LAISHA
Open Laisha

ICAR AIEEA-PG Soil Mechanics: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
80written to this exam in this subject
11syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Soil Mechanics in ICAR AIEEA-PG

Single-answer MCQs mixing definitions and short calculations: classification symbols and limits, Proctor test details, zero-air-voids line, consolidation time factors, cu = qu/2, Ka and Kp, the failure-plane angle, and Terzaghi bearing capacity terms.

Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.

Our 80 ICAR AIEEA-PG questions in this subject: 41 easy, 33 medium, 6 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

A soil has a void ratio of 0.80. What is its porosity?

  1. 0.556
  2. 1.250
  3. 0.444
  4. 4.000
Answer and working

C. 0.444

n = e/(1 + e) = 0.80/1.80 = 0.444. 0.556 is 1/(1 + e), the volume fraction of solids, not voids; 1.250 is 1/e; 4.000 comes from wrongly using e/(1 − e). Porosity can never exceed 1.

Question 2 · easy

A moist soil sample weighs 185 g and 160 g after oven-drying at 105–110 °C. What is its water content?

  1. 13.5%
  2. 86.5%
  3. 115.6%
  4. 15.6%
Answer and working

D. 15.6%

Water content is on the dry-mass basis: w = Mw/Ms = (185 − 160)/160 = 25/160 = 15.6%. Dividing by the moist mass (25/185 = 13.5%) is the commonest slip. 86.5% is dry mass over moist mass (160/185), and 115.6% is moist over dry (185/160).

Question 3 · medium

A partly saturated soil has a void ratio of 0.70 and a degree of saturation of 80%. What is its percentage air voids (volume of air as a percentage of total volume)?

  1. 20.0%
  2. 14.0%
  3. 32.9%
  4. 8.2%
Answer and working

D. 8.2%

n = e/(1 + e) = 0.70/1.70 = 0.4118. Air content ac = 1 − S = 0.20 (air as a fraction of voids). Percentage air voids na = n·ac = 0.4118 × 0.20 = 8.2%. 20% is the air content, referred to voids not total volume; 14.0% uses e in place of n; 32.9% is the water volume fraction.

Question 4 · medium

A sand deposit has a water table 3 m below ground. Above it the sand's unit weight is 17 kN/m³; below it the saturated unit weight is 19.5 kN/m³. With γw = 9.81 kN/m³, what is the vertical effective stress at 8 m depth?

  1. 148.50 kPa
  2. 106.95 kPa
  3. 70.02 kPa
  4. 99.45 kPa
Answer and working

D. 99.45 kPa

σ = 17 × 3 + 19.5 × 5 = 148.5 kPa. u = 9.81 × 5 = 49.05 kPa (water depth is 5 m, not 8 m). σ′ = 99.45 kPa. Measuring u from the ground surface gives 70.02; using γsat above the water table gives 106.95.

Question 5 · medium

A light compaction test uses a 2.6 kg rammer falling 310 mm, 25 blows per layer, 3 layers, in a 1000 cm³ mould. What is the compactive energy per unit volume?

  1. 593 kJ/m³
  2. 198 kJ/m³
  3. 60.4 kJ/m³
  4. 2700 kJ/m³
Answer and working

A. 593 kJ/m³

E = blows × layers × rammer weight × drop/volume = 25 × 3 × (2.6 × 9.81) N × 0.31 m/(1 × 10⁻³ m³) = 593014 J/m³ ≈ 593 kJ/m³, close to the 600 kJ/m³ of the standard Proctor test. 198 counts only one layer; 60.4 forgets g (mass instead of weight); 2700 kJ/m³ is the modified (heavy) test.

Question 6 · medium

A normally consolidated clay layer 4 m thick has e0 = 1.10 and Cc = 0.36. At mid-depth the effective overburden stress is 60 kPa, and a new building adds 40 kPa there. What is the primary consolidation settlement?

  1. 152 mm
  2. 350 mm
  3. 319 mm
  4. 290 mm
Answer and working

A. 152 mm

S = [Cc·H/(1 + e0)]·log10[(σ′0 + Δσ′)/σ′0] = (0.36 × 4/2.10) × log10(100/60) = 0.6857 × 0.2218 = 0.1521 m ≈ 152 mm. Using natural log gives 350 mm; leaving out (1 + e0) gives 319 mm; dividing by e0 instead of (1 + e0) gives 290 mm.

