LAISHA
Open Laisha

ICAR AIEEA-PG Soil Science for Engineers: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
92written to this exam in this subject
9syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Soil Science for Engineers in ICAR AIEEA-PG

Single-answer MCQs on soil water constants, infiltration measurement, hydraulic conductivity methods, salinity and sodicity class limits, amendments and short calculations of SAR, ESP, porosity and available water.

The soil an engineer tills, irrigates, drains and builds on: its physical, water and chemical properties.

Our 92 ICAR AIEEA-PG questions in this subject: 36 easy, 46 medium, 10 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

Which master horizon designation is used for hard, consolidated bedrock beneath the soil?

  1. R
  2. O
  3. B
  4. C
Answer and working

A. R

R is hard bedrock. C is unconsolidated, little-altered parent material that can be dug with a spade, O is an organic layer at the surface, and B is the subsoil horizon of illuviation or alteration.

Question 2 · medium

In a constant-head permeameter test, a soil column 15 cm long and 10 cm in diameter under a head difference of 20 cm passes 120 cm³ of water in 30 minutes. What is the saturated hydraulic conductivity?

  1. 0.038 cm/h
  2. 4.07 cm/h
  3. 2.29 cm/h
  4. 0.57 cm/h
Answer and working

C. 2.29 cm/h

A = π × 10²/4 = 78.5 cm²; K = V L/(A h t) = 120 × 15/(78.5 × 20 × 1,800) = 6.37 × 10⁻⁴ cm/s = 2.29 cm/h. Using the diameter as the radius gives 0.57; swapping L and h gives 4.07; converting s to h with 60 instead of 3,600 gives 0.038.

Question 3 · easy

What is the purpose of the outer ring in a double-ring infiltrometer?

  1. It measures evaporation from the soil surface during the test for a correction
  2. It buffers lateral spread so the inner ring measures nearly vertical infiltration
  3. It anchors the inner ring so that it is not pushed out by soil swelling
  4. It holds the reserve water used to keep the inner ring at a constant level
Answer and working

B. It buffers lateral spread so the inner ring measures nearly vertical infiltration

Water from the outer ring wets the soil around the inner ring, so water from the inner ring is not drawn sideways and its fall represents one-dimensional vertical infiltration. Readings are taken from the inner ring only. The outer ring is not an evaporation pan, a reservoir or an anchor.

Question 4 · easy

Which of these will most increase the infiltration rate of a bare, crusting silt loam?

  1. Rolling the surface smooth after sowing to firm the seedbed
  2. Repeated passes with heavy machinery when the soil is wet
  3. Irrigating with low-salinity water that has a high SAR
  4. Keeping crop residue on the surface to absorb raindrop impact
Answer and working

D. Keeping crop residue on the surface to absorb raindrop impact

Residue cover stops raindrop impact from breaking aggregates and forming a seal, so infiltration stays high. Rolling and wet-soil traffic compact the surface, and high-SAR low-salinity water disperses clay and seals the surface, all of which reduce infiltration.

Question 5 · easy

Using the common approximation TDS (mg/L) ≈ 640 × EC (dS/m), what is the total dissolved solids of an irrigation water with EC 2.5 dS/m?

  1. 25 mg/L
  2. 16000 mg/L
  3. 1600 mg/L
  4. 256 mg/L
Answer and working

C. 1600 mg/L

TDS ≈ 640 × 2.5 = 1600 mg/L. Dividing gives 256; 25 is the approximate total cations in meq/L (10 × EC), not mg/L; 16000 is a decimal slip. The factor varies with salt type (about 550–700).

Question 6 · medium

A crop has a salinity threshold ECe of 2.0 dS/m and a yield decline of 7% per dS/m above it (Maas-Hoffman model). What is the expected relative yield at ECe 5.0 dS/m?

  1. 51%
  2. 65%
  3. 21%
  4. 79%
Answer and working

D. 79%

Relative yield = 100 − b(ECe − a) = 100 − 7 × (5.0 − 2.0) = 79%. Ignoring the threshold gives 65%; 21% is the yield loss, not the yield; adding the threshold gives 51%.

Question 7 · easy

In the SAR formula, concentrations of Na⁺, Ca²⁺ and Mg²⁺ must be expressed in:

  1. percent of CEC
  2. g/kg of soil
  3. meq/L (mmolc/L)
  4. mg/L (ppm)
Answer and working

C. meq/L (mmolc/L)

SAR = Na/√((Ca + Mg)/2) uses milliequivalents per litre of the water or extract. Using mg/L is the commonest error; g/kg and percent of CEC describe exchangeable quantities on the soil, which belong in ESP, not SAR.

Question 8 · medium

A sodic soil with GR 7.75 t/ha of pure gypsum is to be reclaimed with agricultural gypsum of 80% purity. How much product is needed?

  1. 9.30 t/ha
  2. 9.69 t/ha
  3. 7.75 t/ha
  4. 6.20 t/ha
Answer and working

B. 9.69 t/ha

Product = 7.75/0.80 = 9.69 t/ha. Multiplying by purity gives 6.20, the common slip; 7.75 ignores purity; multiplying by 1.2 treats 80% purity as a 20% surcharge.

Question 9 · hard

An acid soil has 2 cmol(+)/kg of exchangeable acidity to be neutralised in the top 15 cm, bulk density 1.3 g/cm³. How much pure CaCO₃ (equivalent weight 50 g/eq) is required per hectare?

  1. 2.25 t/ha
  2. 3.90 t/ha
  3. 0.195 t/ha
  4. 1.95 t/ha
Answer and working

D. 1.95 t/ha

2 cmol(+)/kg = 0.02 eq/kg; CaCO₃ = 0.02 × 50 = 1.0 g/kg. Soil mass = 10,000 × 0.15 × 1,300 = 1.95 × 10⁶ kg/ha, so lime = 1.95 t/ha. Using the molar mass 100 doubles it; using bulk density 1.5 gives 2.25; treating 2 cmol as 0.002 eq gives the tenfold-low answer.

Question 10 · medium

A laboratory reports a sodic soil as calcareous (free CaCO₃ present). Which amendment option becomes available that would not work in a non-calcareous sodic soil?

  1. Elemental sulphur or sulphuric acid, which dissolve native CaCO₃ to release calcium
  2. Farmyard manure, which improves structure as it decomposes in the surface soil
  3. Calcium chloride, which supplies soluble calcium directly to the exchange complex
  4. Gypsum, which supplies soluble calcium directly to the exchange complex of the soil
Answer and working

A. Elemental sulphur or sulphuric acid, which dissolve native CaCO₃ to release calcium

Acid formers work only where CaCO₃ is present to be dissolved. Calcium chloride, gypsum and organic manures work in both calcareous and non-calcareous sodic soils, so none of them is the option that calcareousness newly makes possible.

A study plan for Soil Science for Engineers in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (43% of the 92 questions): Problem soils: saline, sodic and acid (15, 16%); Soil chemistry: pH and electrical conductivity (14, 15%); Bulk density, particle density and porosity (11, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Sodicity: SAR and ESP (10, 11%); Soil formation and profile (10, 11%); Soil water: field capacity, wilting point and available water (9, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Infiltration (8, 9%); Soil texture and structure (8, 9%); Hydraulic conductivity and Darcy's law (7, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Sodicity: SAR and ESP (3 hard of 10), Problem soils: saline, sodic and acid (4 hard of 15), Soil water: field capacity, wilting point and available water (2 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Infiltration (4 easy of 8); Bulk density, particle density and porosity (5 easy of 11).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Soil Science for Engineers

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.