LAISHA
Open Laisha

Irrigation Association Certified Irrigation Designer Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods): practice questions

Irrigation Association Certified Irrigation Designer — Agriculture (CID) · USA · Irrigation Association

Original practice questions written to the published syllabus · not past papers
10worked here, free
21written to this exam in this subject
9syllabus units

About Irrigation Association Certified Irrigation Designer

Irrigation Association Certified Irrigation Designer — Agriculture (CID) is a professional certification run by Irrigation Association, for candidates in USA. General Ag exam (150 MCQs, 4 h) plus a specialty exam — Drip/Micro (75 questions, 4 h) or Sprinkler (50 questions, 4 h) — all within 3 years.

Source: irrigation.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Irrigation Association Certified Irrigation Designer

How much water a crop needs, when to give it, how to measure and convey it, and how to design surface irrigation.

Our 21 Irrigation Association Certified Irrigation Designer questions in this subject: 3 easy, 13 medium, 5 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Irrigation Association Certified Irrigation Designer and are not shown on any other exam's page.

Question 1 · easy

A grower plans to let a field crop dry to a soil matric potential of about −300 kPa before irrigating. Which instrument is unsuitable for signalling that trigger point?

  1. Electrical resistance (gypsum) block
  2. Neutron probe calibrated for the soil
  3. Gravimetric sampling
  4. Tensiometer
Answer and working

D. Tensiometer

Tensiometers read matric potential only down to about −80 kPa; below that the water column breaks. Resistance blocks work in the drier range, and the neutron probe and gravimetric sampling measure water content, which can be related to potential through the retention curve.

Question 2 · medium

A manager keeps a field close to field capacity with frequent light irrigations throughout a rainy month. What is the likely effect on effective rainfall?

  1. It rises, because runoff is reduced on wet soil
  2. It rises, because wet soil has higher infiltration
  3. It falls, because there is little empty storage in the root zone to hold the rain
  4. It is unchanged, since effective rainfall depends only on rain intensity and not on soil storage
Answer and working

C. It falls, because there is little empty storage in the root zone to hold the rain

Rain can only be stored in the unfilled part of the root zone. A soil kept near field capacity sends most rain to runoff or deep percolation. Wet soils usually have lower, not higher, infiltration rates.

Question 3 · hard

A 2-ft Parshall flume runs under free flow with Ha = 1.5 ft. Using Q = 4 W Ha^(1.522 W^0.026), what is the discharge?

  1. 15.0 ft³/s
  2. 12.0 ft³/s
  3. 7.5 ft³/s
  4. 22.0 ft³/s
Answer and working

A. 15.0 ft³/s

Exponent = 1.522 × 2^0.026 = 1.550; Q = 4 × 2 × 1.5^1.550 = 15.0 ft³/s. 7.5 omits W; 12.0 treats the relation as linear in Ha; 22.0 uses the V-notch exponent.

Question 4 · medium

Design guidance for plastic irrigation pipelines (for example the USDA NRCS practice standard) commonly limits the design velocity to about 1.5 m/s (5 ft/s) unless surge protection is analysed. The main reason is to:

  1. Prevent sediment from settling in the pipe
  2. Increase friction loss deliberately so that all outlets are balanced
  3. Limit water hammer pressures on valve closure and pump start-stop
  4. Keep water temperature low
Answer and working

C. Limit water hammer pressures on valve closure and pump start-stop

Surge pressure is proportional to the velocity change, so a velocity limit caps the transient. Sediment settling is a concern at low, not high, velocities, and extra friction is not a design goal.

Question 5 · medium

Which is a real limitation of level basin irrigation?

  1. Dikes interfere with machinery, and waterlogging can damage sensitive crops on heavy soils
  2. It always produces large tailwater runoff, because basins are closed on only three of their four sides
  3. It usually cannot be used on clay soils
  4. It needs high-pressure pumps
Answer and working

A. Dikes interfere with machinery, and waterlogging can damage sensitive crops on heavy soils

Basins are closed, so runoff is minimal; they are well suited to clays; and they work by gravity at low head. The genuine drawbacks are dikes and temporary ponding.

