Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission
Original practice questions written to the published syllabus · not past papersRajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.
Source: rpsc.rajasthan.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Sprayers, weeders, mowers, reapers, combines and threshers: how they work, how to calibrate them and where losses come from.
Our 42 Rajasthan PSC questions in this subject: 32 easy, 8 medium, 2 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Rajasthan PSC and are not shown on any other exam's page.
In a hydraulic sprayer, strainers are made progressively finer from the tank filling opening towards the nozzle so that
D. the smallest opening in the system, the nozzle orifice, does not block
Coarse strainers stop large debris early; the finest strainer is just before the nozzle, which has the smallest orifice. Strainers do not raise pressure; they cause a small pressure drop.
In the field, the sprayer's forward speed for calibration should be found by
B. timing the sprayer over a measured distance in the field to be sprayed
Wheel slip and soft or uneven ground change actual speed, so the reliable value comes from timing a measured run in the field. For example, 100 m in 60 s is 100/60 × 3.6 = 6 km/h.
In a hand-operated rotary duster, the air stream is produced by
A. a fan driven at high speed by a crank through a gear train
The rotary duster uses a crank and step-up gears to spin a fan; the same drive usually turns the hopper agitator. Bellows and plunger dusters are separate types.
On a standard reciprocating cutter bar, the knife stroke, section spacing and guard spacing are each
A. 76.2 mm
The standard cutter bar uses a 3 in (76.2 mm) stroke with sections and guards at 76.2 mm spacing, so each section moves from one guard centre to the next. 50.8 mm (2 in) and 101.6 mm (4 in) are not the standard; 38.1 mm is the crank radius, half the stroke.
A vertical conveyor reaper (VCR)
B. cuts the crop and conveys it upright to one side, laying it in a windrow
The VCR's lugged belts carry the cut stems across and drop them in a windrow at right angles to travel. Binding is done by a reaper-binder; threshing by a combine; stripping by a stripper header.
Loss of grain that has fallen to the ground from over-ripe crop before the harvester arrives is called
D. pre-harvest (shattering) loss
It occurs before any machine action and grows as harvest is delayed. The other losses arise inside the combine.
Of 1000 kg/h of grain fed to a thresher, 8 kg/h leaves still in the heads. The threshing efficiency is
D. 99.2%
Threshing efficiency = 100 − unthreshed % = 100 − (8/1000 × 100) = 99.2%. 0.8% is the unthreshed fraction. 92% subtracts the 8 kg directly from 100; 99.92% divides by 100 instead of 1000 in the unthreshed fraction.
To obtain a shorter length of cut on a chaff cutter at the same flywheel speed, the operator should
D. reduce the feed roll speed through the gearbox
Length of cut = feed speed / cuts per second; slower feed rolls give shorter pieces. Removing a knife would double the length. Wider clearance gives ragged cuts.
In an elevator-type potato digger, soil is separated from tubers mainly by
D. passing the lifted mass over a rod-link elevator that is agitated so loose soil falls through
The share lifts soil and tubers onto the rod-chain elevator; agitators shake soil through the gaps and tubers are dropped on the surface.
The primary extractor fan on a sugarcane harvester
D. removes trash
It removes extraneous matter after chopping; setting its speed trades trash removal against cane loss. The fan blows leaves and trash out of the cane stream.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.