LAISHA
Open Laisha

Irrigation Association Certified Agricultural Irrigation Specialist Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods): practice questions

Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) · USA · Irrigation Association

Original practice questions written to the published syllabus · not past papers
10worked here, free
21written to this exam in this subject
9syllabus units

About Irrigation Association Certified Agricultural Irrigation Specialist

Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) is a professional certification run by Irrigation Association, for candidates in USA. 100 MCQs, 3 hours.

Source: irrigation.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Irrigation Association Certified Agricultural Irrigation Specialist

How much water a crop needs, when to give it, how to measure and convey it, and how to design surface irrigation.

Our 21 Irrigation Association Certified Agricultural Irrigation Specialist questions in this subject: 3 easy, 13 medium, 5 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Irrigation Association Certified Agricultural Irrigation Specialist and are not shown on any other exam's page.

Question 1 · medium

A clay loam has volumetric field capacity 0.32 and wilting point 0.14. With a 1.2 m root zone and a management allowed depletion of 50 %, what is the readily available water?

  1. 192 mm
  2. 84 mm
  3. 216 mm
  4. 108 mm
Answer and working

D. 108 mm

TAW = 1000 × (0.32 − 0.14) × 1.2 = 216 mm. RAW = 0.5 × 216 = 108 mm. 216 mm is TAW, not RAW; 192 mm applies MAD to field capacity alone; 84 mm applies it to the wilting point water, which is unavailable.

Question 2 · medium

When sizing the pump and main pipeline for a new irrigation system, which crop water figure should normally govern capacity?

  1. Peak-period ETc (net of dependable rain) for the design year, divided by efficiency and adjusted for operating hours
  2. The average July rainfall deficit over 30 years
  3. Mean annual reference ET
  4. Seasonal total ETc divided by the season length (the seasonal mean), since averaging over the season gives the safest and most economical design figure
Answer and working

A. Peak-period ETc (net of dependable rain) for the design year, divided by efficiency and adjusted for operating hours

Capacity must meet the highest sustained demand; averaging over the season or year undersizes the system and causes stress in the peak period. Operating hours per day and efficiency then convert the net peak rate to a flow.

Question 3 · easy

Total available water in the root zone is 150 mm, MAD is 40 % and peak ETc is 6 mm/day. What is the irrigation interval at peak?

  1. 25 days
  2. 6 days
  3. 15 days
  4. 10 days
Answer and working

D. 10 days

Allowable depletion = 0.40 × 150 = 60 mm; interval = 60/6 = 10 days. 25 days uses the full TAW; 15 days uses MAD = 0.6; 6 days confuses ETc with the interval.

Question 4 · medium

A 3 ft³/s stream is applied to a 12-acre field for 10 hours. Roughly what average depth is applied?

  1. 2.5 in
  2. 30 in
  3. 0.25 in
  4. 4 in
Answer and working

A. 2.5 in

1 ft³/s for 1 hour ≈ 1 acre-inch (1.008). Q t = A d gives d = 3 × 10 / 12 = 2.5 in (more exactly 2.52 in). 0.25 in is a decimal slip; 30 in forgets to divide by area; 4 in divides area by flow.

Question 5 · medium

Where should tensiometers be installed to schedule a deep-rooted row crop?

  1. In the furrow bottom, where water stands longest, with both instruments at the same shallow depth so that their readings can be averaged
  2. One in the upper root zone to trigger irrigation and one near its bottom to check that water reached it without excess drainage
  3. Only just below the soil surface, at 2–3 cm
  4. Only below the root zone
Answer and working

B. One in the upper root zone to trigger irrigation and one near its bottom to check that water reached it without excess drainage

Most extraction is in the upper root zone, so the trigger sensor goes there; a deeper sensor shows whether the irrigation refilled the lower zone or drained past it. Surface readings fluctuate with evaporation, and sensors below the roots do not see crop use.

Question 6 · medium

A 3-ft Parshall flume reads Ha = 0.50 ft and Hb = 0.40 ft. Which is correct?

