Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission
Original practice questions written to the published syllabus · not past papersRajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.
Source: rpsc.rajasthan.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Traction and CG determination named in the farm power syllabus; direct formula questions.
How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.
Our 29 Rajasthan PSC questions in this subject: 24 easy, 5 medium, 0 hard, across 13 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Rajasthan PSC and are not shown on any other exam's page.
In a disc harrow, why are the front gangs set at opposite angles?
B. So that their side forces largely cancel
Each angled gang produces a side force; opposing gangs balance them so the harrow runs straight. Vertical load is still needed for penetration, and draft cannot be zero.
A 3 m wide tine cultivator has a unit draft of 2.5 kN per metre width. It is pulled at 6 km/h. What drawbar power does it need?
A. 12.50 kW
Draft = 2.5 × 3.0 = 7.5 kN. Power = 7.5 × 6/3.6 = 12.50 kW. Using unit draft without multiplying by width gives 4.17 kW. 45.00 kW multiplies by km/h without converting; 4.50 kW divides the draft by the speed (7.5/1.667).
An engine delivers 40 kW; transmission efficiency is 0.90 and tractive efficiency 0.70. What drawbar power is available?
C. 25.2 kW
Drawbar = 40 × 0.9 × 0.7 = 25.2 kW. Ignoring the transmission gives 28.0 kW; dividing gives more than engine power, which is impossible. Dividing gives 63.5 kW; 36.0 kW ignores the tractive efficiency.
A rollover protective structure (ROPS) protects the operator only if
C. the seat belt is worn so the operator stays within the protected zone
In an overturn an unbelted operator can be thrown out and crushed by the ROPS or tractor. ROPS and seat belt work together; a folded ROPS gives no protection.
A level tractor weighs 32 kN in total and its front axle reads 9.6 kN on a platform scale. The wheelbase is 2.4 m. How far ahead of the rear axle is the CG?
A. 0.72 m
Moments about the rear axle: Wf·L = W·x → x = 9.6 × 2.4/32 = 0.72 m. Using the rear reading gives the distance from the front axle, 1.68 m. 0.30 m forgets to multiply by L; 1.03 m divides by the rear reading (22.4 kN) instead of the total.
A tractor with a track width of 1.5 m weighs 28 kN. The right-side wheels carry 14.7 kN. How far is the CG from the left wheel line?
C. 0.787 m
Moments about the left wheel line: W_right × t = W × y → y = 14.7 × 1.5/28 = 0.787 m, slightly right of centre (0.037 m). Using the left reading gives the distance from the right wheel line. 0.713 m uses the left reading; 0.750 m assumes the CG is central; 0.394 m uses half the track.
Of several passes of the same wheel in one track, which usually causes the largest increase in bulk density?
B. The first pass
Most compaction occurs on the first pass; later passes add less each time but push compaction deeper. This is why confining traffic to fewer tracks helps.
The coefficient of rolling resistance of a towed wheel is
D. rolling resistance divided by wheel load
RR/W is a dimensionless coefficient; it is small on firm roads and several times larger on soft or tilled soil.
Which change improves the lateral stability of a tractor working across slopes?
A. Setting the rear wheels to a wider track
Lateral stability depends on half track over CG height. A wider track increases the base; raising loads or removing low ballast raises the CG.
Compared with a wheeled tractor, a crawler tractor of the same weight has
D. a larger contact area and lower mean ground pressure
Tracks spread the load along a long contact length. They still have motion resistance from soil deformation and internal running-gear friction.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.