LAISHA
Open Laisha

ICAR AIEEA-PG Heat & Mass Transfer: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
63written to this exam in this subject
12syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Heat & Mass Transfer in ICAR AIEEA-PG

Unit III (thermodynamics) and Unit VI (processing) ask single-answer MCQs: definitions of the dimensionless numbers, units of k, h, α and D, the physical meaning of the Biot and Fourier numbers, critical radius, counterflow versus parallel flow, Kirchhoff's law, black and grey bodies, and simple one-step calculations. Negative marking rewards knowing exact definitions.

Conduction, convection, radiation, heat exchangers and diffusion — the physics of drying, cooling, freezing and cold-store walls.

Our 63 ICAR AIEEA-PG questions in this subject: 31 easy, 32 medium, 0 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

A plane brick wall 0.2 m thick (k = 0.8 W/m·K) has an area of 10 m². Its faces are held at 35 °C and 5 °C. The steady heat flow through the wall is

  1. 1,200 W
  2. 120 W
  3. 12.0 W
  4. 48.0 W
Answer and working

A. 1,200 W

Q = kAΔT/L = 0.8 × 10 × 30 / 0.2 = 1,200 W. 120 W is the flux per square metre (W/m²) mistaken for the total; 12 W comes from entering the thickness as 20 cm instead of 0.2 m; 48 W comes from multiplying by L instead of dividing.

Question 2 · medium

A steam pipe of outer radius 50 mm is covered with insulation (k = 0.05 W/m·K) to an outer radius of 100 mm. The inner and outer surfaces of the insulation are at 150 °C and 30 °C. The heat loss per metre length is closest to

  1. 37.7 W/m
  2. 54.4 W/m
  3. 75.4 W/m
  4. 56.5 W/m
Answer and working

B. 54.4 W/m

For a cylinder Q/L = 2πk(T1 − T2)/ln(r2/r1) = 2π × 0.05 × 120 / ln 2 = 54.4 W/m. Treating the layer as a plane wall of thickness 0.05 m with the inner area gives 37.7, with the outer area 75.4, and with the arithmetic-mean area 56.5 W/m; only the logarithmic-mean area makes the plane-wall formula exact.

Question 3 · medium

A steel ball bearing 10 mm in diameter (k = 40 W/m·K) is cooled in air with h = 100 W/m²·K. The Biot number based on L_c = V/A_s is

  1. 0.0125
  2. 0.00417
  3. 0.025
  4. 240
Answer and working

B. 0.00417

For a sphere L_c = V/A_s = r/3 = 0.005/3 = 0.001667 m. Bi = hL_c/k = 100 × 0.001667/40 = 0.00417, well below 0.1, so the lumped model applies. Using r gives 0.0125; using D gives 0.025; 240 is the inverted ratio.

Question 4 · easy

Adding fins to a heat-exchange surface is most worthwhile when the surface transfers heat to

  1. a boiling liquid
  2. a condensing vapour
  3. a gas with a low convection coefficient
  4. a liquid metal with a very high convection coefficient
Answer and working

C. a gas with a low convection coefficient

Fin effectiveness √(kP/(hA_c)) is large when h is small. Fins are therefore used on the air side of radiators, condensers and engine cylinders. With boiling, condensation or liquid metals, h is so high that the fin's own conduction resistance limits it and effectiveness is poor.

Question 5 · medium

For a straight fin with an insulated tip, mL = 2.0. Its fin efficiency is closest to

  1. 0.482
  2. 0.964
  3. 0.135
  4. 0.333
Answer and working

A. 0.482

η_f = tanh(mL)/(mL) = 0.9640/2 = 0.482. 0.964 is tanh(mL) alone, the ratio of actual heat to that of an infinitely long fin; e^(−mL) = 0.135 is the tip excess-temperature ratio of an infinite fin; 1/(1 + mL) = 0.333 is not a fin relation at all.

Question 6 · easy

Plate heat exchangers are the standard choice for milk pasteurisation mainly because they

  1. can operate at far higher pressures than shell-and-tube exchangers, which is needed to keep milk liquid at pasteurising temperature
  2. give high heat-transfer coefficients in a compact unit, are easy to clean, and allow regeneration between hot and cold milk
  3. need no gaskets and so never leak
  4. work only in parallel flow, which protects milk from overheating
Answer and working

B. give high heat-transfer coefficients in a compact unit, are easy to clean, and allow regeneration between hot and cold milk

Corrugated plates promote turbulence at modest velocity, giving high U; the pack can be opened for inspection and cleaned in place; and sections can be arranged for regeneration, where outgoing pasteurised milk heats incoming raw milk. Gasketed plate exchangers have pressure limits below shell-and-tube units, and they are normally run in counterflow.

Question 7 · medium

The maximum possible heat-transfer rate used in defining heat-exchanger effectiveness is

  1. C_min(T_h,in − T_c,in)
  2. C_max(T_h,in − T_c,in)
  3. C_min(T_h,in − T_h,out)
  4. UA × LMTD
Answer and working

A. C_min(T_h,in − T_c,in)

Only the fluid with the smaller heat-capacity rate can undergo the full temperature difference between the two inlets, which it would do in an infinitely long counterflow exchanger. Using C_max would require the other fluid to change temperature by more than the inlet difference, which violates the second law. UA × LMTD is the actual rate, not the maximum.

Question 8 · medium

On the pool-boiling curve, the Leidenfrost point is

  1. the point of maximum (critical) heat flux
  2. the point of minimum heat flux between transition and film boiling
  3. the onset of nucleate boiling
  4. the point where natural convection begins
Answer and working

B. the point of minimum heat flux between transition and film boiling

The Leidenfrost point marks the minimum heat flux, where a stable vapour film first covers the surface; water drops skittering on a very hot plate show it. The maximum is the critical heat flux at the end of nucleate boiling.

Question 9 · easy

The Sherwood number, Sh = h_m L/D_AB, is the mass-transfer analogue of the

  1. Prandtl number
  2. Nusselt number
  3. Reynolds number
  4. Biot number
Answer and working

B. Nusselt number

Sh is the dimensionless convective mass-transfer coefficient, as Nu is for heat. The Schmidt number Sc = ν/D is the analogue of Pr; the mass-transfer Biot number h_m L/D_solid uses the diffusivity inside the solid.

Question 10 · medium

The Page thin-layer drying model is written as

  1. MR = exp(−k t)
  2. MR = exp(−k tⁿ)
  3. MR = a exp(−k t)
  4. MR = (8/π²) exp(−π²D t/(4L²))
Answer and working

B. MR = exp(−k tⁿ)

The Page model adds an empirical exponent n to the Lewis (Newton) model MR = exp(−kt). MR = a·exp(−kt) is the Henderson–Pabis model, and the last form is the first term of the diffusion solution for a slab.

A study plan for Heat & Mass Transfer in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (43% of the 63 questions): Convection and dimensionless numbers (Nu, Re, Pr) (9, 14%); Composite walls and critical radius of insulation (6, 10%); Extended surfaces (fins) (6, 10%); Radiation: Stefan-Boltzmann law and view factors (6, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Steady conduction through plane walls and cylinders (6, 10%); Diffusive mass transfer and Fick's law (5, 8%); Heat exchangers: LMTD method (5, 8%); Simultaneous heat and mass transfer in drying (5, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Transient conduction: lumped capacity and Heisler charts (5, 8%); Heat exchangers: effectiveness-NTU method (4, 6%); Condensation and boiling (3, 5%); Convective mass transfer (3, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Steady conduction through plane walls and cylinders (4 easy of 6); Condensation and boiling (2 easy of 3).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.