LAISHA
Open Laisha

ICAR AIEEA-PG Fluid Mechanics & Open Channel Hydraulics: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
85written to this exam in this subject
18syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Fluid Mechanics & Open Channel Hydraulics in ICAR AIEEA-PG

Single-answer MCQs on fluid properties and their units, Bernoulli assumptions, coefficients of orifices and mouthpieces, flow-meter coefficients, laminar flow results (f = 64/Re, u_max = 2V), minor-loss formulas, maximum power transmission, weir and notch formulas, best channel sections and dimensionless numbers, with short calculations.

Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.

Our 85 ICAR AIEEA-PG questions in this subject: 32 easy, 50 medium, 3 hard, across 18 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

A vertical rectangular sluice gate 1.5 m wide and 2 m high has its top edge 1 m below the water surface. What is the total hydrostatic force on one face of the gate?

  1. 58.9 kN
  2. 44.1 kN
  3. 88.3 kN
  4. 29.4 kN
Answer and working

A. 58.9 kN

F = ρ g A h̄, with h̄ the depth of the centroid = 1 + 2/2 = 2 m. F = 1000 × 9.81 × 3 × 2 = 58860 N ≈ 58.9 kN. Using the top-edge depth gives 29.4 kN and the bottom-edge depth 88.3 kN. 44.1 kN takes the centroid depth as 1.5 m (the gate width) instead of 2 m.

Question 2 · medium

A 400 mm main carrying water at 2.0 m/s divides into two branches. One branch is 250 mm in diameter with a velocity of 2.5 m/s. What is the velocity in the other branch, which is 200 mm in diameter?

  1. 0.875 m/s
  2. 8.00 m/s
  3. 4.09 m/s
  4. 1.02 m/s
Answer and working

C. 4.09 m/s

Q₀ = π(0.4)²/4 × 2.0 = 0.251 m³/s; Q₁ = π(0.25)²/4 × 2.5 = 0.123 m³/s; Q₂ = Q₀ − Q₁ = 0.129 m³/s. V₂ = 0.129/(π × 0.2²/4) = 4.09 m/s. Sending the whole flow into the 200 mm branch gives 8.00 m/s; working with diameters instead of areas gives 0.875 m/s. 1.02 m/s divides the branch flow by the area of the 400 mm main.

Question 3 · easy

Water issues from a small orifice 5 m below the free surface of a large open tank. Neglecting losses, what is the jet velocity?

  1. 7.00 m/s
  2. 98.1 m/s
  3. 49.1 m/s
  4. 9.90 m/s
Answer and working

D. 9.90 m/s

Torricelli's theorem: V = √(2gH) = √(2 × 9.81 × 5) = 9.90 m/s. 7.00 m/s drops the 2, and 98.1 forgets the square root. 49.1 m/s drops both the 2 and the square root (9.81 × 5).

Question 4 · easy

A jet strikes a single flat plate moving in the direction of the jet. At what plate speed u (jet speed V) is the efficiency maximum, and what is that maximum?

  1. u = V/3; 50 %
  2. u = V/2; 50 %
  3. u = V/3; 8/27 (about 29.6 %)
  4. u = V/2; 8/27 (about 29.6 %)
Answer and working

C. u = V/3; 8/27 (about 29.6 %)

Power = ρa(V − u)²u; efficiency = 2(V − u)²u/V³, which is maximum when d/du = 0, giving u = V/3 and η = 8/27. The 50 % at u = V/2 applies to a series of flat plates, where the full jet is used.

Question 5 · medium

Water flows at 40 L/s through 400 m of 200 mm pipe. Taking the Darcy friction factor as 0.018, what is the friction head loss?

  1. 1.83 m
  2. 2.97 m
  3. 0.744 m
  4. 11.9 m
Answer and working

B. 2.97 m

V = 0.04/(π × 0.2²/4) = 1.27 m/s. h_f = f(L/D)V²/2g = 0.018 × 2000 × 1.27²/19.62 = 2.97 m. Treating 0.018 as a Fanning coefficient in 4fLV²/2gD gives 11.9 m. 1.83 m takes the area as D² (V = 1.00 m/s); 0.744 m divides f by 4.

