LAISHA
Open Laisha

Nepal Engineering Council Registration Exam Sprinkler & Micro-Irrigation Systems: practice questions

Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council

Original practice questions written to the published syllabus · not past papers
10worked here, free
55written to this exam in this subject
14syllabus units

About Nepal Engineering Council Registration Exam

Nepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.

Official site: nec.gov.np.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Sprinkler & Micro-Irrigation Systems in Nepal Engineering Council Registration Exam

Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.

Our 55 Nepal Engineering Council Registration Exam questions in this subject: 33 easy, 20 medium, 2 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.

Question 1 · easy

A low-cost drip kit for a vegetable plot in the Nepal mid-hills is fed by gravity from a drum whose water surface is 2 m above the laterals. Neglecting losses, the pressure at the lateral inlet is closest to:

  1. 2 kPa
  2. 20 kPa
  3. 200 kPa
  4. 0.2 kPa
Answer and working

B. 20 kPa

Pressure = ρgh = 1000 × 9.81 × 2 ≈ 19.6 kPa, so about 20 kPa (2 m of head). 2 kPa and 0.2 kPa slip one or two powers of ten in the conversion. 200 kPa is 20 m of head, the range of a pumped sprinkler system, not a 2 m drum. Gravity kits work because their emitters or micro-tubes are made for such low heads.

Question 2 · easy

Sprinklers discharging 0.45 L/s each are set 12 m apart along the lateral, with laterals 15 m apart, on a Terai wheat field. The average application rate is:

  1. 0.9 mm/h
  2. 13.5 mm/h
  3. 7.2 mm/h
  4. 9.0 mm/h
Answer and working

D. 9.0 mm/h

Application rate = q / (Sl × Sm) = (0.45 × 3600 L/h) / (12 × 15 m²) = 1620 / 180 = 9.0 mm/h (1 L/m² = 1 mm). 0.9 mm/h is a factor-of-ten slip. 13.5 mm/h divides by 12 × 10 m, a closer spacing than given. 7.2 mm/h divides by 15 × 15 m.

Question 3 · medium

Five catch cans in a sprinkler test collect 14, 16, 15, 12 and 18 mm. Christiansen's uniformity coefficient is:

  1. 89.3%
  2. 80.0%
  3. 94.7%
  4. 66.7%
Answer and working

A. 89.3%

Mean = 75 / 5 = 15 mm; absolute deviations are 1, 1, 0, 3 and 3, total 8 mm. CU = 100 (1 − 8 / 75) = 89.3%. 80.0% is the minimum catch divided by the mean (12/15), not Christiansen's formula. 94.7% halves the deviation sum. 66.7% is the minimum divided by the maximum (12/18).

Question 4 · medium

Drip laterals on steep hill terraces run down the slope, so emitter pressures vary widely along each line. Which emitter type best keeps discharges uniform?

  1. Long-path laminar emitters, discharge exponent near 1.0
  2. Pressure-compensating emitters, exponent near 0
  3. Orifice-type turbulent emitters, exponent near 0.5
  4. Vortex emitters, discharge exponent near 0.4
Answer and working

B. Pressure-compensating emitters, exponent near 0

In q = kHˣ, the smaller the exponent x, the less discharge changes with pressure; pressure-compensating emitters, with a flexible diaphragm, have x close to 0 over their working range, which suits steep slopes. Laminar long-path emitters (x ≈ 1) change flow almost in proportion to pressure, the worst case. Orifice (x ≈ 0.5) and vortex (x ≈ 0.4) emitters are better than laminar ones but still change flow noticeably with the large head differences on hills.

Question 5 · medium

A level sprinkler lateral is to run at an average pressure head of 28 m. Its friction loss is 4.8 m and the risers are 1.2 m high. The pressure head needed at the lateral inlet is:

  1. 34.0 m
  2. 30.4 m
  3. 32.8 m
  4. 31.6 m
Answer and working

C. 32.8 m

For a level lateral, Hi = Ha + ¾hf + Hr = 28 + 3.6 + 1.2 = 32.8 m; about three-quarters of the friction loss occurs upstream of the point of average pressure. 34.0 m adds the whole friction loss. 30.4 m adds only half of it. 31.6 m leaves out the riser height.

