LAISHA
Open Laisha

GATE Soil Mechanics: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
100written to this exam in this subject
11syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Soil Mechanics in GATE

Numerical-answer and MCQ items: phase relations (e, n, S, γd from given masses and volumes), Atterberg indices, constant- and falling-head permeability, equivalent permeability of layered soils, seepage from flow nets and critical gradient, effective stress with a water table, Rankine active thrust with surcharge or water table, and the factor of safety of an infinite slope with and without seepage. Almost all require careful arithmetic and units.

Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.

Our 100 GATE questions in this subject: 34 easy, 42 medium, 24 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

A soil has a bulk unit weight of 19.0 kN/m³, a water content of 12% and G = 2.65. Taking γw = 9.81 kN/m³, what is its degree of saturation?

  1. 0.532
  2. 0.597
  3. 0.318
  4. 0.864
Answer and working

B. 0.597

γd = γ/(1 + w) = 19.0/1.12 = 16.96 kN/m³. e = Gγw/γd − 1 = 2.65 × 9.81/16.96 − 1 = 0.532. S = wG/e = 0.12 × 2.65/0.532 = 0.597. Using the bulk instead of the dry unit weight to find e gives e = 0.368 and S = 0.864; 0.318 is just wG with no division by e.

Question 2 · easy

A sand deposit has an in-situ void ratio of 0.62. Laboratory tests give a maximum void ratio of 0.85 and a minimum void ratio of 0.45. What is its relative density?

  1. 42.5%
  2. 72.9%
  3. 27.1%
  4. 57.5%
Answer and working

D. 57.5%

Dr = (emax − e)/(emax − emin) = (0.85 − 0.62)/(0.85 − 0.45) = 0.23/0.40 = 57.5%, a medium-dense sand. 42.5% comes from putting emin in the numerator, which measures looseness instead of density. 27.1% divides by emax alone (0.23/0.85), and 72.9% is e/emax (0.62/0.85).

Question 3 · hard

In a hydrometer analysis, how long does a spherical particle of diameter 0.01 mm and specific gravity 2.65 take to settle 100 mm in water of viscosity 1.0 × 10⁻³ Pa·s (γw = 9.81 kN/m³)?

  1. 1.85 min
  2. 18.5 min
  3. 11.5 min
  4. 185 min
Answer and working

B. 18.5 min

Stokes' law: v = (γs − γw)D²/(18μ) = (2.65 − 1) × 9810 × (1.0 × 10⁻⁵)²/(18 × 10⁻³) = 8.993e-05 m/s. Time = 0.1/v = 1112 s = 18.5 min. Using γs instead of (γs − γw) ignores buoyancy and gives 11.5 min; the other options are factor-of-ten unit slips.

Question 4 · medium

In a falling-head test, the standpipe area is 1.0 cm², the specimen is 10 cm long with an area of 50 cm², and the head falls from 100 cm to 50 cm in 600 s. What is k?

  1. 1.00e-04 cm/s
  2. 3.33e-04 cm/s
  3. 5.78e-01 cm/s
  4. 2.31e-04 cm/s
Answer and working

D. 2.31e-04 cm/s

k = (aL/(At))·ln(h1/h2) = (1.0 × 10)/(50 × 600) × ln 2 = 3.333e-04 × 0.693 = 2.31e-04 cm/s. Using log10 without the 2.303 factor gives 1.00e-04; swapping the standpipe and specimen areas gives an absurdly high 5.78e-01.

Question 5 · easy

If the compactive effort applied to a soil is increased, how do its maximum dry density and optimum moisture content change?

  1. Both rise
  2. Both fall
  3. Maximum dry density falls; optimum moisture content rises
  4. Maximum dry density rises; optimum moisture content falls
Answer and working

D. Maximum dry density rises; optimum moisture content falls

More energy packs the grains more closely with less water needed for lubrication, so the curve moves up and to the left. This is why the modified Proctor test gives a higher maximum dry density at a lower optimum than the standard test.