Question 6 · easy

Surge irrigation in furrows means:

  1. Irrigating every other furrow
  2. Applying a large stream continuously until runoff begins, then stopping
  3. Pumping water under pressure through emitters in the furrow
  4. Applying water intermittently in on-off cycles to the same furrows
Answer and working

D. Applying water intermittently in on-off cycles to the same furrows

Surge flow alternates water between sets of furrows in cycles; the wetted, consolidated reach takes in less water in later surges, so advance is faster and more uniform on many soils. Alternate-furrow irrigation and drip are different techniques.

Question 7 · medium

A furrow-irrigated farm loses 25 % of applied water as tailwater. Which measure recovers most of that loss on the farm?

  1. A tailwater collection and reuse (pump-back) system
  2. Lengthening the set time
  3. Increasing the furrow stream (inflow rate)
  4. Reducing the furrow slope to zero and blocking the ends of all furrows on a sandy soil
Answer and working

A. A tailwater collection and reuse (pump-back) system

Collecting runoff in a sump or pond and pumping it back to the head recovers it. Larger streams and longer sets increase runoff; blocking furrow ends on sand can over-irrigate the tail and cause deep percolation.

Question 8 · medium

Infiltrated depths (mm) at eight equally spaced points are 22, 30, 26, 34, 18, 28, 32 and 30. What is the low-quarter distribution uniformity?

  1. 85.5 %
  2. 58.8 %
  3. 65.5 %
  4. 72.7 %
Answer and working

D. 72.7 %

Mean = 220 / 8 = 27.5 mm. The lowest quarter (2 of 8 values) is 18 and 22, mean 20 mm. DU = 20/27.5 = 72.7 %. 65.5 % uses only the minimum; 85.5 % averages the lowest half; 58.8 % divides by the maximum.

Question 9 · hard

For approximately normally distributed application depths, a system with low-quarter DU of 80 % has a Christiansen CU of about:

  1. 80.0 %
  2. 87.4 %
  3. 63.0 %
  4. 68.2 %
Answer and working

B. 87.4 %

CU ≈ 100 − 0.63 (100 − DU) = 100 − 0.63 × 20 = 87.4 %. 68.2 % applies the inverse relation (DU ≈ 100 − 1.59 (100 − CU)) in the wrong direction; CU is always higher than DU for the same data, so 80 % and 63 % are wrong.

Question 10 · medium

An irrigation must apply at least 80 mm to the driest quarter of a field. The system's low-quarter DU is 0.80. What average depth must be infiltrated?

  1. 144 mm
  2. 80 mm
  3. 100 mm
  4. 64 mm
Answer and working

C. 100 mm

Average = required low-quarter depth / DU = 80 / 0.80 = 100 mm. 64 mm multiplies by DU; 80 mm assumes perfect uniformity; 144 mm adds 80 % of 80 to 80.

A study plan for Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Irrigation Association Certified Irrigation Designer

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 21 questions): Irrigation efficiencies and distribution uniformity (4, 19%); Furrow irrigation (3, 14%); Irrigation scheduling (3, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Basin irrigation (2, 10%); Crop coefficients and crop water requirement (2, 10%); Soil-water-plant relations: field capacity, wilting point and MAD (2, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Underground pipeline systems (2, 10%); Water measurement: weirs, Parshall flume and orifices (2, 10%); Effective rainfall (1, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Basin irrigation (1 hard of 2), Underground pipeline systems (1 hard of 2), Water measurement: weirs, Parshall flume and orifices (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Soil-water-plant relations: field capacity, wilting point and MAD (1 easy of 2); Furrow irrigation (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Irrigation Association Certified Irrigation Designer Irrigation Engineering (Soil-Water-Pl

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.