LAISHA
Open Laisha

Farm Machinery Training & Testing Institutes Tractor Systems & Controls: practice questions

Farm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) · India · Ministry of Agriculture & Farmers Welfare, Government of India

Original practice questions written to the published syllabus · not past papers
10worked here, free
23written to this exam in this subject
13syllabus units

About Farm Machinery Training & Testing Institutes

Farm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) is a professional certification run by Ministry of Agriculture & Farmers Welfare, Government of India, for candidates in India. Not an exam: short training courses and machinery testing (commercial, batch, confidential, CMVR).

Official site: nerfmtti.nic.in.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Tractor Systems & Controls in Farm Machinery Training & Testing Institutes

Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.

Our 23 Farm Machinery Training & Testing Institutes questions in this subject: 9 easy, 13 medium, 1 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Farm Machinery Training & Testing Institutes and are not shown on any other exam's page.

Question 1 · medium

A tractor has a track width of 1.6 m and its centre of gravity is 0.9 m above the ground, midway between the wheels. Neglecting tyre deflection and axle pivoting, the static side slope at which it would tip is

  1. 60.6°
  2. 48.4°
  3. 41.6°
  4. 62.7°
Answer and working

C. 41.6°

Tipping starts when the weight line passes outside the downhill wheel: tan θ = (t/2)/h = 0.8/0.9 = 0.889, θ = 41.6°. Using the full track gives 60.6°; inverting gives 48.4°. Real tractors tip well below this because the front axle pivots, tyres deflect, and dynamics and bumps add to the static case, so this figure is an upper bound, never a safe working limit. 62.7° uses sin⁻¹ instead of tan⁻¹ (sin θ = 0.8/0.9).

Question 2 · medium

A tractor is working with the differential lock engaged. The crown wheel turns at 30 rev/min (after the final drive the wheels would turn at 6 rev/min each). If the operator now tries a turn on firm ground without releasing the lock, the wheel speeds are

  1. both 6 rev/min, so one tyre must slip or scrub and the axle is heavily strained
  2. outer 7 rev/min and inner 5 rev/min, as in a normal turn, because the lock acts only in a straight line
  3. outer 12 rev/min and inner zero
  4. the lock releases the outer wheel automatically on every tractor as soon as the steering is turned
Answer and working

A. both 6 rev/min, so one tyre must slip or scrub and the axle is heavily strained

With the lock engaged both side gears are tied to the case, so both wheels turn at crown speed/final drive = 30/5 = 6 rev/min. On a turn the outer wheel needs to go faster, so something must slip, which strains shafts and gears and makes the tractor resist turning. Some electronic locks disengage with steering angle, but this is not true of every tractor; the rule is to release the lock before turning.

Question 3 · easy

A tractor clutch slips under load but disengages fully. The first adjustment to check is

  1. engine idle speed setting
  2. brake pedal latch adjustment
  3. clutch pedal free play
  4. rear tyre inflation pressure
Answer and working

C. clutch pedal free play

With no free play the release bearing keeps pressure on the release levers, reducing spring force on the plate, so it slips. Too much free play causes dragging instead. Free play is lost gradually as the linings wear.

Question 4 · easy

The differential lock should be

  1. kept engaged permanently for better traction, since it causes no wear on firm ground
  2. engaged only for straight travel in slippery conditions and released before turning
  3. engaged on the road for stability
  4. engaged during sharp headland turns to stop the inner wheel from spinning
Answer and working

B. engaged only for straight travel in slippery conditions and released before turning

A locked axle resists turning, strains the drive train and can cause loss of steering and overturning. Use it only in a straight line and release it before turning.