Question 6 · hard

A soil (G = 2.70) has a standard Proctor maximum dry unit weight of 17.5 kN/m³ at an optimum moisture content of 16%. With γw = 9.81 kN/m³, what is the percentage air voids at optimum?

  1. 15.9%
  2. 8.2%
  3. 5.4%
  4. 84.1%
Answer and working

C. 5.4%

e = Gγw/γd − 1 = 2.70 × 9.81/17.5 − 1 = 0.5135. S = wG/e = 0.16 × 2.70/0.5135 = 0.841. n = e/(1 + e) = 0.3393. na = n(1 − S) = 5.4%, within the few-per-cent range typical at optimum. 15.9% is air content (fraction of voids), not air voids (fraction of total volume). 8.2% uses e instead of n (0.5135 × 0.159); 84.1% is the degree of saturation.

Question 7 · easy

Which assumption underlies Rankine's earth pressure theory?

  1. Wall friction equals the soil friction angle
  2. The failure surface is a logarithmic spiral
  3. The backfill is always cohesive
  4. The back of the wall is vertical and perfectly smooth
Answer and working

D. The back of the wall is vertical and perfectly smooth

Rankine assumed a smooth vertical wall so that the stresses in a semi-infinite soil mass in plastic equilibrium apply directly. Wall friction is included in Coulomb's wedge theory; the log-spiral surface is used in more refined passive calculations.

Question 8 · easy

What is the steepest slope angle for a long, dry cohesionless embankment face (φ′ = 35°) if a factor of safety of 1.5 is required?

  1. 23.3°
  2. 35.0°
  3. 25.0°
  4. 46.4°
Answer and working

C. 25.0°

F = tanφ′/tanβ, so tanβ = tan35°/1.5 = 0.4668 and β = 25.0°. Dividing the angle directly (35/1.5 = 23.3°) is not the same because tan is not linear. 35° gives F = 1. 46.4° multiplies tanφ′ by 1.5 instead of dividing.

Question 9 · medium

A plate load test with a 0.3 m square plate on a deep, uniform dense sand gives an ultimate bearing pressure of 400 kPa. By the usual plate-load relation for sand, what is the ultimate bearing capacity of a 1.5 m square footing at the same level?

  1. 2000 kPa
  2. 400 kPa
  3. 80 kPa
  4. 10000 kPa
Answer and working

A. 2000 kPa

For sand the ultimate capacity from the γBNγ term is proportional to width: qf = qp × Bf/Bp = 400 × 1.5/0.3 = 2000 kPa. 400 kPa (no scaling) applies to clays, where capacity does not depend on width. The test reflects only soil within about twice the plate width, so deeper weak layers must be checked separately. 80 kPa inverts the width ratio (400 × 0.3/1.5), and 10000 kPa squares it (400 × 25).

Question 10 · easy

How does compaction differ from consolidation?

  1. Both expel water only
  2. Compaction slowly expels pore water under a sustained static load; consolidation expels air quickly by rolling or ramming the soil
  3. They are two names for the same process
  4. Compaction expels air quickly by mechanical energy; consolidation slowly expels water from saturated soil under sustained load
Answer and working

D. Compaction expels air quickly by mechanical energy; consolidation slowly expels water from saturated soil under sustained load

Compaction is a rapid densification of partly saturated soil by rolling, tamping or vibration that reduces air voids. Consolidation is the gradual volume decrease of a saturated soil as pore water drains under a sustained load, governed by permeability.

A study plan for Soil Mechanics in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 100 questions): Terzaghi one-dimensional consolidation (12, 12%); Earth pressure: active and passive (Rankine) (10, 10%); Permeability (10, 10%); Shear strength and the Mohr-Coulomb criterion (10, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Bearing capacity basics (9, 9%); Phase relations (9, 9%); Slope stability, including infinite slopes (9, 9%); Compaction and the Proctor test (8, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Effective stress (8, 8%); Index properties and soil classification (8, 8%); Seepage and flow nets (7, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Effective stress (3 hard of 8), Bearing capacity basics (3 hard of 9), Slope stability, including infinite slopes (3 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Phase relations (5 easy of 9); Seepage and flow nets (3 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Soil Mechanics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.