Question 7 · easy

A 2 m × 2 m footing carries 400 kN. Using the 2:1 load-spread method, what is the vertical stress increase at 3 m below the footing base?

  1. 32.7 kPa
  2. 6.3 kPa
  3. 100.0 kPa
  4. 16.0 kPa
Answer and working

D. 16.0 kPa

The load spreads at 1 horizontal to 2 vertical, adding z/2 on each side, so the loaded area at depth z is (B + z)(L + z) = 5 × 5 = 25 m². Δσ = 400/25 = 16.0 kPa. Adding only z/2 in total gives (2 + 1.5)² and 32.7 kPa; 100 kPa is the contact pressure. 6.3 kPa spreads at 1:1 instead of 2:1, giving (2 + 6)² = 64 m².

Question 8 · medium

A consolidated drained triaxial test on a dense sand (c′ = 0, φ′ = 34°) is run at a cell pressure of 100 kPa. What deviator stress is reached at failure?

  1. 353.7 kPa
  2. 88.1 kPa
  3. 253.7 kPa
  4. 28.3 kPa
Answer and working

C. 253.7 kPa

σ′1 = σ′3·tan²(45° + φ′/2) = 100 × tan²62° = 100 × 3.537 = 353.7 kPa. Deviator stress = σ′1 − σ′3 = 253.7 kPa. 353.7 kPa is σ1 itself, not the deviator; forgetting to square the tangent gives 88.1 kPa. 28.3 kPa uses tan²(45° − φ′/2), the active ratio (100 × 0.283).

Question 9 · medium

At a point, σ1 = 300 kPa and σ3 = 100 kPa. What are the normal and shear stresses on a plane inclined at 30° to the major principal plane?

  1. σn = 150 kPa, τ = 86.6 kPa
  2. σn = 250 kPa, τ = 86.6 kPa
  3. σn = 250 kPa, τ = 50.0 kPa
  4. σn = 286.6 kPa, τ = 50.0 kPa
Answer and working

B. σn = 250 kPa, τ = 86.6 kPa

σn = (σ1 + σ3)/2 + [(σ1 − σ3)/2]cos2θ = 200 + 100 × cos60° = 250 kPa; τ = [(σ1 − σ3)/2]sin2θ = 100 × sin60° = 86.6 kPa. Using θ instead of 2θ is the usual slip; 150 kPa is the normal stress on a plane at 30° to the minor principal plane.

Question 10 · medium

A smooth vertical wall 5 m high retains level dry sand (γ = 17 kN/m³, φ = 28°) carrying a uniform surcharge of 20 kPa. What is the total Rankine active thrust per metre run?

  1. 112.8 kN/m
  2. 76.7 kN/m
  3. 176.7 kN/m
  4. 94.8 kN/m
Answer and working

A. 112.8 kN/m

Ka = (1 − sin28°)/(1 + sin28°) = 0.3610. Soil thrust = ½KaγH² = 0.5 × 0.3610 × 17 × 25 = 76.7 kN/m (at H/3). Surcharge thrust = Ka·q·H = 0.3610 × 20 × 5 = 36.1 kN/m (uniform pressure, acting at H/2). Total = 112.8 kN/m. Treating the surcharge pressure as triangular halves its share; applying it without Ka overstates it. 176.7 kN/m adds the surcharge without Ka (76.7 + 20 × 5); 94.8 kN/m treats its pressure as triangular (76.7 + ½ × 36.1).

A study plan for Soil Mechanics in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 80 questions): Index properties and soil classification (10, 13%); Phase relations (10, 13%); Bearing capacity basics (8, 10%); Compaction and the Proctor test (8, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Earth pressure: active and passive (Rankine) (8, 10%); Permeability (8, 10%); Terzaghi one-dimensional consolidation (8, 10%); Shear strength and the Mohr-Coulomb criterion (7, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Effective stress (5, 6%); Seepage and flow nets (4, 5%); Slope stability, including infinite slopes (4, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Index properties and soil classification (2 hard of 10), Compaction and the Proctor test (1 hard of 8), Earth pressure: active and passive (Rankine) (1 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Seepage and flow nets (3 easy of 4); Slope stability, including infinite slopes (3 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Soil Mechanics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.