LAISHA
Open Laisha

ICAR AIEEA-PG Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
62written to this exam in this subject
15syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ICAR AIEEA-PG

Parts and functions of sprayers, pumps, nozzles, dusters, weeders, mowers, reapers, combines and threshers; performance terms such as threshing and cleaning efficiency; short calibration and field-capacity calculations.

Sprayers, weeders, mowers, reapers, combines and threshers: how they work, how to calibrate them and where losses come from.

Our 62 ICAR AIEEA-PG questions in this subject: 26 easy, 32 medium, 4 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

A common practical rule for replacing a set of spray nozzles is when their measured flow exceeds that of new nozzles by about

  1. 1 per cent
  2. 50 per cent
  3. 10 per cent
  4. 100 per cent
Answer and working

C. 10 per cent

Worn orifices enlarge; once flow is roughly 10% above new the pattern is also distorted and overdosing is significant. 1% is within measurement error; waiting for 50% would badly overdose.

Question 2 · medium

Which weeding tool is designed to remove weeds within the crop row between plants?

  1. Finger weeder
  2. Duck-foot sweep between rows
  3. Ridger
  4. Rolling cultivator set to throw soil away from the row
Answer and working

A. Finger weeder

Finger weeders have rubber fingers, driven by ground wheels, that reach into the row and flick out small weeds while bending round stronger crop stems. Sweeps work between rows; ridgers heap soil.

Question 3 · medium

Registration of a reciprocating cutter bar is correct when

  1. the guard points lie in a straight line and the knife sections all touch the ledger plates
  2. at each stroke end the knife section centre lines coincide with the guard centre lines
  3. the knife clips just touch the sections
  4. the pitman is in line with the knife
Answer and working

B. at each stroke end the knife section centre lines coincide with the guard centre lines

That is the definition of registration. Straight guard points and parallel knife motion are alignment, a separate adjustment. Poor registration gives uneven cutting and uncut stems.

Question 4 · hard

A reel of 1.0 m diameter must work with a reel index of 1.5 at a forward speed of 4 km/h. The reel speed is about

  1. 21.2 rev/min
  2. 63.7 rev/min
  3. 31.8 rev/min
  4. 0.53 rev/min
Answer and working

C. 31.8 rev/min

Reel peripheral speed = 1.5 × 4/3.6 = 1.667 m/s. N = v × 60/(πD) = 1.667 × 60/(π × 1.0) = 31.8 rev/min. Ignoring the index gives 21.2 rev/min; using radius in πD gives 63.7. 0.53 leaves the answer in rev/s (1.667/π).

Question 5 · easy

The straw walkers of a conventional combine

  1. lift and toss the straw rearward so free grain falls through
  2. thresh the grain from the heads by rubbing it against the concave
  3. blow chaff out of the machine
  4. convey clean grain to the tank
Answer and working

A. lift and toss the straw rearward so free grain falls through

Crank-driven walker sections loosen the straw mat repeatedly; free grain falls through the decks to the grain pan. Threshing happens at the cylinder and air cleaning at the shoe.

Question 6 · easy

Loss counts behind a wheat combine average 50 grains per m², and the thousand-grain weight is 40 g. The loss is

  1. 2 kg/ha
  2. 20 kg/ha
  3. 200 kg/ha
  4. 0.2 kg/ha
Answer and working

B. 20 kg/ha

Loss = 50 × 40/1000 = 2 g/m² = 2 × 10 = 20 kg/ha (kg/ha = grains/m² × TGW/100). The factor of ten slip gives 2 or 200. 0.2 kg/ha is a factor-of-100 slip.

Question 7 · medium

Machine loss (threshing, separating and cleaning) of a combine is obtained from field counts as

  1. total loss behind the machine minus header and pre-harvest losses
  2. header loss minus pre-harvest loss, measured in the standing crop ahead of the machine
  3. total loss plus header loss
  4. pre-harvest loss alone
Answer and working

A. total loss behind the machine minus header and pre-harvest losses

Grain found behind the machine includes what was already on the ground and what the header dropped; subtracting both leaves the loss from the threshing, separating and cleaning units.

Question 8 · medium

A multi-crop axial-flow thresher differs from a conventional throw-in thresher in that

  1. it has no threshing drum, as the crop is threshed by rubbing between two long rotating augers
  2. it cannot thresh wheat
  3. it works without a concave
  4. the crop moves helically along the drum axis, threshing and separating over a long path
Answer and working

D. the crop moves helically along the drum axis, threshing and separating over a long path

Axial movement gives longer residence and separation; different crops are handled by changing speed, concave and sieves.

Question 9 · medium

To reduce bruising on a potato digger elevator, the operator should

  1. run the elevator much faster than forward speed so it is almost empty and tubers do not pile up
  2. increase agitation to maximum
  3. keep the elevator loaded with soil as a cushion and match its speed to forward speed
  4. raise the drop height at the rear
Answer and working

C. keep the elevator loaded with soil as a cushion and match its speed to forward speed

A soil cushion protects tubers; a bare fast-running elevator and high drops cause bruising. Heavy agitation also damages tubers.

Question 10 · medium

Compared with spindle pickers, stripper cotton harvesters

  1. deliver cleaner seed cotton
  2. are selective for open bolls only
  3. work best on tall, bushy plants with many green bolls still unopened
  4. harvest all bolls with more burs and trash, needing extra cleaning
Answer and working

D. harvest all bolls with more burs and trash, needing extra cleaning

Strippers take everything, so field cleaners or burr extractors and more gin cleaning are needed. They suit short, compact plants.

A study plan for Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 62 questions): Nozzles and droplet spectra (8, 13%); Combine harvester: header, threshing cylinder and concave (6, 10%); Sprayers: hydraulic, air-assisted and electrostatic (5, 8%); Weeders and inter-cultivation equipment (5, 8%); Combine separation and cleaning: straw walker and cleaning shoe (4, 6%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Dusters (4, 6%); Harvesting and threshing losses (4, 6%); Mowers: reciprocating and rotary; mechanics of cutting (4, 6%); Reapers (4, 6%); Threshers (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Cotton and sugarcane harvesting (3, 5%); Root-crop diggers (3, 5%); Sprayer calibration and application rate (3, 5%); Straw and residue management machines (3, 5%); Chaff cutters (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Reapers (2 hard of 4), Chaff cutters (1 hard of 2), Threshers (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Sprayer calibration and application rate (3 easy of 3); Dusters (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.