LAISHA
Open Laisha

ICAR AICE-JRF/SRF Fluid Mechanics & Open Channel Hydraulics: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
67written to this exam in this subject
18syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Fluid Mechanics & Open Channel Hydraulics in ICAR AICE-JRF/SRF

PG-depth fluid mechanics and open-channel hydraulics: derivations and limits of Darcy-Weisbach and Hazen-Williams, Moody zones, Hardy Cross, specific energy and transitions, critical flow in non-rectangular sections, jump classification, gradually varied flow ideas and model laws.

Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.

Our 67 ICAR AICE-JRF/SRF questions in this subject: 5 easy, 38 medium, 24 hard, across 18 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A soap bubble 40 mm in diameter is made from a solution with surface tension 0.04 N/m. What is the excess of pressure inside the bubble over the outside?

  1. 16.0 Pa
  2. 2.00 Pa
  3. 4.00 Pa
  4. 8.00 Pa
Answer and working

D. 8.00 Pa

A soap bubble has two surfaces, so Δp = 8σ/d = 8 × 0.04/0.04 = 8.00 Pa. 4σ/d = 4.00 Pa is the result for a liquid droplet (one surface); 2σ/d is for a cylindrical jet; using the radius in 8σ/d gives 16.0 Pa.

Question 2 · hard

An inverted U-tube manometer with oil of relative density 0.8 in its upper bend is connected between two points on a water pipeline. The oil-water interfaces differ in level by 200 mm. What is the difference in piezometric head between the two points, in metres of water?

  1. 0.200 m
  2. 0.360 m
  3. 0.0400 m
  4. 0.160 m
Answer and working

C. 0.0400 m

For a lighter manometric liquid, h = x(1 − S_light/S) = 0.2 × (1 − 0.8) = 0.0400 m of water. Using x × S_light gives 0.160 m; the inverted manometer is chosen precisely because it gives a large deflection for a small head difference. 0.360 m uses (1 + 0.8) instead of (1 − 0.8).

Question 3 · medium

For which of these situations is the Hazen-Williams equation NOT appropriate?

  1. Turbulent flow of water at 20 °C in a 150 mm PVC main
  2. Laminar flow of oil in a hydraulic line
  3. Sizing a sprinkler sub-main carrying irrigation water
  4. Friction loss in a 300 mm ductile-iron water main
Answer and working

B. Laminar flow of oil in a hydraulic line

Hazen-Williams is empirical and fitted to turbulent flow of water at ordinary temperatures. It has no viscosity term, so it cannot handle other fluids or laminar flow; Darcy-Weisbach with f = 64/Re (laminar) or the Moody diagram must be used instead.

Question 4 · medium

A pipe contracts suddenly and the velocity in the smaller pipe is 3 m/s. If the coefficient of contraction at the vena contracta is 0.62, what is the head loss at the contraction?

  1. 0.229 m
  2. 0.172 m
  3. 0.0662 m
  4. 0.281 m
Answer and working

B. 0.172 m

h_c = (1/C_c − 1)² V₂²/2g = (1/0.62 − 1)² × 9/19.62 = 0.376 × 0.459 = 0.172 m. The rule of thumb 0.5V₂²/2g gives 0.229 m when C_c is not known; forgetting to square gives 0.281 m. 0.0662 m uses (1 − C_c)² instead of (1/C_c − 1)².

Question 5 · medium

What is the coefficient of discharge of an internal (Borda, re-entrant) mouthpiece running free, where the jet does not touch the mouthpiece walls?

  1. 0.855
  2. 0.50
  3. 0.707
  4. 0.62
Answer and working

B. 0.50

Momentum analysis of the Borda mouthpiece, where the wall pressure around the entrance is hydrostatic, gives C_c = 0.5; with C_v ≈ 1, C_d = 0.5. Running full, C_d is about 0.707. 0.855 is the external cylindrical mouthpiece. 0.62 is the usual sharp-edged orifice value.

Question 6 · hard

A rectangular sharp-crested weir 2 m long, with end contractions at both ends, runs under a head of 0.4 m. Using the Francis formula (SI), what is the discharge?

