LAISHA
Open Laisha

Rajasthan PSC Tractor Systems & Controls: practice questions

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
28written to this exam in this subject
13syllabus units

About Rajasthan PSC

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.

Source: rpsc.rajasthan.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Tractor Systems & Controls in Rajasthan PSC

Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.

Our 28 Rajasthan PSC questions in this subject: 14 easy, 14 medium, 0 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Rajasthan PSC and are not shown on any other exam's page.

Question 1 · medium

A tractor's PTO reaches 540 rev/min at 1900 engine rev/min. If the operator runs the engine at 2100 rev/min, the PTO turns at about

  1. 597 rev/min
  2. 540 rev/min
  3. 489 rev/min
  4. 740 rev/min
Answer and working

A. 597 rev/min

PTO ratio = 1900/540 = 3.52:1. At 2100 rev/min the PTO turns 2100/3.52 = 597 rev/min, over-speeding the implement by 10.5%. The PTO speed is fixed to engine speed by gearing, so it is not held at 540; 489 inverts the proportion. 740 adds the 200 rev/min engine increase directly to the PTO speed.

Question 2 · medium

A single-acting lift cylinder has a 90 mm bore and 120 mm stroke. The pump supplies 25 L/min to it. The time for a full lift is

  1. 1.83 s
  2. 0.46 s
  3. 7.33 s
  4. 0.03 s
Answer and working

A. 1.83 s

Swept volume = π/4 × 0.09² × 0.12 = 0.000763 m³ = 0.763 L. Time = 0.763/25 min = 0.0305 min = 1.83 s. Using the radius in πd²/4 gives a quarter; 0.03 is the answer in minutes read as seconds. In figures, a quarter is 0.46 s; 7.33 s uses πd² without the /4.

Question 3 · easy

Each rear tyre of a tractor has an internal volume of 400 L. Both are filled to the usual 75% with a ballast solution of density 1.2 kg/L. The added mass is

  1. 360 kg
  2. 960 kg
  3. 720 kg
  4. 600 kg
Answer and working

C. 720 kg

Mass = 2 tyres × 400 L × 0.75 × 1.2 kg/L = 720 kg. 360 kg is one tyre; 960 kg assumes a full tyre, which leaves no air cushion; 600 kg assumes plain water.

Question 4 · medium

The torsional damper springs in a clutch driven plate

  1. provide the clamping force that presses the driven plate onto the flywheel
  2. return the pedal
  3. cool the linings by circulating air across the friction faces
  4. absorb torsional vibration and shock between engine and transmission
Answer and working

D. absorb torsional vibration and shock between engine and transmission

Coil springs in the hub let the plate twist slightly relative to its hub, damping engine firing pulses and shocks. Clamping force comes from the pressure-plate springs.

Question 5 · easy

Gear clash when shifting a sliding-mesh gearbox on a moving tractor happens because

  1. the oil level is too high
  2. the synchroniser is working
  3. the PTO is engaged
  4. the gears to be meshed are turning at different speeds
Answer and working

D. the gears to be meshed are turning at different speeds

Teeth can mesh cleanly only when their pitch-line speeds match. Sliding-mesh boxes have no synchroniser, so they need the tractor stopped or double-declutching.

Question 6 · medium

Lengthening or shortening the top link of a mounted plough mainly adjusts

  1. the side-to-side level
  2. fore-and-aft pitch
  3. the hitch lift capacity
  4. the PTO output speed
Answer and working

B. fore-and-aft pitch

The top link sets the implement's pitch (e.g. levelling a plough front to rear). Side-to-side level is set by the lift rods.

Question 7 · medium

When filling a tractor tyre with liquid ballast, the valve is placed at the top and the tyre filled to about

  1. 75% of its volume
  2. 100% of its volume
  3. 25% of its volume only
  4. 50% by mass of the tractor
Answer and working

A. 75% of its volume

With the valve at the top the liquid reaches about three-quarters full, leaving air to cushion the load and allow pressure adjustment.

Question 8 · easy

Steel cage wheels are fitted to a power tiller for

  1. road transport at speed
  2. dry-land ploughing on hard soil
  3. wet paddy fields
  4. reducing engine speed
Answer and working

C. wet paddy fields

Cage wheels sink into the mud and give traction where rubber tyres slip; they are removed for road work. They are used for puddling and other wet-field work.

Question 9 · medium

A foldable two-post ROPS has been lowered to pass under a low shed door. The correct practice is to

  1. leave it folded for the rest of the day
  2. remove the seat belt
  3. drill it to fit a sunshade
  4. raise and lock it as soon as the low clearance is passed
Answer and working

D. raise and lock it as soon as the low clearance is passed

A folded ROPS gives no protection. Drilling or welding a ROPS can destroy its certified strength.

Question 10 · easy

The most common way a tractor overturns backwards is when

  1. the front tyres are over-inflated, so the front end usually bounces up and the tractor tips back on field bumps
  2. the PTO speed is too low
  3. the rear wheels are held and axle torque rotates the tractor about them, or a load is hitched high
  4. the differential lock is released
Answer and working

C. the rear wheels are held and axle torque rotates the tractor about them, or a load is hitched high

When the wheels cannot turn, drive torque lifts the front; with a high hitch the pull adds to this moment. Rearward overturns happen in a second or two.

A study plan for Tractor Systems & Controls in Rajasthan PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 28 questions): Power take-off: standards and speeds (4, 14%); Brakes (3, 11%); Clutch: single and dual plate (3, 11%); Differential and differential lock (2, 7%); Gearbox and transmission: sliding, constant and synchromesh (2, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Hydraulic system: open and closed centre (2, 7%); Operator controls and ROPS (2, 7%); Power tillers (2, 7%); Three-point hitch: categories, free and restrained links (2, 7%); Tractor types and selection (2, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Tyres and ballasting (2, 7%); Draft and position control (1, 4%); Steering geometry (Ackermann) and power steering (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Differential and differential lock (2 easy of 2); Gearbox and transmission: sliding, constant and synchromesh (2 easy of 2).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Rajasthan PSC Tractor Systems & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.