 × 0.6 = 13.5 kg; salt = 13.5 ÷ 860 × 100 = 1.57%. 2.62% ignores the loss; 1.50% uses the curd mass instead of the cheese mass; 1.05% keeps the lost fraction instead of the retained one.

Cheese Science & Technology · Salting: dry, brine and its effect

8. A Cheddar maker drains whey at a lower pH than usual. What change in the cheese is expected?

  1. Less calcium and more retained coagulant: a softer, more crumbly body
  2. A higher pH in the final cheese because lactose drains with the whey
  3. More calcium and less coagulant, giving a firmer, more elastic body
  4. No change in texture, because pH only affects flavour development
Answer and working

A. Less calcium and more retained coagulant: a softer, more crumbly body

Lower draining pH dissolves more colloidal calcium phosphate into the whey and retains more coagulant in the curd, giving more acid, crumbly cheese. Draining pH is a key texture control.

Cheese Science & Technology · Cutting, cooking and syneresis

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock all 19 questions — Wisconsin Master Cheesemaker Program

US$10 a month · one price worldwide · cancel any time

  • Every practice question for this course, with explanations
  • Timed papers for the exams this course leads to
  • Ask Laisha to explain any topic — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.