LAISHA
Open Laisha

Irrigation Association Certified Agricultural Irrigation Specialist Sprinkler & Micro-Irrigation Systems: practice questions

Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) · USA · Irrigation Association

Original practice questions written to the published syllabus · not past papers
10worked here, free
37written to this exam in this subject
14syllabus units

About Irrigation Association Certified Agricultural Irrigation Specialist

Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) is a professional certification run by Irrigation Association, for candidates in USA. 100 MCQs, 3 hours.

Source: irrigation.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Sprinkler & Micro-Irrigation Systems in Irrigation Association Certified Agricultural Irrigation Specialist

Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.

Our 37 Irrigation Association Certified Agricultural Irrigation Specialist questions in this subject: 3 easy, 24 medium, 10 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Irrigation Association Certified Agricultural Irrigation Specialist and are not shown on any other exam's page.

Question 1 · medium

A sprinkler lateral is laid down a uniform gentle slope from its inlet. Compared with the same lateral on level ground, what does the slope do?

  1. It always increases the pressure variation
  2. It has no effect, because the sprinkler operating pressure is set once at the pump and does not change along the lateral
  3. Elevation gain offsets friction, so a longer lateral or smaller pipe can meet the same pressure limit
  4. It usually reverses the sign of the friction loss
Answer and working

C. Elevation gain offsets friction, so a longer lateral or smaller pipe can meet the same pressure limit

Going downhill, each metre of fall adds pressure that offsets friction loss; on gentle slopes the profile flattens and the allowable length grows. On steep slopes the gain can exceed friction and the end pressure rises, which again needs checking.

Question 2 · medium

What distinguishes an in-line emitter from an on-line emitter?

  1. In-line emitters are built into the tubing during manufacture; on-line emitters are punched into it later
  2. In-line emitters are always pressure-compensating, whereas on-line emitters never are, whatever the model or maker
  3. On-line emitters are used only below ground
  4. In-line emitters discharge more than 20 L/h
Answer and working

A. In-line emitters are built into the tubing during manufacture; on-line emitters are punched into it later

The distinction is physical: in-line emitters are inserted or formed inside the tube at the factory at fixed spacing (as in dripline and tape); on-line emitters are inserted into punched holes in the field at chosen spacings. Either type can be pressure-compensating.

Question 3 · hard

Ten new emitters tested at the same pressure give (L/h): 3.9, 4.1, 4.0, 3.8, 4.2, 4.0, 4.1, 3.9, 4.3, 3.7. What is the manufacturing coefficient of variation (sample standard deviation), and how does ASABE EP405 class it for point-source emitters?

  1. 0.046; average
  2. 0.046; good
  3. 0.183; marginal
  4. 0.150; unacceptable
Answer and working

B. 0.046; good

Mean = 4.00 L/h; sample s = 0.1826 L/h; Cv = s/mean = 0.046. Below 0.05 is 'good' in EP405. 0.183 is the standard deviation without dividing by the mean; 0.15 is the range over the mean.

Question 4 · easy

Under ASABE EP405, a point-source emitter with a manufacturing coefficient of variation of 0.06 is classed as:

  1. Average
  2. Good
  3. Marginal
  4. Unacceptable
Answer and working

A. Average

EP405 classes for point-source emitters: below 0.05 good, 0.05–0.07 average, 0.07–0.11 marginal, 0.11–0.15 poor, above 0.15 unacceptable.

Question 5 · medium

Which emitter type is most sensitive to water temperature, and why?

  1. Turbulent orifice emitters, because water density changes strongly with temperature and alters discharge
  2. Long-path laminar emitters, because discharge depends on viscosity, which falls as temperature rises
  3. Pressure-compensating emitters, because the diaphragm melts
  4. Vortex emitters, because vortex strength depends on temperature
Answer and working

B. Long-path laminar emitters, because discharge depends on viscosity, which falls as temperature rises

In laminar flow, head loss depends directly on viscosity; water viscosity falls markedly as it warms, so discharge rises. Turbulent flow is nearly independent of viscosity, and water density changes very little over field temperatures.

