LAISHA
Open Laisha

ICAR AICE-JRF/SRF Heat & Mass Transfer: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
71written to this exam in this subject
12syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Heat & Mass Transfer in ICAR AICE-JRF/SRF

PG-level depth: Heisler charts and product solutions, fin effectiveness, radiation networks and shields, ε–NTU relations and regeneration efficiency in pasteurisers, condensation and boiling regimes in evaporators, the heat–mass analogy and Lewis relation, Fick's second law and effective diffusivity, and thin-layer drying models.

Conduction, convection, radiation, heat exchangers and diffusion — the physics of drying, cooling, freezing and cold-store walls.

Our 71 ICAR AICE-JRF/SRF questions in this subject: 3 easy, 41 medium, 27 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

In laminar flow of a heavy oil (Pr = 1,000) along a heated flat plate, with heating starting at the leading edge, the thermal boundary-layer thickness is approximately

  1. ten times the velocity boundary-layer thickness
  2. one-tenth of the velocity boundary-layer thickness
  3. equal to the velocity boundary-layer thickness
  4. one-thousandth of the velocity boundary-layer thickness
Answer and working

B. one-tenth of the velocity boundary-layer thickness

For laminar flat-plate flow δ/δ_t ≈ Pr^(1/3). With Pr = 1,000, Pr^(1/3) = 10, so δ_t ≈ δ/10. High-Pr fluids diffuse momentum much faster than heat. Ten times thicker would apply to a very low-Pr fluid such as a liquid metal; one-thousandth wrongly uses Pr to the first power.

Question 2 · medium

A spherical thermocouple junction 1 mm in diameter (ρ = 8,500 kg/m³, c = 400 J/kg·K) is placed in a gas stream with h = 200 W/m²·K. Treating it as a lump, its time constant is closest to

  1. 2.83 s
  2. 8.5 s
  3. 17 s
  4. 0.047 s
Answer and working

A. 2.83 s

τ = ρVc/(hA_s) = ρc(D/6)/h, because V/A_s = D/6 for a sphere. τ = 8500 × 400 × (0.001/6)/200 = 2.83 s. Using V/A_s = r gives 8.5 s; using D gives 17 s; 0.047 s results from a spurious division by 60.

Question 3 · hard

In a counterflow exchanger the two fluids have equal heat-capacity rates. The hot fluid enters at 80 °C and the cold fluid enters at 20 °C and leaves at 60 °C. The mean temperature difference to use in Q = UAΔT_m is

  1. 20 °C
  2. 40 °C
  3. 0 °C, because ΔT1 − ΔT2 = 0
  4. undefined, so the exchanger cannot be designed with the LMTD method
Answer and working

A. 20 °C

Equal C means the hot fluid falls by the same 40 °C, leaving at 40 °C. ΔT1 = 80 − 60 = 20 °C and ΔT2 = 40 − 20 = 20 °C: the difference is constant along the exchanger, so ΔT_m = 20 °C. The LMTD formula gives 0/0 but its limit is 20 °C. 40 °C is the hot fluid's temperature drop, not the driving difference.

Question 4 · medium

An electrically heated element submerged in water is controlled by its power input. If the power is raised just above the critical heat flux, the element

  1. moves smoothly into transition boiling with a small rise in temperature
  2. returns to natural-convection boiling at a lower temperature
  3. jumps to the film-boiling branch at a much higher surface temperature, risking burnout
  4. stays at the same temperature because the latent heat of vaporisation absorbs all the extra power
Answer and working

C. jumps to the film-boiling branch at a much higher surface temperature, risking burnout

With heat flux imposed, the operating point cannot follow the falling transition branch; it jumps at the same flux to the film-boiling curve, where the surface temperature can be hundreds of degrees higher and may exceed the element's melting point. Transition boiling can be followed only when surface temperature is controlled, not heat flux.

Question 5 · medium

For laminar film condensation on a vertical plate, Nusselt's analysis gives h ∝ L^(−1/4). If the plate height is doubled with all else the same, the average coefficient becomes

  1. half the original
  2. twice the original
  3. 0.707 times the original
  4. 0.841 times the original
Answer and working

D. 0.841 times the original

h ∝ L^(−1/4), so h_new/h_old = 2^(−0.25) = 0.841. The thicker film on the lower part of a taller plate lowers the average coefficient, but only weakly; the total heat flow still rises, because the area doubles (1.68 times).

