LAISHA
Open Laisha

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10)

India · National Testing Agency for ICAR

3000practice questions written to this syllabus
45subjects

What ICAR AIEEA-PG is

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India.

Format

Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Sections

How it has changed

Admission to M.Tech in agricultural universities and the ICAR-PG scholarship. Sub-subjects for counselling: 10.1 SWCE, 10.2 IDE, 10.3 Processing and Food Engineering, 10.4 FMPE, 10.5 REE. Wider than GATE AG: electric motors (Unit II) and farmstead planning are examined here but not in GATE AG. Question papers are not published, so no topic-frequency data exists. 2026 bulletin: https://cdnbbsr.s3waas.gov.in/s388a839f2f6f1427879fc33ee4acf4f66/uploads/2026/05/202605091397132773.pdf

How to prepare for ICAR AIEEA-PG

Where our 3000 questions for it fall

Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.

  1. Heaviest (45% of the questions): Surveying & Levelling (109); Computer Programming, Data Structures & Agricultural Informatics (108); Engineering Mathematics (105); Engineering Thermodynamics (96); Hydraulic Drives & Controls (94); Soil Science for Engineers (92); Watershed Hydrology (89); Post-Harvest Engineering of Horticultural Crops (88); Machine Design (87); Fluid Mechanics & Open Channel Hydraulics (85); Theory of Machines (83); Soil Mechanics (80); and 3 more.

    Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.

  2. Middle band: Renewable Energy Sources (Solar, Wind) (74); Electrical Machines & Power Utilisation (72); Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) (72); Groundwater, Wells & Pumps (70); Watershed Planning & Management (69); Refrigeration, Air-Conditioning & Cold-Chain Engineering (68); Engineering Properties of Agricultural Produce (67); Water Resources Management, Floods & Canal Systems (66); Engineering Mechanics (Statics & Dynamics) (65); Sprinkler & Micro-Irrigation Systems (65); Farm Power Sources (64); Heat & Mass Transfer (63); and 3 more.

    One pass per subject, then mixed sets across them.

  3. Lighter: Post-Harvest Engineering of Cereals, Pulses & Oilseeds (58); Agricultural Drainage Engineering (57); Tractor Systems & Controls (54); Agricultural Structures & Environmental Control (52); Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser (50); Tractor & Automotive Engines (IC Engines) (50); Mechanics of Tillage & Traction (Soil Dynamics) (49); Farm Machinery Management & Economics (44); Human Engineering, Ergonomics & Safety (43); Food & Dairy Engineering (43); Food Quality, Safety & Process Plant Design (43); Instrumentation, Sensors & Process Control (40); and 3 more.

    Definitions, classifications and standard figures; quick to revise, easy marks to lose.

  4. Hardest share: Building Materials, Theory of Structures & Construction (2 hard of 5), Engineering Mechanics (Statics & Dynamics) (18 hard of 65), Strength of Materials (17 hard of 74).

    Leave untimed time for these and read every explanation, including for the options you rejected.

Official source: icar.org.in

8 practice questions, worked

Original questions written to this exam's published syllabus and pattern. Not past papers.

1. A shaft is specified in AISI/SAE 1045 steel. What does the designation tell the designer?

  1. It is a free-cutting steel with 4.5 per cent sulphur
  2. It is a plain carbon steel with about 0.45 per cent carbon
  3. It is an alloy steel with 10 per cent nickel and 0.45 per cent chromium
  4. It has a tensile strength of about 1045 MPa
Answer and working

B. It is a plain carbon steel with about 0.45 per cent carbon

In the AISI/SAE four-digit system, the first two digits (10) mean plain carbon steel and the last two give carbon content in hundredths of a per cent (45, so about 0.45 per cent). The number is not a strength, and sulphurised free-cutting grades are in the 11xx series.

Machine Design · The design process, materials and factor of safety

2. Which indirect method of contouring is most suitable for a long narrow strip such as a canal alignment?

  1. Radial lines from a single station
  2. Cross-sections at intervals along the centre line
  3. Grid of squares over the whole area
  4. Direct method on every contour
Answer and working

B. Cross-sections at intervals along the centre line

For a route the ground is profiled along the centre line and cross-sectioned at regular chainages, which directly gives the data for earthwork. Grids suit compact areas; radial tacheometry suits hilly country.

