LAISHA
Open Laisha

ICAR AICE-JRF/SRF Tractor Systems & Controls: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
55written to this exam in this subject
15syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Tractor Systems & Controls in ICAR AICE-JRF/SRF

Tractor design principles: selection of ratios and speed steps, clutch and brake design, power-shift and CVT concepts, load-sensing hydraulics, free-link vs restrained-link hitching and virtual hitch point, MFWD lead, tyre and ballast selection, ROPS.

Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.

Our 55 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 25 medium, 30 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

An oil-immersed disc brake has 8 friction faces, clamping force 8,000 N, μ = 0.12 and mean radius 90 mm. Its braking torque is

  1. 173 N·m
  2. 1,382 N·m
  3. 5,760 N·m
  4. 691 N·m
Answer and working

D. 691 N·m

T = μ F n R_m = 0.12 × 8,000 × 8 × 0.09 = 691 N·m. Using n = 2 gives 173; using the diameter gives double; leaving out μ gives an impossible value. In figures, double is 1,382 N·m and leaving out μ gives 8,000 × 8 × 0.09 = 5,760.

Question 2 · medium

The main advantage of a track-type tractor over a wheeled tractor of similar mass on soft soil is

  1. higher road speed, since the track links act like a continuous set of gears
  2. lower ground pressure and higher tractive efficiency from a long contact patch
  3. lower purchase price
  4. tighter turning without skidding, because the tracks pivot on a central kingpin
Answer and working

B. lower ground pressure and higher tractive efficiency from a long contact patch

Tracks spread the load over a long, flat contact patch, lowering contact pressure and slip on soft soil. Tracks are slower on the road, cost more, and turn by skid steering, which disturbs soil.

Question 3 · medium

Planetary final drives are placed at the wheel hubs on most medium and large tractors because

  1. they allow the PTO to be driven directly from the wheel hub without a separate shaft
  2. they need no lubrication
  3. they give a speed increase at the wheel, which suits high-speed road transport
  4. they are compact, share load among planets and shorten the highest-torque section
Answer and working

D. they are compact, share load among planets and shorten the highest-torque section

Putting a compact, load-sharing reduction at the hub means only a short path carries the very high final torque, reducing shaft and bearing size elsewhere.

Question 4 · hard

A tractor pulls to the right under road braking with the pedals latched. The most probable cause is

  1. too much toe-in on the front wheels pulling the tractor to the right
  2. low PTO speed
  3. unequal brake adjustment or oil-contaminated linings on the left
  4. an engaged differential lock that drags the right-hand wheel
Answer and working

C. unequal brake adjustment or oil-contaminated linings on the left

If the right brake grips harder than the left, the tractor swings right. Unequal free travel or loss of friction on the left side (oil from a leaking seal) is the usual cause.

Question 5 · medium

In a hydrostatic power steering system, if the engine stops while moving

  1. steering usually locks solid
  2. steering becomes lighter
  3. it can still be steered, with more effort, because the metering unit acts as a hand pump
  4. the wheels return to the straight-ahead position automatically under the caster action of the kingpins
Answer and working

C. it can still be steered, with more effort, because the metering unit acts as a hand pump

The orbital metering unit contains a gerotor set that pumps oil to the cylinder when turned by hand, giving emergency steering without engine power.

Question 6 · hard

Automatic guidance systems for tractors are most easily fitted to hydrostatic steering because

  1. an electrohydraulic valve can drive the steering cylinder directly, with no mechanical link to move
  2. hydrostatic steering has no cylinder, so a guidance motor can turn the steering column directly
  3. it uses Ackermann geometry exactly, so the guidance computer needs no correction for the wheel angle at all
  4. it needs no hydraulic pump, so the guidance system can run from the tractor battery alone
Answer and working

A. an electrohydraulic valve can drive the steering cylinder directly, with no mechanical link to move

With no mechanical column to actuate, the guidance controller simply meters oil to the cylinder through its own valve.

Question 7 · hard

Compared with an open-centre system, the main disadvantages of a closed-centre load-sensing system are

  1. higher cost and greater sensitivity to oil contamination
  2. higher standby energy loss
  3. inability to run two functions together
  4. lower maximum pressure
Answer and working

A. higher cost and greater sensitivity to oil contamination

CCLS saves energy and allows several functions at once, but the variable pump and valves are costlier and have fine clearances that contamination damages.

Question 8 · medium

Under ISO 730, a Category 2 three-point hitch uses lower-link pins of nominal diameter

  1. 22 mm
  2. 28.7 mm
  3. 19 mm
  4. 37.4 mm
Answer and working

B. 28.7 mm

Category 1 uses 22 mm lower-link and 19 mm top-link pins; Category 2 uses 28.7 mm lower-link and 25.5 mm top-link pins; larger categories use larger pins. 37.4 mm is the Category 3 lower-link pin.

Question 9 · hard

Adding ballast to a tractor improves drawbar pull only up to a point because

  1. extra mass also adds rolling resistance and compaction, so gains stop beyond an optimum
  2. ballast reduces engine power
  3. ballast lowers PTO speed
  4. tyres cannot carry any extra mass beyond the weight of the tractor itself without bursting
Answer and working

A. extra mass also adds rolling resistance and compaction, so gains stop beyond an optimum

More load on the drive wheels increases gross traction, but rolling resistance and soil compaction also rise; the best ballast balances slip against rolling resistance for the job.

Question 10 · medium

The international standard that sets the location, direction of movement and actuating forces of tractor operator controls is

  1. ISO 500
  2. ISO 15077
  3. ISO 730
  4. ISO 5353
Answer and working

B. ISO 15077

ISO 500 covers PTOs, ISO 730 the three-point hitch and ISO 5353 the seat index point. ISO 15077 covers operator controls.

A study plan for Tractor Systems & Controls in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 55 questions): CVT and power-shift transmissions (6, 11%); Tyres and ballasting (6, 11%); Hydraulic system: open and closed centre (5, 9%); Brakes (4, 7%); Gearbox and transmission: sliding, constant and synchromesh (4, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Operator controls and ROPS (4, 7%); Power take-off: standards and speeds (4, 7%); Three-point hitch: categories, free and restrained links (4, 7%); Draft and position control (3, 5%); Final drive (3, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Power tillers (3, 5%); Steering geometry (Ackermann) and power steering (3, 5%); Clutch: single and dual plate (2, 4%); Differential and differential lock (2, 4%); Tractor types and selection (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Clutch: single and dual plate (2 hard of 2), Gearbox and transmission: sliding, constant and synchromesh (3 hard of 4), Tyres and ballasting (4 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Tractor Systems & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.