Question 6 · medium

Estimate the Darcy friction factor for flow in a hydraulically smooth plastic pipe at Re = 50 000 using the Blasius equation.

  1. 0.0211
  2. 0.00141
  3. 0.00128
  4. 0.00528
Answer and working

A. 0.0211

Blasius, valid for smooth pipes up to about Re = 10⁵: f = 0.316/Re^0.25 = 0.316/50 000^0.25 = 0.316/15.0 = 0.0211. 64/Re is laminar only; dividing by 4 gives the Fanning value. 0.00128 is 64/Re; 0.00141 takes a square root of Re instead of the fourth root; 0.00528 is the Fanning value (÷ 4).

Question 7 · easy

What is the typical coefficient of discharge of an external cylindrical mouthpiece running full?

  1. About 0.855
  2. About 1.0
  3. About 0.62
  4. About 0.50
Answer and working

A. About 0.855

The jet contracts inside the mouthpiece and then expands to fill it, so it leaves with no contraction; the low pressure at the internal vena contracta draws more flow than a plain orifice (about 0.62). 0.50 is a Borda mouthpiece running free; about 1.0 is an ideal convergent-divergent mouthpiece.

Question 8 · easy

What side slope does a Cipolletti (trapezoidal) weir have, and why?

  1. Vertical sides, so the Francis formula applies without correction
  2. 1 horizontal to 4 vertical, to compensate for the reduction in discharge caused by end contractions
  3. 4 horizontal to 1 vertical, to increase the head for small flows
  4. 1 horizontal to 1 vertical, to make the weir self-cleaning
Answer and working

B. 1 horizontal to 4 vertical, to compensate for the reduction in discharge caused by end contractions

The extra flow through the two triangular side portions of a 1H:4V trapezoid offsets the loss from end contractions, so the discharge can be computed as for a suppressed rectangular weir, Q ≈ 1.86 L H^1.5 (SI).

Question 9 · easy

For the most economical rectangular channel section, what is the relation between bed width b and flow depth y?

  1. b = y
  2. b = 2y
  3. b = y/2
  4. b = 4y
Answer and working

B. b = 2y

Minimising wetted perimeter P = A/y + 2y for fixed area A gives dP/dy = −A/y² + 2 = 0, so A = 2y² and b = 2y. The hydraulic radius is then y/2.

Question 10 · medium

In a 1:36 Froude model of a canal fall, a flood wave takes 1 minute to pass through the model. How long does it take in the prototype?

  1. 216 minutes
  2. 36 minutes
  3. 1 minute
  4. 6 minutes
Answer and working

D. 6 minutes

Under Froude similarity T_r = L_r^0.5 = √36 = 6, so 1 min in the model is 6 min in the prototype. 36 would be the length ratio and 216 = 36^1.5 has no meaning here.

A study plan for Fluid Mechanics & Open Channel Hydraulics in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (44% of the 85 questions): Properties of fluids (7, 8%); Bernoulli's equation: venturimeter, orifice meter and pitot tube (6, 7%); Dimensional analysis and similitude (6, 7%); Forces on submerged surfaces and buoyancy (6, 7%); Hydrostatics and manometry (6, 7%); Orifices, mouthpieces and tank emptying (6, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Weirs and notches (6, 7%); Darcy-Weisbach equation and Moody diagram (5, 6%); Laminar and turbulent flow in pipes (5, 6%); Most economical channel section (5, 6%); Continuity equation (4, 5%); Hydraulic jump (4, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Minor losses (4, 5%); Pipes in series and parallel (4, 5%); Momentum equation (3, 4%); Specific energy and critical depth (3, 4%); Uniform flow in open channels: Manning and Chezy (3, 4%); Hazen-Williams equation (2, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Forces on submerged surfaces and buoyancy (2 hard of 6), Orifices, mouthpieces and tank emptying (1 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Specific energy and critical depth (2 easy of 3); Bernoulli's equation: venturimeter, orifice meter and pitot tube (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Fluid Mechanics & Open Channel Hydraulics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.