Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council
Original practice questions written to the published syllabus · not past papersNepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.
Official site: nec.gov.np.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Turning crop residues, dung and oils into fuel: briquettes, gasifiers, biogas plants and liquid biofuels, and auditing farm energy.
Our 32 Nepal Engineering Council Registration Exam questions in this subject: 8 easy, 19 medium, 5 hard, across 13 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.
A tumbling-box (or rotating drum) test on pellets or briquettes is used to measure:
D. Mechanical durability: the share surviving handling without breaking into fines
Durability testing tumbles a known mass for a set number of revolutions, sieves out fines, and reports the mass retained as a percentage. Low durability means dust, losses and feeding problems in stoves and boilers. Calorific value needs a bomb calorimeter and ash fusion needs a heated microscope or furnace test.
A gasifier–engine–generator set delivers 20 kW of electricity with an overall biomass-to-electricity efficiency of 20% (LHV basis). Biomass LHV is 15 MJ/kg. The biomass consumption and specific fuel consumption are:
B. 24 kg/h and 1.2 kg/kWh
Fuel power = 20 ÷ 0.2 = 100 kW = 360 MJ/h. Biomass = 360 ÷ 15 = 24 kg/h. Specific consumption = 24 ÷ 20 = 1.2 kg/kWh, within the 1–1.5 kg/kWh range commonly reported for small woody-biomass systems. Ignoring the efficiency gives the fuel for a perfect converter.
The most serious safety hazard specific to operating a producer-gas plant in an enclosed shed is:
B. Carbon monoxide poisoning from gas leaks at start-up, shut-down or filter servicing
Producer gas typically contains about 15–25% CO, a colourless, odourless and highly toxic gas. Plants need good ventilation, flares for start-up gas, CO detectors and procedures that never let operators work on open gas lines alone. Explosion risk also exists when air leaks into gas spaces, but CO exposure is the chronic, specific danger.
The mesophilic temperature range, within which most farm biogas plants operate, is about:
B. 30–40 °C (optimum near 35–37 °C)
Mesophilic digestion runs at about 30–40 °C. Thermophilic digestion (about 50–60 °C, often 55 °C) is faster and destroys more pathogens but is less stable and needs heating. Below about 20 °C (psychrophilic) gas production is slow, which is why unheated plants in cold regions or winters need longer retention times.
In a floating-drum biogas plant, the gas is delivered at:
B. A nearly constant pressure
The gas holder floats on the slurry (or in a water jacket) and rises as gas collects; the pressure equals the drum's weight divided by its area and stays nearly constant. In a fixed-dome plant, pressure rises as gas displaces slurry into the outlet chamber, so pressure varies with the amount of stored gas.
Compared with a floating-drum (KVIC-type) plant of the same capacity, a fixed-dome plant (Janata or Deenbandhu type) generally has:
C. Lower cost and no moving steel parts, but variable gas pressure and a need for skilled masonry
Fixed-dome plants are built of brick or concrete, usually underground; the dome stores gas by pushing slurry into a displacement (outlet) chamber, so pressure varies. With no steel drum they are cheaper and long-lived, but cracks in the dome leak gas and are hard to repair. Floating-drum plants give constant pressure and a visible gas store but the steel drum corrodes and needs maintenance.
The Deenbandhu biogas plant, developed in India in the 1980s, reduced cost compared with the earlier Janata fixed-dome design mainly by:
B. Using a geometry made of spherical segments that reduces the masonry surface area for a given volume
Spherical shapes enclose the most volume for the least surface, so less brick and cement are needed. The Deenbandhu design (developed by a voluntary agency, AFPRO) was cheaper than the Janata design and was widely adopted in India's national biogas programme. It is still a fixed-dome, unheated, mesophilic plant.
A digester of 8 m³ active volume receives 0.2 m³ of slurry per day. Its hydraulic retention time is:
B. 40 days
HRT = volume ÷ daily flow = 8 ÷ 0.2 = 40 days. It is the average time a parcel of slurry spends in the digester. 1.6 days multiplies instead of dividing; 0.025 days inverts the ratio; 20 days takes the daily flow as 0.4 m³ by adding the 1:1 dilution water again.
A village cooperative plans to make biodiesel from used frying oil with a high free fatty acid content. The most suitable process choice is:
C. Acid-catalysed esterification of the FFA, then alkali transesterification, using dried oil
Adding extra alkali turns FFA into soap, which emulsifies the product and cuts yield, and water in the oil hydrolyses esters to more FFA. The two-step route converts FFA to esters with an acid catalyst (for example sulphuric acid with methanol), then completes transesterification with a base. Methanol is toxic and flammable, so safe storage and ventilation are part of the design.
The first step in a walk-through energy audit of a rice mill is to:
A. Gather energy and production records (bills, husk use) and map the main energy-using equipment
An audit starts by establishing a baseline: how much energy of each kind is used, where, and per tonne of output (specific energy consumption). That shows where the large losses are, such as boiler and parboiling steam, dryer furnaces or oversized motors, before any investment is chosen. Replacement decisions come after measurement and economic analysis.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.