ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Unit IV names strength of materials with engineering mechanics and soil mechanics. Expect elastic-constant relations, standard SF/BM and deflection results, section modulus, torsion and power, Euler effective lengths, thin-cylinder stresses, principal stresses and the names and applicability of failure theories, often as one-step numericals. Question papers are not published, so emphasis is inferred from the syllabus.
How members carry load: stress, strain, bending, torsion, deflection and buckling, used in machine and structure design.
Our 74 ICAR AIEEA-PG questions in this subject: 27 easy, 30 medium, 17 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
A material has bulk modulus 150 GPa and modulus of rigidity 75 GPa. Its Young's modulus is closest to:
C. 192.9 GPa
E = 9KG/(3K + G) = 9 × 150 × 75/(450 + 75) = 192.9 GPa. Swapping K and G in the denominator gives 270.0 GPa; assuming ν = 0.3 without checking gives 195 GPa. Dropping the factor 9 to 3 (3KG/(3K + G)) gives 64.3 GPa.
A thin sphere's diameter increases by a strain ε_d under internal pressure. Its volumetric strain is:
B. 3ε_d
Volume varies as d³, so for small strains ΔV/V = 3Δd/d. For a cylinder the answer would be 2ε_d + ε_L.
For the same material, length and weight, a hollow circular shaft compared with a solid circular shaft:
B. Transmits more torque at the same maximum shear stress
Shear stress in torsion is zero at the centre and largest at the surface; moving material outward raises J/r for the same area. The hollow shaft is also stiffer (larger J), so it twists less, not more.
For a column fixed at the base and free at the top, the effective length used in Euler's formula is:
C. 2L
The fixed–free column buckles like half of a pinned–pinned column of length 2L, so L_e = 2L and the critical load is a quarter of the pinned–pinned value. L/2 is fixed–fixed; L/√2 is fixed–pinned.
A slender column is pinned at one end and fixed at the other. Compared with the same column pinned at both ends, its Euler load is about:
B. Two times
Fixed–pinned L_e = L/√2, so P_cr ∝ 1/L_e² = 2/L². 1.41 = √2 is the ratio of lengths, not loads.
For the same internal pressure, diameter and allowable stress, the wall thickness needed for a thin sphere compared with a thin cylinder is:
D. Half
Sphere: σ = pD/(4t); cylinder hoop: σ = pD/(2t). For equal σ, t_sphere = t_cylinder/2.
Castigliano's theorem states that the partial derivative of the total strain energy with respect to an applied load gives the:
A. Deflection in the direction of that load
δ_i = ∂U/∂P_i. The derivative with respect to an applied couple gives a rotation (slope), so slope is correct only for a moment, not a force.
A steel shear block (G = 80 GPa) is uniformly stressed in shear to 60 MPa. The strain energy stored per unit volume is:
B. 22.5 kJ/m³
u = τ²/(2G) = 60²/(2 × 80,000) = 0.0225 N·mm/mm³ = 22.5 kJ/m³. Using E instead of G gives 9.0 kJ/m³. Omitting the ½ gives 45.0 kJ/m³, and the solid-shaft factor τ²/(4G) gives 11.25 kJ/m³.
For ductile metals, the failure theory that agrees best with experimental yield data under combined stress is the:
C. Distortion energy theory (von Mises)
Tests on ductile steels and aluminium lie close to the von Mises ellipse. Tresca is close and slightly conservative; Rankine and Saint-Venant fit ductile yielding poorly.
Guest's theory of failure is another name for the:
B. Maximum shear stress theory
Guest's (Tresca's) theory: yield when τ_max = σ_y/2. Saint-Venant's is the maximum principal strain theory; Rankine's is maximum principal stress; von Mises–Hencky is distortion energy.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.