Question 5 · easy

Before an operator dismounts to unblock a PTO-driven implement, the correct action is to

  1. reduce engine speed to idle and set the handbrake before clearing the blockage
  2. disengage only the travel clutch and keep the engine idling for a quick restart
  3. raise the hitch and leave the PTO running so the blockage can clear itself
  4. disengage the PTO, stop the engine, remove the key and wait for parts to stop
Answer and working

D. disengage the PTO, stop the engine, remove the key and wait for parts to stop

A rotating PTO shaft winds in clothing in a fraction of a second. Only a stopped engine and stationary shaft are safe.

Question 6 · easy

Before driving a tractor on a public road, the two brake pedals should be

  1. left independent for quick turns
  2. latched together so both rear wheels brake equally
  3. disconnected
  4. set with maximum free play
Answer and working

B. latched together so both rear wheels brake equally

Braking one wheel at road speed swings the tractor sharply and can overturn it. Latching the pedals prevents that.

Question 7 · medium

Stabilisers or check chains on the lower links should be

  1. tight for a rotary tiller or sprayer and allowed some sideways float for a plough
  2. always fully slack so the implement can swing freely behind the tractor
  3. always fully tight
  4. removed when the PTO is used, since they foul the PTO drive shaft on every implement
Answer and working

A. tight for a rotary tiller or sprayer and allowed some sideways float for a plough

Tools that must follow the tractor exactly need tight stabilisers; a plough must be free to find its own line of draft, so some sideways movement is allowed.

Question 8 · medium

Hitching a heavy load to the tractor's top-link bracket or axle housing instead of the drawbar is dangerous because

  1. it overloads the PTO shaft, which runs directly beneath the top-link bracket
  2. it can overheat the hydraulics by pressurising the lift cylinder
  3. the pull acts high above the rear axle and can rotate the tractor backwards
  4. it wears the front tyres
Answer and working

C. the pull acts high above the rear axle and can rotate the tractor backwards

A high hitch point increases the overturning moment about the rear axle; with the wheels resisting, the tractor can rear over backwards in a second.

Question 9 · medium

A tractor with a heavy rear-mounted implement lifts its front wheels when turning on the headland. The correct remedy is

  1. add rear wheel weights so the rear tyres grip better during the turn
  2. reduce rear tyre pressure so the tractor squats back and holds the front wheels down
  3. add front-end weights so the front axle keeps its required share of the load
  4. engage the differential lock
Answer and working

C. add front-end weights so the front axle keeps its required share of the load

A heavy rear load shifts weight off the front axle and removes steering control. Front ballast restores it; rear ballast makes it worse.

Question 10 · medium

A ROPS on a second-hand tractor has been bent in a previous overturn and straightened by welding. The engineer should advise that

  1. it must be replaced or re-certified, as its energy-absorbing capacity may be lost
  2. it is safe if it looks straight and the welds have been ground smooth and painted
  3. it can be used if the seat belt is removed so the operator can jump clear
  4. it only needs repainting to stop rust starting at the welds, since steel regains strength
Answer and working

A. it must be replaced or re-certified, as its energy-absorbing capacity may be lost

ROPS are certified by testing to OECD or equivalent codes. Deformation and welding change the steel's behaviour, so a damaged ROPS cannot be assumed to protect.

A study plan for Tractor Systems & Controls in Farm Machinery Training & Testing Institutes

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 23 questions): Operator controls and ROPS (3, 13%); Brakes (2, 9%); Clutch: single and dual plate (2, 9%); Differential and differential lock (2, 9%); Hydraulic system: open and closed centre (2, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Power take-off: standards and speeds (2, 9%); Power tillers (2, 9%); Three-point hitch: categories, free and restrained links (2, 9%); Tyres and ballasting (2, 9%); CVT and power-shift transmissions (1, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Draft and position control (1, 4%); Gearbox and transmission: sliding, constant and synchromesh (1, 4%); Tractor types and selection (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Brakes (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: CVT and power-shift transmissions (1 easy of 1); Gearbox and transmission: sliding, constant and synchromesh (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Farm Machinery Training & Testing Institutes Tractor Systems & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.