LAISHA
Open Laisha

Irrigation Association Certified Irrigation Designer — Agriculture (CID)

USA · Irrigation Association

89practice questions written to this syllabus
5subjects

What Irrigation Association Certified Irrigation Designer is

Irrigation Association Certified Irrigation Designer — Agriculture (CID) is a professional certification run by Irrigation Association, for candidates in USA.

Format

General Ag exam (150 MCQs, 4 h) plus a specialty exam — Drip/Micro (75 questions, 4 h) or Sprinkler (50 questions, 4 h) — all within 3 years.

Sections

How it has changed

The clearest published content blueprint for irrigation design anywhere; useful to irrigation designers in any country.

How to prepare for Irrigation Association Certified Irrigation Designer

Where our 89 questions for it fall

Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.

  1. Heaviest (65% of the questions): Sprinkler & Micro-Irrigation Systems (37); Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) (21).

    Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.

  2. Middle band: Fluid Mechanics & Open Channel Hydraulics (14); Groundwater, Wells & Pumps (10).

    One pass per subject, then mixed sets across them.

  3. Lighter: Protected Cultivation & Greenhouse Engineering (7).

    Definitions, classifications and standard figures; quick to revise, easy marks to lose.

  4. Hardest share: Groundwater, Wells & Pumps (3 hard of 10), Protected Cultivation & Greenhouse Engineering (2 hard of 7), Sprinkler & Micro-Irrigation Systems (10 hard of 37).

    Leave untimed time for these and read every explanation, including for the options you rejected.

Official source: irrigation.org

8 practice questions, worked

Original questions written to this exam's published syllabus and pattern. Not past papers.

1. Why are media filters installed as two or more tanks in parallel?

  1. So one tank can be backflushed with water filtered by the others while the system runs
  2. Because a single tank usually cannot hold enough sand media to filter the full system design flow
  3. To double the filtration fineness
  4. Because regulations forbid single tanks
Answer and working

A. So one tank can be backflushed with water filtered by the others while the system runs

Backflushing reverses flow through one tank using clean water from the others; this keeps unfiltered water out of the system and allows continuous operation.

Sprinkler & Micro-Irrigation Systems · Filtration

2. A fertiliser (bypass) tank is fully mixed, so the concentration leaving it falls exponentially, C = C₀e^(−V/Vt), where V is the water passed and Vt the tank volume. What share of the original fertiliser remains after three tank volumes have passed?

  1. 25%
  2. 0%
  3. 5%
  4. 33%
Answer and working

C. 5%

Remaining fraction = e⁻³ = 0.050, about 5%. A linear assumption would give 0% after one volume; 25% and 33% have no basis. This exponential decay is why bypass tanks give non-uniform application and need about four tank volumes to empty.

Protected Cultivation & Greenhouse Engineering · Micro-irrigation and fertigation in greenhouses

3. An irrigation must apply at least 80 mm to the driest quarter of a field. The system's low-quarter DU is 0.80. What average depth must be infiltrated?

  1. 144 mm
  2. 80 mm
  3. 100 mm
  4. 64 mm
Answer and working

C. 100 mm

Average = required low-quarter depth / DU = 80 / 0.80 = 100 mm. 64 mm multiplies by DU; 80 mm assumes perfect uniformity; 144 mm adds 80 % of 80 to 80.

Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Irrigation efficiencies and distribution uniformity

4. A valve with loss coefficient K = 10 is fitted in a 100 mm pipe whose Darcy friction factor is 0.02. What equivalent length of straight pipe produces the same loss?

  1. 50 m
  2. 5 m
  3. 0.5 m
  4. 500 m
Answer and working

A. 50 m

Equate KV²/2g to f(L_e/D)V²/2g: L_e = KD/f = 10 × 0.1/0.02 = 50 m. Omitting the diameter gives K/f = 500 m; 5 m and 0.5 m are factor-of-ten slips in D or f.

Fluid Mechanics & Open Channel Hydraulics · Minor losses

5. Why should filter losses be taken at their 'dirty' (backflush trigger) value when computing the TDH for pump selection?

  1. Because clean filters have no loss
  2. Because dirty filters reduce the pump's NPSH required and so allow a higher suction lift
  3. Because filter loss is independent of flow, so the dirty value is the only one that can be measured
  4. Because the pump must still deliver the required pressure just before the filter is cleaned
Answer and working

D. Because the pump must still deliver the required pressure just before the filter is cleaned

Filter loss rises as it loads, up to the backflush set point. If the pump is selected with clean-filter loss, the critical block will be under-pressured for much of the time. Clean filters still have some loss, and the loss does depend on flow.

Sprinkler & Micro-Irrigation Systems · System layout and pump selection

6. Two identical centrifugal pumps are run in parallel on a friction-dominated pipeline. Compared with one pump alone, the system flow will be:

  1. Exactly double
  2. Unchanged
  3. More than one pump's flow but less than double
  4. Less than one pump's flow
Answer and working

C. More than one pump's flow but less than double

Parallel pumps add flow at a given head, but the system curve rises with Q², so the new operating point is at a higher head and each pump delivers less. The shortfall is largest for steep system curves.

Groundwater, Wells & Pumps · Centrifugal pump characteristic curves

7. An old iron main with Hazen-Williams C = 100 is replaced by a new plastic pipe of the same internal diameter with C = 140, carrying the same flow. By what factor does the new pipe's friction head loss differ from the old?

  1. It is 0.510 times the old loss
  2. It is 1.86 times the old loss
  3. It is 0.536 times the old loss
  4. It is 0.714 times the old loss
Answer and working

C. It is 0.536 times the old loss

h_f ∝ 1/C^1.852, so new/old = (100/140)^1.852 = 0.536. Taking the loss inversely proportional to C gives 0.714; to C² gives 0.510; 1.86 inverts the ratio.

Fluid Mechanics & Open Channel Hydraulics · Hazen-Williams equation

8. A 2-ft Parshall flume runs under free flow with Ha = 1.5 ft. Using Q = 4 W Ha^(1.522 W^0.026), what is the discharge?

  1. 15.0 ft³/s
  2. 12.0 ft³/s
  3. 7.5 ft³/s
  4. 22.0 ft³/s
Answer and working

A. 15.0 ft³/s

Exponent = 1.522 × 2^0.026 = 1.550; Q = 4 × 2 × 1.5^1.550 = 15.0 ft³/s. 7.5 omits W; 12.0 treats the relation as linear in Ha; 22.0 uses the V-notch exponent.

Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Water measurement: weirs, Parshall flume and orifices

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock all 89 questions — Irrigation Association Certified Irrigation Designer — Agriculture (CID)

US$10 a month · one price worldwide · cancel any time

  • Every practice question for this course, with explanations
  • Timed papers for the exams this course leads to
  • Ask Laisha to explain any topic — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.