Question 6 · easy

The typical order of magnitude of binary diffusion coefficients at ordinary temperature is

  1. gases about 10⁻⁵ m²/s, liquids about 10⁻⁹ m²/s, solids much smaller
  2. gases about 10⁻⁹ m²/s, liquids about 10⁻⁵ m²/s
  3. about 10⁻⁵ m²/s for gases, liquids and solids alike
  4. gases about 10⁻² m²/s, liquids about 10⁻⁵ m²/s
Answer and working

A. gases about 10⁻⁵ m²/s, liquids about 10⁻⁹ m²/s, solids much smaller

Gas-phase diffusivities are around 10⁻⁵ m²/s (water vapour in air about 2.5 × 10⁻⁵), liquid-phase around 10⁻⁹ m²/s, and diffusion in solids and food matrices is slower still. This four-orders-of-magnitude gap is why internal diffusion controls drying in the falling-rate period.

Question 7 · medium

A solute diffuses steadily through a stagnant liquid layer 2 mm thick with D = 2 × 10⁻⁹ m²/s. Its concentrations on the two faces differ by 0.5 kmol/m³. The molar flux is

  1. 5.00 × 10⁻¹⁰ kmol/m²·s
  2. 5.00 × 10⁻⁷ kmol/m²·s
  3. 2.00 × 10⁻¹² kmol/m²·s
  4. 1.00 × 10⁻⁶ kmol/m²·s
Answer and working

B. 5.00 × 10⁻⁷ kmol/m²·s

N = DΔC/L = 2 × 10⁻⁹ × 0.5/0.002 = 5.0 × 10⁻⁷ kmol/m²·s, the mass analogue of Q = kAΔT/L. Entering L as 2 (mm) gives 5 × 10⁻¹⁰; multiplying by L gives 2 × 10⁻¹²; omitting ΔC gives 1 × 10⁻⁶ with the wrong units.

Question 8 · hard

Over a moist product in a dryer the convective heat-transfer coefficient is 30 W/m²·K. Air has ρ = 1.2 kg/m³ and c_p = 1,007 J/kg·K, and Le = 0.88. By the Chilton–Colburn analogy, h/h_m = ρ c_p Le^(2/3), the mass-transfer coefficient is closest to

  1. 24.8 × 10⁻³ m/s
  2. 27.0 m/s
  3. 25.9 × 10⁻³ m/s
  4. 27.0 × 10⁻³ m/s
Answer and working

D. 27.0 × 10⁻³ m/s

h_m = h/(ρ c_p Le^(2/3)) = 30/(1.2 × 1007 × 0.88^(2/3)) = 30/(1.2 × 1007 × 0.9183) = 0.02703 m/s. Taking Le^(2/3) = 1 (the Lewis relation) gives 24.8 × 10⁻³, a small error for air–water; using c_p in kJ/kg·K gives an impossible 27.0 m/s; using Le^(1/3) gives 25.9 × 10⁻³.

Question 9 · medium

Thin-layer drying of a grain sample follows the Lewis (Newton) model MR = exp(−kt) with k = 0.2 h⁻¹. The time to reach MR = 0.1 is closest to

  1. 4.5 h
  2. 5.0 h
  3. 0.5 h
  4. 11.5 h
Answer and working

D. 11.5 h

t = −ln(MR)/k = ln(10)/0.2 = 11.5 h. Using a linear decline gives 4.5 h; using log₁₀ instead of the natural logarithm gives 5.0 h; 0.5 h is MR/k.

Question 10 · medium

The Chilton–Colburn analogy states that j_H = St·Pr^(2/3) and j_D = St_m·Sc^(2/3) are both equal to

  1. the Lewis number
  2. C_f/2, half the skin-friction coefficient
  3. Nu/Sh
  4. the Reynolds number to the power 0.8
Answer and working

B. C_f/2, half the skin-friction coefficient

The j-factor analogy links heat, mass and momentum transfer: j_H = j_D = C_f/2 for flows without form drag, valid roughly for 0.6 < Pr < 60 and 0.6 < Sc < 3,000. It lets a measured friction factor or heat-transfer coefficient give the mass-transfer coefficient.

A study plan for Heat & Mass Transfer in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 71 questions): Diffusive mass transfer and Fick's law (10, 14%); Simultaneous heat and mass transfer in drying (9, 13%); Condensation and boiling (8, 11%); Convective mass transfer (7, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Extended surfaces (fins) (6, 8%); Heat exchangers: effectiveness-NTU method (6, 8%); Transient conduction: lumped capacity and Heisler charts (6, 8%); Convection and dimensionless numbers (Nu, Re, Pr) (5, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Heat exchangers: LMTD method (4, 6%); Radiation: Stefan-Boltzmann law and view factors (4, 6%); Steady conduction through plane walls and cylinders (4, 6%); Composite walls and critical radius of insulation (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Heat exchangers: LMTD method (3 hard of 4), Convection and dimensionless numbers (Nu, Re, Pr) (3 hard of 5), Heat exchangers: effectiveness-NTU method (3 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Diffusive mass transfer and Fick's law (2 easy of 10); Convective mass transfer (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.