ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Single-answer MCQs mixing definitions (types of bearings, contour characteristics, plane-table methods, theodolite axes, levelling terms) with quick calculations (back bearings, RLs, areas and volumes).
Measuring land, levels and volumes, from chain survey to total station and GNSS, and designing land grading.
Our 109 ICAR AIEEA-PG questions in this subject: 43 easy, 46 medium, 20 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
In a prismatic compass, the zero of the graduated ring is placed at the south end because
A. sighting is through a prism opposite the object, so a north sight must read 0° at that end
The ring is fixed to the needle and read through the prism at the eye end, diametrically opposite the object vane; to read 0° on a northward sight the zero must sit at the south end, and the figures are written inverted to read correctly through the prism. It reads whole-circle, not quadrantal, bearings, and its ring does not rotate with the sight (that is the surveyor's compass).
Which method of orienting a plane table is the more accurate?
A. Back-sighting along a previously drawn line
Back-sighting relies on a line already plotted, so it is as accurate as the plotting. The trough compass is quick but subject to local attraction and needle errors, so it is used only where no back station is available.
A point on which both a foresight and a backsight are taken in a levelling line is called a
C. change point
At a change (turning) point the foresight closes one set-up and the backsight opens the next, carrying the RL forward. A benchmark has a known RL; an intermediate station has only one reading.
Which indirect method of contouring is most suitable for a long narrow strip such as a canal alignment?
B. Cross-sections at intervals along the centre line
For a route the ground is profiled along the centre line and cross-sectioned at regular chainages, which directly gives the data for earthwork. Grids suit compact areas; radial tacheometry suits hilly country.
A vernier theodolite has main-scale divisions of 20 minutes and 60 vernier divisions. What is its least count?
C. 20 seconds
Least count = value of one main-scale division / number of vernier divisions = 20′/60 = 1/3′ = 20″.
Taking the mean of face-left and face-right observations of a horizontal angle eliminates all of the following EXCEPT
D. error due to the vertical axis not being truly vertical
Face changes reverse the sign of collimation, trunnion-axis and index errors, so they cancel in the mean. A tilted vertical axis tilts the horizontal axis the same way on both faces, so it does not cancel; careful levelling is the only remedy.
The transit rule for balancing a traverse is preferred over Bowditch's rule when
D. angles are measured more precisely than distances
The transit rule distributes corrections in proportion to the size of each latitude and departure, which assumes angles are good and lengths poorer (theodolite with tape). Bowditch assumes equal effect of angular and linear errors and is the usual rule for compass traverses. Neither can be applied to an open traverse.
A 40 m long prismoid has end areas 12.0 and 24.0 m² and a mid-section area (computed from the mid-depth) of 17.5 m². What is its volume?
B. 706.7 m³
V = (L/6)(A1 + 4Am + A2) = (40/6)(12 + 70 + 24) = 706.7 m³. Average end area gives 720.0 m³ (an overestimate for a prismoid); using L/3 doubles the answer because L here is the full length. 1413.3 m³ uses L/3; 700.0 m³ multiplies the mid-section area by the length.
When is the plane method of land-grading design NOT the best choice?
A. On fields so irregular that a single plane would require excessive earth movement
A single best-fit plane is efficient for fairly uniform fields; where the surface is strongly irregular, profile, plan-inspection or contour-adjustment methods allow varying grades and cut far less earth.
In a two-peg test with pegs A and B 80 m apart, a level set midway reads 1.625 m on A and 1.405 m on B. Set close to A, it reads 1.540 m on A and 1.340 m on B. What is the collimation error and the direction of the line of sight?
A. 0.020 m in 80 m, inclined upwards
From the midway set-up the errors cancel, so the true difference is 1.625 − 1.405 = 0.220 m (B higher). From near A, the correct reading on B should be 1.540 − 0.220 = 1.320 m; the observed 1.340 m is 0.020 m too high over 80 m (0.00025 m/m). A reading too high at the far staff means the line of sight rises above horizontal, i.e. inclined upwards.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.