Question 6 · hard

A sprinkler lateral has 15 equally spaced outlets, the first one full spacing from the inlet. If the same pipe carrying the full flow to its end would lose 8.0 m by Hazen-Williams (m = 1.852), the friction loss in the lateral is closest to:

  1. 3.1 m
  2. 2.8 m
  3. 4.0 m
  4. 8.0 m
Answer and working

A. 3.1 m

Christiansen's F = 1/(m+1) + 1/(2N) + √(m−1)/(6N²) = 0.351 + 0.033 + 0.001 ≈ 0.385, so hf = 0.385 × 8.0 ≈ 3.1 m. 2.8 m uses the limiting value 1/(m+1) = 0.35, which applies only for a very large number of outlets. 4.0 m simply halves the loss. 8.0 m ignores the fact that flow falls at every outlet.

Question 7 · medium

A farmer wants to apply 30 kg N/ha through drip to a 0.5 ha tomato field using urea (46% N). The amount of urea needed for this dose is:

  1. 15.0 kg
  2. 65.2 kg
  3. 32.6 kg
  4. 6.9 kg
Answer and working

C. 32.6 kg

N needed = 30 × 0.5 = 15 kg; urea = 15 / 0.46 = 32.6 kg. 15.0 kg is the nitrogen, not the fertiliser. 65.2 kg is the urea for a full hectare. 6.9 kg multiplies by 0.46 instead of dividing.

Question 8 · medium

A pump lifts 5 L/s from a river intake against a total dynamic head of 30 m to supply a sprinkler system. If pump efficiency is 60%, the shaft power needed is:

  1. 1.47 kW
  2. 2.45 kW
  3. 4.09 kW
  4. 0.88 kW
Answer and working

B. 2.45 kW

P = ρgQH / η = 1000 × 9.81 × 0.005 × 30 / 0.6 ≈ 2452 W = 2.45 kW. 1.47 kW is the water power, before allowing for efficiency. 4.09 kW divides by the efficiency twice. 0.88 kW multiplies by the efficiency instead of dividing.

Question 9 · easy

Drip laterals in a field fed by silty stream water are fitted with removable end caps or flush valves at their tail ends. Their purpose is to:

  1. let sediment that settles in the laterals be flushed out
  2. raise the operating pressure at the last emitters
  3. allow fertiliser to be injected at the far end
  4. release air when the system is first filled
Answer and working

A. let sediment that settles in the laterals be flushed out

Fine silt that passes the filter settles where velocity is lowest, at the end of each lateral; opening the end lets it be flushed out before it blocks emitters. A closed end does not raise pressure in a useful way, and an open one lowers it. Fertiliser is injected at the head unit, not at lateral ends. Air release is the job of air-release and vacuum valves at high points of mains and sub-mains.

Question 10 · hard

A sprinkler set costs NPR 200,000 and lasts 8 years with no salvage value. At 10% interest, its equivalent annual cost is closest to:

  1. NPR 25,000
  2. NPR 45,000
  3. NPR 20,000
  4. NPR 37,488
Answer and working

D. NPR 37,488

Annual cost = P × CRF, where CRF = i(1+i)ⁿ / ((1+i)ⁿ − 1) = 0.1 × 2.1436 / 1.1436 = 0.18744, so 200,000 × 0.18744 = NPR 37,488. NPR 25,000 is straight-line depreciation with no interest. NPR 45,000 adds interest on the whole first cost every year, which overstates the cost. NPR 20,000 is the interest alone.

A study plan for Sprinkler & Micro-Irrigation Systems in Nepal Engineering Council Registration Exam

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 55 questions): Drip system components (8, 15%); Economics of pressurised irrigation (5, 9%); Sprinkler spacing and application rate (5, 9%); Sprinkler types and components (5, 9%); Allowable pressure variation and the friction factor F (4, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Christiansen's uniformity coefficient (4, 7%); Fertigation (4, 7%); Filtration (4, 7%); Sprinkler lateral and main design (4, 7%); Automation (3, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Emitter hydraulics: exponent and coefficient of variation (3, 5%); System layout and pump selection (3, 5%); Drip lateral and sub-main design (2, 4%); Emission uniformity (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Allowable pressure variation and the friction factor F (1 hard of 4), Economics of pressurised irrigation (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Drip lateral and sub-main design (2 easy of 2); Emission uniformity (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Nepal Engineering Council Registration Exam Sprinkler & Micro-Irrigation Systems

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.