ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Unit V renewable energy: definitions and principles of proximate and ultimate analysis, calorific value, briquetting, updraft vs downdraft gasifiers, producer gas composition, dual-fuel engines, anaerobic digestion stages and conditions, KVIC vs fixed-dome plants, ethanol and biodiesel basics, with short calculations.
Turning crop residues, dung and oils into fuel: briquettes, gasifiers, biogas plants and liquid biofuels, and auditing farm energy.
Our 79 ICAR AIEEA-PG questions in this subject: 32 easy, 44 medium, 3 hard, across 13 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
Freshly cut wood contains 40% moisture on a wet basis. Its moisture content on a dry basis is:
C. 66.7%
Take 100 kg of wet wood: 40 kg water and 60 kg dry matter. Dry basis = water ÷ dry matter = 40 ÷ 60 × 100 = 66.7%. The dry-basis figure is always larger than the wet-basis figure for the same wood. 28.6% divides the water by wet mass plus water, 40 ÷ 140.
In binderless high-pressure briquetting of woody residues, the main natural binding agent is:
D. Lignin, which softens under heat and pressure and bonds particles on cooling
At the temperatures reached in a heated die or by friction, lignin softens and flows between particles, then sets on cooling. That is why screw and piston presses can work without binders on lignin-rich residues. Starch or molasses binders are used in low-pressure briquetting. Silica melts at well over 1000 °C, far above die temperatures.
For most binderless briquetting and pelleting, the feed moisture content is usually kept at roughly:
A. About 8–12% (wet basis)
Some water helps: it lubricates particles and lowers the softening temperature of lignin. Too much water turns to steam in the die and cracks or bursts the briquette; too little leaves poor bonding. Operating windows around 8–12% are widely recommended, with the exact optimum depending on feedstock and machine.
The optimum pH range for methanogenic digestion is about:
D. 6.8–7.2
Methanogens are the most pH-sensitive group; methane production is best near neutral pH, roughly 6.8–7.2, and falls sharply below about 6.5. A falling pH signals accumulating volatile fatty acids (souring), usually from overloading. pH 4–5 suits yeast fermentation to ethanol, not methanogenesis. pH 8.5–9.5 raises free-ammonia toxicity, and pH 2–3 stops methanogens entirely.
The chamber of a fixed-dome biogas plant into which slurry is pushed as gas accumulates, and from which digested slurry overflows, is called the:
D. Outlet (displacement) chamber
As gas collects under the dome it pushes slurry down in the digester and up into the outlet chamber; the level difference between the two is the gas pressure. When gas is used, slurry flows back. The mixing tank is at the inlet, the guide frame belongs to floating-drum plants, and the water trap removes condensate from the gas pipe.
A plant is fed 100 kg of fresh cattle dung per day. If the gas yield is 0.036 m³ per kg of fresh dung, the daily biogas production is:
C. 3.6 m³
Gas = feed × yield = 100 × 0.036 = 3.6 m³/day. Yields per kg of fresh dung are small numbers (a few hundredths of a m³) because fresh dung is about 80% water; typical quoted values vary with diet, climate and plant. 36 m³ is a factor-of-ten slip; 2778 m³ divides the feed by the yield (100 ÷ 0.036); 1.8 m³ halves the answer.
The theoretical maximum ethanol from 100 kg of glucose (ethanol density 0.789 kg/L) is:
B. 51.1 kg (64.8 L)
Mass yield = 2 × 46.07 ÷ 180.16 = 0.511 kg ethanol per kg glucose, so 100 kg gives 51.1 kg. Volume = 51.1 ÷ 0.789 = 64.8 L. Forgetting the 2 in the equation halves the yield; multiplying by density instead of dividing gives too few litres. The remaining 48.9% of the mass leaves as CO2.
Ordinary distillation of a fermented ethanol–water mash cannot yield anhydrous ethanol because:
C. Ethanol and water form an azeotrope at about 95.6% ethanol by mass
At the azeotropic composition the vapour and liquid have the same composition, so further distillation cannot concentrate the ethanol. Fuel ethanol for blending must be nearly water-free, so the rectified spirit is dehydrated, most commonly with molecular sieves (or by azeotropic distillation with an entrainer). Ethanol boils at about 78 °C, below water.
Straight vegetable oil is converted to biodiesel rather than used directly in most modern diesel engines chiefly because the raw oil's:
A. Its viscosity is ten or more times diesel's, causing poor atomisation and injector coking
Transesterification splits the large triglyceride into three smaller ester molecules, lowering viscosity to near that of diesel. Raw oils have heating values only about 10–15% below diesel and negligible sulphur; their viscosity is the problem, together with polymerisation deposits in the combustion chamber.
In agricultural energy analysis, the energy ratio (energy use efficiency) of a crop is defined as:
A. Energy output in the harvested product ÷ energy input to produce it
Energy ratio = output energy ÷ input energy (dimensionless). Input ÷ yield is specific energy (MJ/kg); output − input is net energy. A ratio above 1 means the crop returns more energy than was invested, but the ratio says nothing about food quality or profit.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.