LAISHA
Open Laisha

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus Heat & Mass Transfer: practice questions

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus · Canada · Provincial and territorial regulators (syllabus by Engineers Canada)

Original practice questions written to the published syllabus · not past papers
10worked here, free
37written to this exam in this subject
12syllabus units

About Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus is a licensing and registration exam run by Provincial and territorial regulators (syllabus by Engineers Canada), for candidates in Canada. Written confirmatory exams for graduates of non-CEAB programmes, assigned case by case.

Source: engineerscanada.ca.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Heat & Mass Transfer in Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

Conduction, convection, radiation, heat exchangers and diffusion — the physics of drying, cooling, freezing and cold-store walls.

Our 37 Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus questions in this subject: 0 easy, 11 medium, 26 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus and are not shown on any other exam's page.

Question 1 · hard

A vertical plate 0.5 m high loses heat by free convection to air (k = 0.026 W/m·K). For the stated temperature difference, Gr = 1.4 × 10⁸ and Pr = 0.71. Using Nu = 0.59 Ra^(1/4) for 10⁴ < Ra < 10⁹ and Nu = 0.10 Ra^(1/3) for 10⁹ < Ra < 10¹³, the average heat-transfer coefficient is closest to

  1. 3.06 W/m²·K
  2. 2.41 W/m²·K
  3. 3.34 W/m²·K
  4. 58.9 W/m²·K
Answer and working

A. 3.06 W/m²·K

Ra = Gr × Pr = 9.94 × 10⁷, in the laminar range, so Nu = 0.59 × (9.94 × 10⁷)^0.25 = 58.9 and h = 58.9 × 0.026/0.5 = 3.06 W/m²·K. The turbulent correlation gives 2.41 but does not apply below 10⁹; using Gr instead of Ra gives 3.34; 58.9 is Nu, not h.

Question 2 · hard

A surface of emissivity 0.9 at 350 K exchanges radiation with large surroundings at 300 K. The linearised radiation heat-transfer coefficient h_r = εσ(T1 + T2)(T1² + T2²) is closest to

  1. 7.05 W/m²·K
  2. 7.83 W/m²·K
  3. 0.035 W/m²·K
  4. 352 W/m²·K
Answer and working

A. 7.05 W/m²·K

h_r = 0.9 × 5.67 × 10⁻⁸ × 650 × (350² + 300²) = 0.9 × 5.67 × 10⁻⁸ × 650 × 212,500 = 7.05 W/m²·K. Omitting ε gives 7.83; using °C gives a meaningless 0.035; 352 W/m²·K is the heat flux (h_r × 50 K), not the coefficient. h_r is of the same order as a natural-convection coefficient, so radiation is never negligible for surfaces in still air.

Question 3 · hard

A steel sphere 20 mm in diameter (ρ = 7,800 kg/m³, c = 460 J/kg·K, k = 40 W/m·K) at 300 °C is cooled in air at 30 °C with h = 50 W/m²·K. The time for it to reach 100 °C is closest to

  1. 263 s
  2. 969 s
  3. 177 s
  4. 323 s
Answer and working

D. 323 s

Check Bi = hL_c/k = 50 × (0.02/6)/40 = 0.0042 < 0.1, so lumped. τ = ρcL_c/h = 7800 × 460 × 0.00333/50 = 239.2 s. t = τ ln[(T_i − T∞)/(T − T∞)] = 239.2 × ln(270/70) = 323 s. Forgetting to subtract T∞ gives 263 s; using r instead of r/3 gives 969 s; a linear (non-exponential) decay gives 177 s.

Question 4 · hard

A dairy heat exchanger has a clean overall coefficient of 1,000 W/m²·K. A fouling resistance of 0.0002 m²·K/W is expected on each side. To deliver the same duty at the same LMTD, the area must be increased by about

  1. 20%
  2. 28.6%
  3. 40%
  4. 0.04%
Answer and working

C. 40%

Fouled: 1/U = 1/1000 + 2 × 0.0002 = 0.0014, so U = 714 W/m²·K. A ∝ 1/U, so A_fouled/A_clean = 1000/714 = 1.40: 40% more area. 20% counts fouling on one side only; 28.6% is the fall in U, not the rise in area. 0.04% reports the total fouling resistance (0.0004) as a percentage.

Question 5 · hard

In a counterflow exchanger the hot fluid (C = 2,000 W/K) enters at 150 °C and the cold fluid (C = 4,000 W/K) enters at 30 °C; UA = 3,000 W/K. Using ε = [1 − exp(−NTU(1 − C_r))]/[1 − C_r exp(−NTU(1 − C_r))], the heat-transfer rate is closest to

  1. 143 kW
  2. 186 kW
  3. 332 kW
  4. 166 kW
Answer and working

D. 166 kW

C_min = 2,000 W/K (hot), C_r = 0.5, NTU = 3,000/2,000 = 1.5. ε = [1 − e^(−0.75)]/[1 − 0.5e^(−0.75)] = 0.6908. Q = ε C_min ΔT_max = 0.6908 × 2,000 × 120 = 166 kW. The parallel-flow relation gives 143 kW; the C_r = 0 relation gives 186 kW; using C_max in Q_max gives 332 kW, which exceeds what the hot fluid can give up.