Question 6 · easy

Bralts' statistical uniformity is Us = 100 (1 − Vq). If the measured emitter flows have a coefficient of variation of 0.12, Us equals:

  1. 12 %
  2. 85 %
  3. 88 %
  4. 94 %
Answer and working

C. 88 %

Us = 100 × (1 − 0.12) = 88 %. 12 % confuses the variation with the uniformity; 85 % applies a 1.27 multiplier that belongs to the Keller–Karmeli formula, not Bralts'. 94 % halves the coefficient of variation.

Question 7 · medium

What is the main purpose of fitting a pressure regulator at the inlet of each drip sub-main on hilly land?

  1. To raise pressure above the pump's delivery head, so that blocks higher up the hill still receive their full design pressure
  2. To act as a filter
  3. To isolate each block from mainline pressure variation, so the block's allowable variation is used only within it
  4. To measure flow into the block
Answer and working

C. To isolate each block from mainline pressure variation, so the block's allowable variation is used only within it

On undulating land, mainline pressure differs widely between blocks. A regulator at each sub-main inlet delivers a set pressure, so the lateral and sub-main allowance is not consumed by mainline variation. It cannot raise pressure above the supply.

Question 8 · medium

A drip system draws from an open farm pond with heavy algae growth in summer. Which primary filter is most appropriate?

  1. Media (sand/gravel) filter, backflushable
  2. Hydrocyclone (centrifugal separator) alone
  3. Single screen filter
  4. No filter; chlorinate only
Answer and working

A. Media (sand/gravel) filter, backflushable

Media filters trap organic material in the depth of the bed and are backflushed; they are the standard primary filter for surface water with algae. A screen alone clogs quickly with algae; a hydrocyclone does not remove organic matter; chlorination complements, but does not replace, filtration.

Question 9 · medium

In chemigation safety equipment, where is the main check valve placed?

  1. In the injection line only
  2. In the irrigation line between the water source/pump and the injection point
  3. At the end of each lateral
  4. Downstream of the last filter at the block valve, just before the laterals begin
Answer and working

B. In the irrigation line between the water source/pump and the injection point

The irrigation-line check valve prevents water containing chemicals from flowing back to the well or source; it sits between the pump and the injection point, with a vacuum-relief valve and low-pressure drain upstream of it. The injection line has its own check valve as well.

Question 10 · medium

Why is clean water run through a drip system for a period after fertiliser injection stops?

  1. To dilute the soil solution around the emitters to zero salinity before the next fertiliser application
  2. To cool the pump
  3. To flush fertiliser out of laterals and emitters, preventing precipitation, clogging and uneven doses
  4. To backflush the media filter
Answer and working

C. To flush fertiliser out of laterals and emitters, preventing precipitation, clogging and uneven doses

Fertiliser left in the laterals can precipitate or support microbial growth as it dries, and emitters near the head would otherwise receive a different total than distant ones. The flush time must be at least the travel time from injector to the farthest emitter.

A study plan for Sprinkler & Micro-Irrigation Systems in Irrigation Association Certified Agricultural Irrigation Specialist

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 37 questions): Fertigation (5, 14%); Filtration (5, 14%); System layout and pump selection (4, 11%); Automation (3, 8%); Emission uniformity (3, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Emitter hydraulics: exponent and coefficient of variation (3, 8%); Christiansen's uniformity coefficient (2, 5%); Drip lateral and sub-main design (2, 5%); Drip system components (2, 5%); Economics of pressurised irrigation (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Sprinkler lateral and main design (2, 5%); Sprinkler spacing and application rate (2, 5%); Allowable pressure variation and the friction factor F (1, 3%); Sprinkler types and components (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Christiansen's uniformity coefficient (1 hard of 2), Drip system components (1 hard of 2), Economics of pressurised irrigation (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Emission uniformity (1 easy of 3); Emitter hydraulics: exponent and coefficient of variation (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Irrigation Association Certified Agricultural Irrigation Specialist Sprinkler & Micro-Irri

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.