  1. 0.357 m³/s
  2. 0.894 m³/s
  3. 0.931 m³/s
  4. 0.912 m³/s
Answer and working

B. 0.894 m³/s

Q = 1.84(L − 0.1nH)H^1.5 with n = 2: effective length = 2 − 0.1 × 2 × 0.4 = 1.92 m, Q = 1.84 × 1.92 × 0.4^1.5 = 0.894 m³/s. Ignoring the contractions gives 0.931 m³/s; counting only one gives 0.912 m³/s. 0.357 m³/s uses H^2.5 instead of H^1.5.

Question 7 · medium

A hydraulic jump in a horizontal rectangular channel has depths of 0.5 m before and 2.0 m after the jump. What is the head loss in the jump?

  1. 1.50 m
  2. 0.844 m
  3. 0.562 m
  4. 3.38 m
Answer and working

B. 0.844 m

ΔE = (y₂ − y₁)³/(4y₁y₂) = 1.5³/(4 × 0.5 × 2.0) = 3.375/4 = 0.844 m. Omitting the 4 gives 3.38 m; squaring instead of cubing gives 0.562 m; 1.50 m is the jump height, not the loss.

Question 8 · easy

In the US Bureau of Reclamation classification, what type of jump forms when the upstream Froude number is about 6?

  1. Undular jump
  2. Weak jump
  3. Oscillating jump
  4. Steady jump
Answer and working

D. Steady jump

Fr₁ of about 4.5–9 gives a steady, well-balanced jump, preferred in stilling basins. 2.5–4.5 is oscillating (sends waves downstream, avoided); 1.7–2.5 weak; 1–1.7 undular; above 9 strong.

Question 9 · medium

In a hydraulic jump in a horizontal rectangular channel the sequent depth is six times the initial depth. What is the upstream Froude number?

  1. 6.00
  2. 4.58
  3. 2.45
  4. 3.46
Answer and working

B. 4.58

From y₂/y₁ = ½[√(1 + 8Fr₁²) − 1] = 6: √(1 + 8Fr₁²) = 13, so 8Fr₁² = 168, Fr₁² = 21 and Fr₁ = 4.58. The depth ratio itself (6) is not the Froude number. 2.45 is √6 and 3.46 is √(2 × 6), neither from the jump equation.

Question 10 · hard

Flow through a large pipe valve is studied on a 1:10 model using the same water at the same temperature. For dynamic similarity (Reynolds' law), what model velocity corresponds to a prototype velocity of 1.5 m/s?

  1. 15 m/s
  2. 4.74 m/s
  3. 0.15 m/s
  4. 0.474 m/s
Answer and working

A. 15 m/s

Reynolds similarity with the same fluid needs V_m D_m = V_p D_p, so V_m = V_p × (D_p/D_m) = 1.5 × 10 = 15 m/s. Using Froude scaling (V ∝ L^0.5) gives 0.474 m/s, which is wrong for a closed conduit where gravity plays no role in the dynamics. 4.74 m/s multiplies by √10 and 0.15 m/s divides by 10.

A study plan for Fluid Mechanics & Open Channel Hydraulics in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (51% of the 67 questions): Hydraulic jump (7, 10%); Dimensional analysis and similitude (6, 9%); Pipes in series and parallel (6, 9%); Specific energy and critical depth (6, 9%); Momentum equation (5, 7%); Darcy-Weisbach equation and Moody diagram (4, 6%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Most economical channel section (4, 6%); Orifices, mouthpieces and tank emptying (4, 6%); Forces on submerged surfaces and buoyancy (3, 4%); Laminar and turbulent flow in pipes (3, 4%); Properties of fluids (3, 4%); Uniform flow in open channels: Manning and Chezy (3, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Weirs and notches (3, 4%); Bernoulli's equation: venturimeter, orifice meter and pitot tube (2, 3%); Continuity equation (2, 3%); Hazen-Williams equation (2, 3%); Hydrostatics and manometry (2, 3%); Minor losses (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Forces on submerged surfaces and buoyancy (3 hard of 3), Pipes in series and parallel (3 hard of 6), Darcy-Weisbach equation and Moody diagram (2 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Properties of fluids (1 easy of 3); Darcy-Weisbach equation and Moody diagram (1 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Fluid Mechanics & Open Channel Hydraulics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.