Question 6 · medium

In a condenser where N horizontal tubes are stacked in a vertical column, the average condensation coefficient per tube compared with a single tube is

  1. higher, because the falling condensate stirs the vapour
  2. exactly the same, because each tube in the column sees the same saturated vapour at the same pressure
  3. lower, because condensate from upper tubes thickens the film on lower tubes
  4. higher, because the lower tubes are cooler
Answer and working

C. lower, because condensate from upper tubes thickens the film on lower tubes

Nusselt's analysis gives an average coefficient that falls roughly as N^(−1/4) for a column of N tubes, since drainage from above thickens the film below. In practice splashing and ripples reduce the penalty somewhat, but the average is still below the single-tube value.

Question 7 · medium

Gases A and B undergo equimolar counter-diffusion through a 50 mm path at 300 K. The partial pressure of A is 10 kPa at one end and 2 kPa at the other; D_AB = 1.5 × 10⁻⁵ m²/s and R = 8.314 kJ/kmol·K. The molar flux of A is

  1. 9.62 × 10⁻⁴ kmol/m²·s
  2. 1.07 × 10⁻⁵ kmol/m²·s
  3. 9.62 × 10⁻⁷ kmol/m²·s
  4. 9.62 × 10⁻⁸ kmol/m²·s
Answer and working

C. 9.62 × 10⁻⁷ kmol/m²·s

N_A = D(p_A1 − p_A2)/(RTL) = 1.5 × 10⁻⁵ × 8/(8.314 × 300 × 0.05) = 9.62 × 10⁻⁷ kmol/m²·s. Pressures in kPa with R in kJ/kmol·K give kmol/m²·s. Entering the pressures in Pa while keeping R in kJ/kmol·K gives 9.62 × 10⁻⁴, 1,000 times too large; using 27 °C instead of 300 K gives 1.07 × 10⁻⁵; entering L as 0.5 m gives 9.62 × 10⁻⁸.

Question 8 · medium

A gas-phase diffusivity correlation gives D ∝ T^1.75 at constant pressure. If D = 2.5 × 10⁻⁵ m²/s at 300 K, its value at 350 K is closest to

  1. 2.92 × 10⁻⁵ m²/s
  2. 3.27 × 10⁻⁵ m²/s
  3. 1.91 × 10⁻⁵ m²/s
  4. 15.65 × 10⁻⁵ m²/s
Answer and working

B. 3.27 × 10⁻⁵ m²/s

D2 = D1(T2/T1)^1.75 = 2.5 × 10⁻⁵ × (350/300)^1.75 = 2.5 × 10⁻⁵ × 1.310 = 3.27 × 10⁻⁵ m²/s. A linear scaling gives 2.92; inverting the ratio gives 1.91; using °C gives 15.65.

Question 9 · hard

For a counterflow heat exchanger with NTU = 3, which change raises the effectiveness the most?

  1. Changing the arrangement to parallel flow at the same NTU and C_r
  2. Increasing NTU from 3 to 3.5 at C_r = 1
  3. Increasing C_r from 0.5 to 1 at fixed NTU
  4. Reducing the capacity ratio C_r from 1 to 0 at fixed NTU
Answer and working

D. Reducing the capacity ratio C_r from 1 to 0 at fixed NTU

At NTU = 3: counterflow with C_r = 1 gives ε = 3/4 = 0.750; with C_r = 0, ε = 1 − e⁻³ = 0.950, a gain of 0.200. Raising NTU to 3.5 at C_r = 1 gives 3.5/4.5 = 0.778, a gain of only 0.028. Parallel flow always lowers ε, and raising C_r lowers ε for a given NTU.

Question 10 · hard

In a deep, fixed bed of grain dried with heated air entering at the bottom, a drying front moves upward through the bed. The practical consequence that operators manage by stirring the grain or limiting bed depth is that

  1. the top layers dry first because warm air rises
  2. all layers dry at the same rate, so no gradient forms
  3. the bottom layers are overdried while the top layers stay wet, giving a large moisture gradient
  4. the exhaust air leaves the bed at the inlet air temperature throughout drying
Answer and working

C. the bottom layers are overdried while the top layers stay wet, giving a large moisture gradient

Air picks up moisture and cools as it rises, so drying occurs mainly in a zone near the inlet that moves upward. Grain below the front approaches equilibrium with hot inlet air and is overdried; grain above it is still wet. Exhaust air stays cool and humid until the front nears the top. Stirring, airflow reversal and shallow beds reduce the gradient.

A study plan for Heat & Mass Transfer in Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 37 questions): Condensation and boiling (5, 14%); Convective mass transfer (4, 11%); Diffusive mass transfer and Fick's law (4, 11%); Radiation: Stefan-Boltzmann law and view factors (4, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Transient conduction: lumped capacity and Heisler charts (4, 11%); Heat exchangers: effectiveness-NTU method (3, 8%); Simultaneous heat and mass transfer in drying (3, 8%); Composite walls and critical radius of insulation (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Convection and dimensionless numbers (Nu, Re, Pr) (2, 5%); Extended surfaces (fins) (2, 5%); Heat exchangers: LMTD method (2, 5%); Steady conduction through plane walls and cylinders (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Heat exchangers: effectiveness-NTU method (3 hard of 3), Simultaneous heat and mass transfer in drying (3 hard of 3), Composite walls and critical radius of insulation (2 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination sy

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.