  1. Submergence is 80 %, below the 90 % limit for flumes of this size, so the free-flow equation can be applied unchanged
  2. Submergence is 125 %, so the flume is flowing backward
  3. Submergence is 80 %, above the 70 % free-flow limit for this size, so a submergence correction must be applied
  4. Submergence is 20 %, so flow is free
Answer and working

C. Submergence is 80 %, above the 70 % free-flow limit for this size, so a submergence correction must be applied

Submergence = Hb/Ha = 0.40/0.50 = 80 %. For 1–8 ft flumes free flow holds up to 70 %, so the flow is submerged and the free-flow rating overstates discharge unless corrected. 125 % inverts the ratio; 20 % is 1 − Hb/Ha.

Question 7 · hard

A buried plastic pipeline 300 m long, 200 mm internal diameter, carries 30 L/s. Using Hazen-Williams with C = 150 (SI: hf = 10.67 L Q^1.852 / (C^1.852 D^4.87)), what is the friction loss?

  1. 11.4 m
  2. 2.43 m
  3. 1.14 m
  4. 0.039 m
Answer and working

C. 1.14 m

hf = 10.67 × 300 × 0.03^1.852 / (150^1.852 × 0.2^4.87) = 1.14 m. 10× results from taking L as 3,000 m; 0.039 m uses a 400 mm pipe (diameter doubled); 2.43 m uses C = 100, a value for old rough pipe, not plastic.

Question 8 · hard

Which pair of factors most determines the uniformity achieved in a level basin?

  1. Precision of land levelling and inflow rate relative to the soil intake rate
  2. Dike height and bund width
  3. Distance from the weather station and field shape
  4. Crop coefficient and pan coefficient
Answer and working

A. Precision of land levelling and inflow rate relative to the soil intake rate

Level basins depend on fast, even coverage: a precisely levelled surface and a large stream relative to intake make opportunity time nearly uniform. Dike size matters only for containing the depth.

Question 9 · hard

Compared with a sandy soil, how should furrow spacing typically be set on a clay soil?

  1. Wider, because clay has higher infiltration rate
  2. Narrower, because clay has lower lateral movement of water between neighbouring furrows
  3. Wider, as clay spreads water sideways more
  4. The same, because spacing depends only on the crop
Answer and working

C. Wider, as clay spreads water sideways more

In clays, capillary forces spread water sideways well relative to downward movement, so the wetted bulb is wide and furrows can be farther apart. In sands, water moves mostly downward, so furrows must be closer. Clay usually has a lower, not higher, intake rate.

Question 10 · medium

Catch-can depths along a field (mm) are 10, 12, 8, 14, 6 and 10. What is Christiansen's coefficient of uniformity?

  1. 86.7 %
  2. 80.0 %
  3. -20.0 %
  4. 60.0 %
Answer and working

B. 80.0 %

Mean = 10 mm; absolute deviations 0, 2, 2, 4, 4, 0 sum to 12. CU = 100 (1 − 12 / (6 × 10)) = 80.0 %. 60 % is the minimum divided by the mean; −20 % forgets to divide by n; 86.7 % uses the range instead of summed deviations.

A study plan for Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Irrigation Association Certified Agricultural Irrigation Specialist

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 21 questions): Irrigation efficiencies and distribution uniformity (4, 19%); Furrow irrigation (3, 14%); Irrigation scheduling (3, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Basin irrigation (2, 10%); Crop coefficients and crop water requirement (2, 10%); Soil-water-plant relations: field capacity, wilting point and MAD (2, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Underground pipeline systems (2, 10%); Water measurement: weirs, Parshall flume and orifices (2, 10%); Effective rainfall (1, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Basin irrigation (1 hard of 2), Underground pipeline systems (1 hard of 2), Water measurement: weirs, Parshall flume and orifices (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Soil-water-plant relations: field capacity, wilting point and MAD (1 easy of 2); Furrow irrigation (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Irrigation Association Certified Agricultural Irrigation Specialist Irrigation Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.