LAISHA
Open Laisha

GATE Mechanics of Tillage & Traction (Soil Dynamics): practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
68written to this exam in this subject
13syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanics of Tillage & Traction (Soil Dynamics) in GATE

Numerical questions on wheel slip (from speeds, revolutions or distances), rolling radius, tractive efficiency, net traction and gross traction, maximum thrust on sand (W tan φ), weight transfer (P·h/L), front-axle reaction and CG location, overturning angles. Many are NAT questions: keep units and ratios straight.

How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.

Our 68 GATE questions in this subject: 30 easy, 26 medium, 12 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · easy

A soil has cohesion 15 kPa and angle of internal friction 25°. What is its shear strength on a plane carrying a normal stress of 100 kPa?

  1. 46.6 kPa
  2. 57.3 kPa
  3. 61.6 kPa
  4. 105.6 kPa
Answer and working

C. 61.6 kPa

τ = c + σ tan φ = 15 + 100 × tan 25° = 15 + 46.6 = 61.6 kPa. Leaving out cohesion gives 46.6 kPa; using sin φ instead of tan φ gives 57.3 kPa. 105.6 kPa uses cos φ instead of tan φ.

Question 2 · medium

For a cohesive soil, how does adhesion to a steel tool usually change as moisture content rises from dry to very wet?

  1. It rises to a maximum at intermediate moisture and then falls as a water film lubricates the interface
  2. It falls steadily from its highest value in dry soil, because water always weakens the bond between clay and steel
  3. It stays constant because adhesion depends only on clay mineral type
  4. It rises steadily and is highest in saturated soil
Answer and working

A. It rises to a maximum at intermediate moisture and then falls as a water film lubricates the interface

Dry soil has little stickiness; adhesion rises with moisture as water bridges form, then falls when a free water film separates soil from steel. This is why sticky clays cause build-up at intermediate moisture.

Question 3 · medium

In moist plastic soil, the draft of a tine recorded against time is smooth and continuous, while in dry friable soil it shows a repeating saw-tooth pattern. What does the saw-tooth indicate?

  1. Flow failure of the soil around the tool
  2. Resonance of the tractor drawbar
  3. Wheel slip changing the tool depth
  4. Successive shear failure of soil blocks ahead of the tool
Answer and working

D. Successive shear failure of soil blocks ahead of the tool

In brittle soil, force builds as a block is compressed, drops when it shears away, and builds again: a saw-tooth. Flow failure in plastic soil gives a smoother trace.

Question 4 · medium

Why does tractive efficiency pass through a maximum as slip rises?

  1. Rolling resistance falls to zero at the optimum slip, so all axle power reaches the drawbar there
  2. Gross traction becomes negative at high slip
  3. Engine power falls as slip rises
  4. Net traction rises quickly then levels off, while the speed loss grows in proportion to slip
Answer and working

D. Net traction rises quickly then levels off, while the speed loss grows in proportion to slip

At zero slip, net traction and TE are zero. NT/GT rises steeply then saturates as soil strength is mobilised, while (1 − s) falls steadily; their product peaks.

Question 5 · easy

A standard cone of base area 323 mm² needs a force of 450 N to penetrate soil at the standard rate. What is the cone index?

  1. 1393 kPa
  2. 1.39 kPa
  3. 1393189 kPa
  4. 3462 kPa
Answer and working

A. 1393 kPa

CI = F/A = 450 N / 323 × 10⁻⁶ m² = 1393189 Pa ≈ 1393 kPa (1.39 MPa). Dividing by mm² directly gives MPa-scale numbers in the wrong unit; using the small cone's area gives 3462 kPa.

Question 6 · easy

Weight transfer from the front to the rear axle of a pulling tractor increases when

  1. the wheelbase is lengthened
  2. the drawbar pull is reduced
  3. extra front ballast is added
  4. the hitch height is raised
Answer and working

D. the hitch height is raised

ΔW = P·h/L: higher hitch or higher pull increases transfer; a longer wheelbase reduces it. Front ballast raises the front load but does not change the amount transferred.

Question 7 · medium

A tractor with a rigid front axle has track width 1.6 m and CG 0.9 m above ground, midway between the wheels. What is the static side slope at which it begins to overturn?

  1. 60.6°
  2. 41.6°
  3. 48.4°
  4. 62.7°
Answer and working

B. 41.6°

tan θ = (t/2)/h = 0.8/0.9 = 0.889 → θ = 41.6°. Using the full track gives 60.6°, which overstates stability. 48.4° inverts the ratio; 62.7° uses sin⁻¹ instead of tan⁻¹.

Question 8 · hard

A tractor of weight 30 kN, wheelbase 2.2 m, has a level front reaction of 9.0 kN. With the front raised 20° (rear wheels on the ground) the front reads 7.5 kN. The axle centres are level on level ground at 0.7 m height. How high is the CG above the ground?

  1. 0.30 m
  2. 1.00 m
  3. 1.02 m
  4. 0.82 m
Answer and working

B. 1.00 m

y above the axle line = (Wf − Wf′)L/(W tan θ) = (9.0 − 7.5) × 2.2/(30 × tan 20°) = 3.30/10.919 = 0.302 m. Height above ground = 0.7 + 0.302 = 1.00 m. Stopping at y forgets the axle height; using sin θ or cos θ uses the wrong trigonometric function. 0.30 m stops at y; 1.02 m uses sin θ; 0.82 m uses cos θ.

Question 9 · easy

When taking moments about the rear wheel contact point of a tractor on level ground, why do the front wheel rolling resistance and rear wheel thrust not appear?

  1. They are always negligible compared with weight
  2. They cancel each other exactly
  3. They act at the axle height and cancel exactly with the drawbar pull, so together they contribute no net moment about that point
  4. They act horizontally at ground level, so their lines of action pass through the moment point's level and have zero arm
Answer and working

D. They act horizontally at ground level, so their lines of action pass through the moment point's level and have zero arm

Both forces act at the tyre-soil interface, at ground level, so their moment about a point on the ground is zero. They do enter the horizontal force balance.

Question 10 · medium

According to the widely used conclusion from Söhne's work, subsoil stress under a tyre is governed mainly by

  1. the tyre inflation pressure
  2. the tyre tread pattern
  3. the forward travel speed
  4. the total axle load
Answer and working

D. the total axle load

Topsoil stress follows contact (roughly inflation) pressure; deeper stress follows total load. Lower pressure protects topsoil, but only lighter axle loads protect the subsoil.

A study plan for Mechanics of Tillage & Traction (Soil Dynamics) in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 68 questions): Traction theory: slip, rolling resistance and net traction (10, 15%); Longitudinal and lateral stability (6, 9%); Prediction of draft (6, 9%); Tractive efficiency (6, 9%); Tractor chassis mechanics (6, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Wheel and track mechanics (6, 9%); Determination of the centre of gravity (5, 7%); Weight transfer (5, 7%); Dynamic properties and strength of soil (4, 6%); Soil compaction by vehicles (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Soil-tool mechanics (4, 6%); Cone index and cone penetrometer (3, 4%); Traction in wetland soils (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Determination of the centre of gravity (2 hard of 5), Weight transfer (2 hard of 5), Longitudinal and lateral stability (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Dynamic properties and strength of soil (3 easy of 4); Cone index and cone penetrometer (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Mechanics of Tillage & Traction (Soil Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.