LAISHA
Open Laisha

Nepal Engineering Council Registration Exam Engineering Mechanics (Statics & Dynamics): practice questions

Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council

Original practice questions written to the published syllabus · not past papers
10worked here, free
25written to this exam in this subject
9syllabus units

About Nepal Engineering Council Registration Exam

Nepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.

Official site: nec.gov.np.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Engineering Mechanics (Statics & Dynamics) in Nepal Engineering Council Registration Exam

Forces, equilibrium and motion of particles and rigid bodies: the starting point for structures, machines and tractor mechanics.

Our 25 Nepal Engineering Council Registration Exam questions in this subject: 10 easy, 14 medium, 1 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.

Question 1 · medium

Two chains pull on a tree stump from one ring with forces of 6 kN and 4 kN; the angle between the chains is 120 degrees. What is the magnitude of the resultant pull on the stump?

  1. 8.72 kN
  2. 7.21 kN
  3. 10.00 kN
  4. 5.29 kN
Answer and working

D. 5.29 kN

R = sqrt(P^2 + Q^2 + 2PQ cos theta) = sqrt(36 + 16 + 2 x 6 x 4 x cos 120) = sqrt(28) = 5.29 kN. Using +cos 60 instead of cos 120 gives 8.72 kN; treating the chains as perpendicular gives 7.21 kN; adding arithmetically gives 10 kN, which is only right for chains pulling in the same direction.

Question 2 · easy

The top link of a tractor's three-point hitch is pinned at both ends and carries no load between them. Ignoring its own weight, its force must act:

  1. Perpendicular to the line joining its two pin centres
  2. Vertically downward through its own midpoint
  3. In whatever direction the implement load acts
  4. Along the straight line joining its two pin centres
Answer and working

D. Along the straight line joining its two pin centres

A member loaded only at two pins is a two-force member; equilibrium requires the two end forces to be equal, opposite and collinear, so the force lies along the line joining the pins. That is why the top link is either in tension or in compression.

Question 3 · easy

A 4 m simply supported beam in a feed store carries a 6 kN point load 1 m from the left support. What is the left support reaction?

  1. 1.5 kN
  2. 3.0 kN
  3. 4.5 kN
  4. 6.0 kN
Answer and working

C. 4.5 kN

Moments about the right support: RA x 4 = 6 x 3, RA = 4.5 kN, and RB = 6 - 4.5 = 1.5 kN. The nearer support carries more; 1.5 kN reverses the arms and 3 kN assumes a central load.

Question 4 · easy

A plane pin-jointed roof truss has 7 joints and is supported by one pin and one roller. How many members does it need to be simple and statically determinate?

  1. 14
  2. 10
  3. 12
  4. 11
Answer and working

D. 11

For a plane truss, m = 2j - 3 = 2 x 7 - 3 = 11. Using 2j gives 14; forgetting the 3 rigid-body equations is the common slip. More than 11 members makes it indeterminate; fewer makes it a mechanism. 10 uses j + 3; 12 subtracts only the two pin reactions (2j − 2).

Question 5 · medium

A symmetric triangular truss with a 6 m span and 1.5 m rise carries 8 kN at its apex on a pin and a roller. What is the force in each rafter?

  1. 8.94 kN tension
  2. 8.94 kN compression
  3. 8.00 kN compression
  4. 3.58 kN compression
Answer and working

B. 8.94 kN compression

Reactions 4 kN each. theta = arctan(1.5/3) = 26.57 degrees. Vertical equilibrium at the support: F_rafter = 4 / sin theta = 8.94 kN, pushing into the joint, so compression. 8.00 kN is the tie force; rafters of a gable truss under gravity load are always in compression.

Question 6 · medium

A plane truss on a pin and a roller has 6 joints and 10 members. It is:

  1. Statically determinate and just rigid
  2. A mechanism, one member short of stable
  3. Internally indeterminate with one redundant member
  4. Internally indeterminate with two redundant members
Answer and working

C. Internally indeterminate with one redundant member

2j - 3 = 9. With m = 10 there is one member more than needed, so member forces cannot be found by statics alone; the truss is indeterminate to the first degree.

Question 7 · medium

For the same cross-sectional area of steel, why does an I-section or box-section chassis rail resist bending far better than a solid square bar?

  1. It places more of its area close to the neutral axis, which lowers the bending stress there
  2. It places more of its area far from the neutral axis, greatly raising the second moment of area
  3. It raises the polar moment of inertia, and bending strength depends on polar inertia alone
  4. It raises the mass moment of inertia, which damps the bending loads from rough ground
Answer and working

B. It places more of its area far from the neutral axis, greatly raising the second moment of area

Second moment of area weights each element by the square of its distance from the axis (the A d^2 terms). Moving material into flanges far from the neutral axis raises I, and so bending stiffness and strength, without adding steel.

Question 8 · medium

A 3000 kg tractor takes a level curve of 15 m radius at 5 m/s. What total sideways friction force must the tyres supply?

  1. 1.0 kN
  2. 5.0 kN
  3. 49.0 kN
  4. 0.39 kN
Answer and working

B. 5.0 kN

Centripetal force = m v^2 / r = 3000 x 25 / 15 = 5000 N = 5.0 kN, supplied by tyre side friction. Using v instead of v^2 gives 1.0 kN; multiplying by g treats the mass as a weight. 0.39 kN reads 5 m/s as 5 km/h (1.389 m/s).

Question 9 · easy

A worker drags a sledge of seed 50 m along level ground with a rope tension of 300 N inclined 30 degrees above the horizontal. How much work does the rope do?

  1. 15.00 kJ
  2. 7.50 kJ
  3. 12.99 kJ
  4. 8.66 kJ
Answer and working

C. 12.99 kJ

W = F s cos theta = 300 x 50 x cos 30 = 12990 J = 12.99 kJ. The vertical component does no work because the sledge does not move vertically; using sin 30 takes the wrong component. 15.00 kJ uses the full tension; 7.50 kJ uses sin 30; 8.66 kJ uses tan 30.

Question 10 · medium

An ideal hydraulic jack has a pump piston of 20 mm diameter and a lifting ram of 80 mm diameter. What force on the pump piston supports 16 kN on the ram?

  1. 1.0 kN
  2. 4.0 kN
  3. 0.25 kN
  4. 256 kN
Answer and working

A. 1.0 kN

Equal pressure (or virtual work with equal displaced volume): F1 / A1 = F2 / A2, so F1 = 16 x (20/80)^2 = 16 / 16 = 1.0 kN. Using the diameter ratio instead of the area ratio gives 4 kN. 0.25 kN cubes the diameter ratio; 256 kN multiplies by the area ratio instead of dividing.

A study plan for Engineering Mechanics (Statics & Dynamics) in Nepal Engineering Council Registration Exam

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (60% of the 25 questions): Analysis of trusses and frames (6, 24%); Free-body diagrams and equilibrium (5, 20%); Force systems and resultants (4, 16%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Area and mass moment of inertia (3, 12%); Centroid and centre of gravity (2, 8%); Virtual work (2, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Impulse and momentum (1, 4%); Kinetics: Newton's laws and D'Alembert's principle (1, 4%); Work-energy principle (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Free-body diagrams and equilibrium (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Work-energy principle (1 easy of 1); Free-body diagrams and equilibrium (4 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Nepal Engineering Council Registration Exam Engineering Mechanics (Statics & Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.