Farm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) · India · Ministry of Agriculture & Farmers Welfare, Government of India
Original practice questions written to the published syllabus · not past papersFarm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) is a professional certification run by Ministry of Agriculture & Farmers Welfare, Government of India, for candidates in India. Not an exam: short training courses and machinery testing (commercial, batch, confidential, CMVR).
Official site: nerfmtti.nic.in.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Oil hydraulics on tractors and machines: pumps, motors, cylinders, valves and circuits.
Our 41 Farm Machinery Training & Testing Institutes questions in this subject: 17 easy, 20 medium, 4 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Farm Machinery Training & Testing Institutes and are not shown on any other exam's page.
On a mobile machine, why is a fine filter normally placed in the return line rather than in the pump suction line?
C. A fine element in the suction line could restrict inlet flow and cause pump cavitation
The pump inlet must stay above its minimum absolute pressure; a fine element, especially with cold oil or as it loads with dirt, would starve the pump, so suction lines carry only coarse strainers. Return oil is the dirtiest because it carries wear debris; ISO 4406 is a cleanliness code, not an installation rule; and filter media work at any normal temperature.
A mechanic receives a pinhole-leak jet of hydraulic oil into a finger. The wound looks like a tiny puncture and hurts little. The correct action is to
D. treat it as a surgical emergency and get immediate specialist medical care
High-pressure injection drives oil deep into tissue along tendon sheaths; the small entry wound hides serious damage, and delay risks loss of the finger. It needs urgent surgical assessment. Home wound care, squeezing or cooling do not remove injected oil. Leaks should be searched for with card or wood, never the hand.
A tractor pump flow test gives 58 L/min at 10 bar and 46 L/min at rated pressure, with the oil at normal working temperature. The rated flow at that speed is 60 L/min. The most reasonable interpretation is that
A. high internal leakage at pressure, showing a worn pump with ηv near 0.77
A positive-displacement pump's flow should fall only slightly with pressure. Here flow drops from 58 to 46 L/min, so ηv at rated pressure is 46/60 ≈ 0.77: internal leakage that rises with pressure is the signature of wear. A good low-pressure figure alone does not prove health. A low relief setting would cap pressure, not cut flow below it, and a suction blockage starves the pump at all pressures and causes cavitation noise.
After fitting a replacement piston motor to a harvester's header drive, a mechanic plugs its case-drain port because no drain hose came with it. The likely result is
A. case pressure builds with leakage oil until the shaft seal blows out
Internal leakage collects in the motor case; if it cannot drain freely to tank, case pressure builds until the shaft seal, which is rated for low pressure, fails. Plugging the drain does not make leakage disappear or raise speed, and it does not change the direction of rotation.
Two identical cylinders lift the two ends of a beam and are connected in parallel to one control valve. The beam load is heavier on the left. When the valve is opened,
D. the right cylinder, carrying the lighter load, extends first and the beam tilts
Pressure rises only as far as the lightest load needs, so the lighter-loaded cylinder moves first and takes the flow; the other moves only when the first stops. Synchronising parallel cylinders needs a flow divider, mechanical tie or a series arrangement.
Before a mechanic disconnects a line on a loader circuit fitted with a gas-charged accumulator for ride control, the accumulator must be discharged because
C. it stores oil under pressure that is released even with the engine stopped
A charged accumulator keeps oil at pressure after the pump stops, so opening a line can release a jet of oil or move the loader. The discharge procedure in the manual bleeds it to tank. The precharge gas is separated from the oil by a bladder, piston or diaphragm, and an accumulator is neither a filter nor a heater.
On a combine whose hydraulic oil keeps running hot, an infrared thermometer shows one valve section much hotter than everything else. The most likely meaning is
C. oil is passing through that section from high to low pressure without doing work
Heat appears where pressure is dropped without useful work: a relief valve passing oil, a leaking spool or a worn seal. A local hot spot points to that component. A large valve with low velocity runs cool, cleanliness does not concentrate heat, and an efficient cooler would not make one section hotter.
When ploughing with a mounted plough under draft control, the plough meets a patch of harder soil and its draft rises. The hydraulic system responds by
C. raising the plough slightly to bring the draft back toward the set value
Draft control holds the draft nearly constant: a rise in draft is sensed and the implement is raised slightly; when the draft falls it is lowered. Holding a fixed height is position control and floating on a wheel is float mode.
A farmer complains that under draft control the ploughing depth varies noticeably across a field with patches of light and heavy soil. The setting that limits this variation while keeping some load control is
B. mixed or intermix control, which blends the draft and position signals
Intermix control combines both signals so depth changes are limited while the draft still influences the hitch. Float gives no hitch control; drop rate only affects lowering speed; pure position control holds depth but gives up draft sensing and its weight transfer.
A tipping trailer uses a multi-stage telescopic cylinder. The main reason for this choice is that it
D. gives a long stroke from a short closed length under the body
Nested stages give a stroke much longer than the closed length, which a tipping body needs. Equal force both ways is a double-rod cylinder; telescopic cylinders have seals on every stage; and every circuit still needs relief protection.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.