Surveying & Levelling · Contouring

3. Why does an induction motor driving a pump operate at a lagging power factor?

  1. It draws magnetising current that lags the voltage by nearly 90°
  2. Its rotor bars behave as capacitors that store charge each half cycle
  3. Its slip makes the rotor frequency higher than the supply frequency
  4. Its stator copper losses shift the current ahead of the supply voltage
Answer and working

A. It draws magnetising current that lags the voltage by nearly 90°

The motor needs a magnetising current to set up the air-gap flux; this component is almost purely inductive and lags the voltage, so the total current lags. Rotor bars are not capacitors, rotor frequency is slip times supply frequency (lower, not higher), and resistive losses keep current in phase rather than shifting it ahead.

Basic Electrical & Electronics Engineering · AC circuits, phasors and power factor

4. Hydrologic soil group A in the SCS curve number method refers to soils with:

  1. very slow infiltration and high runoff potential, such as heavy clays
  2. a high water table that stays near the surface for most of the year
  3. shallow soil over impervious rock
  4. high infiltration rates and low runoff potential, such as deep sands
Answer and working

D. high infiltration rates and low runoff potential, such as deep sands

Group A has the lowest runoff potential. Clays, high water tables and shallow soils over rock are group D.

Watershed Hydrology · Runoff estimation: SCS curve number

5. A steel ball of radius 1.0 mm (density 7800 kg/m³) falls at a steady 8.0 mm/s through honey (density 1400 kg/m³). Using Stokes' law, μ = 2r²g(ρ_s − ρ_f)/(9v), the viscosity of the honey is

  1. 1.74 Pa·s
  2. 6.98 Pa·s
  3. 2.13 Pa·s
  4. 0.436 Pa·s
Answer and working

A. 1.74 Pa·s

μ = 2 × (10⁻³)² × 9.81 × 6400 / (9 × 0.008) = 0.12557/0.072 = 1.74 Pa·s. 6.98 uses the diameter in r²; 2.13 ignores the buoyancy of the honey; 0.436 treats 1.0 mm as the diameter and halves it again.

Engineering Properties of Agricultural Produce · Rheology: Newtonian and non-Newtonian flow

6. What is the purpose of the outer ring in a double-ring infiltrometer?

  1. It measures evaporation from the soil surface during the test for a correction
  2. It buffers lateral spread so the inner ring measures nearly vertical infiltration
  3. It anchors the inner ring so that it is not pushed out by soil swelling
  4. It holds the reserve water used to keep the inner ring at a constant level
Answer and working

B. It buffers lateral spread so the inner ring measures nearly vertical infiltration

Water from the outer ring wets the soil around the inner ring, so water from the inner ring is not drawn sideways and its fall represents one-dimensional vertical infiltration. Readings are taken from the inner ring only. The outer ring is not an evaporation pan, a reservoir or an anchor.

Soil Science for Engineers · Infiltration

7. In a hydraulic (water-brake) dynamometer used for PTO testing, the load on the engine is varied by

  1. changing the current in a coil that sets a magnetic field
  2. tightening a rope or band around a rotating brake drum
  3. changing the gear ratio between the PTO and the rotor
  4. changing the water level in the casing around the rotor
Answer and working

D. changing the water level in the casing around the rotor

A water brake absorbs power by churning water; more water means more resistance. Coil current controls an eddy-current dynamometer, a rope or band is a friction brake, and gear ratio changes do not set dynamometer load.

Farm Machinery Testing, Evaluation & Standards · Test instrumentation: dynamometers and fuel meters

8. Which weeding tool is designed to remove weeds within the crop row between plants?

  1. Finger weeder
  2. Duck-foot sweep between rows
  3. Ridger
  4. Rolling cultivator set to throw soil away from the row
Answer and working

A. Finger weeder

Finger weeders have rubber fingers, driven by ground wheels, that reach into the row and flick out small weeds while bending round stronger crop stems. Sweeps work between rows; ridgers heap soil.

Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing · Weeders and inter-cultivation equipment

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock all 3,000 questions — ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10)

US$10 a month · one price worldwide · cancel any time

  • Every practice question for this course, with explanations
  • Timed papers for the exams this course leads to
  • Ask Laisha to explain any topic — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.