NCEES PE Agricultural and Biological Engineering · USA · NCEES (ASABE is the content partner)
Original practice questions written to the published syllabus · not past papersNCEES PE Agricultural and Biological Engineering is a licensing and registration exam run by NCEES (ASABE is the content partner), for candidates in USA. Computer-based, 85 questions, 9.5-hour appointment (8.5 hours of exam). Once a year (next: 28 Oct 2026). Closed book with the electronic NCEES handbook and supplied searchable ASABE standards; SI and US customary units.
Source: ncees.org.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Explicit fluid-power content: pump and motor sizing from displacement, speed and efficiencies; cylinder force, speed and cycle time; hydraulic power and engine power required; pressure drop in lines and heat load; selecting valves and reading circuits drawn with standard symbols. Calculations dominate; unit consistency in psi, gpm, in³ and hp is tested.
Oil hydraulics on tractors and machines: pumps, motors, cylinders, valves and circuits.
Our 81 NCEES PE Agricultural and Biological Engineering questions in this subject: 16 easy, 44 medium, 21 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to NCEES PE Agricultural and Biological Engineering and are not shown on any other exam's page.
A hydraulic circuit delivers 60 L/min at a pressure of 180 bar. The hydraulic power is
D. 18 kW
P = p × Q = 180 × 10⁵ Pa × (60/60000) m³/s = 18000 W = 18 kW, which is the shortcut p(bar) × Q(L/min)/600 = 180 × 60/600. Treating 180 bar as 180 MPa with the /60 shortcut gives 180 kW; leaving minutes unconverted gives 1080 kW; a factor-of-ten slip gives 1.8 kW.
A pump delivers 20 US gal/min at 2500 psi. The hydraulic horsepower is closest to
D. 29.2 hp
Hydraulic horsepower = psi × gpm / 1714 = 2500 × 20 / 1714 = 29.2 hp. The value 21.8 is the same power in kilowatts written as horsepower; dividing by 1000 instead of 1714 gives 50.0; 2.9 is a decimal slip.
The ISO viscosity grade (ISO VG) of an industrial hydraulic oil, such as VG 46, refers to
A. its mid-point kinematic viscosity in mm²/s at 40 °C
ISO VG numbers are the mid-point kinematic viscosity in cSt (mm²/s) at 40 °C, within ±10 %. They are not dynamic viscosities, not temperatures and not viscosity indices; the viscosity index is a separate property describing how strongly viscosity changes with temperature.
A gear pump has a displacement of 40 cm³/rev, runs at 1800 rev/min and has a volumetric efficiency of 92 %. Its actual delivery is
B. 66.2 L/min
Q = V × n × ηv = 40 cm³ × 1800 /min × 0.92 = 66240 cm³/min = 66.2 L/min. 72.0 L/min is the theoretical flow; dividing by ηv (78.3) treats the pump as a motor; 6.62 is a units slip.
A double-acting cylinder has a 100 mm bore and a 50 mm rod. With 150 bar applied to the rod end, the retraction force is
B. 88.4 kN
Annulus area = π(0.1² − 0.05²)/4 = 5.890 × 10⁻³ m²; F = 150 × 10⁵ × 5.890 × 10⁻³ = 88.4 kN. The full piston area gives 117.8 kN (extension); the rod area gives 29.5 kN; 8.84 kN is a bar-to-pascal slip.
A pump supplies 50 L/min to the rod end of a cylinder with a 100 mm bore and a 70 mm rod to retract it. The flow returning from the cap end to tank during retraction is
A. 98.0 L/min
Return flow = Q × Ap/Aa = 50 × (π0.1²/4)/(π(0.1² − 0.07²)/4) = 50 × 0.01/0.0051 = 98.0 L/min. The return line, valve and filter must handle this, almost double the pump flow. Assuming it equals pump flow gives 50.0; inverting the ratio gives 25.5; using the rod area gives 102.0.
On an ISO 1219 directional valve symbol, what does each separate square in the row represent?
B. One switching position of the valve, with its flow paths drawn inside
Each square (envelope) is one position; arrows inside show where oil flows and T-shaped marks show blocked ports in that position. Ports are drawn as lines on the outside of one square; squares do not represent lands or flow rates.
Oil of 46 cSt flows at 60 L/min in a 20 mm bore line. The Reynolds number, and hence the flow regime, is
C. about 1384, laminar
v = (60/60000)/(π × 0.02²/4) = 3.18 m/s; Re = vD/ν = 3.18 × 0.020/46 × 10⁻⁶ = 1384, below about 2000, so laminar. Using 46 × 10⁻⁹ for cSt gives 1383956; using the radius instead of the diameter as the length in Re gives 692; 5536 comes from using the radius in the velocity area but the diameter in Re.
Why does a hydraulic line carry a much higher pressure loss on a cold morning than at normal working temperature, for the same flow?
B. Flow is laminar, so friction loss rises with viscosity, which is far higher when cold
With f = 64/Re in laminar flow, Δp = 32μLv/D², proportional to dynamic viscosity, which can rise many times at low temperature. Density changes little with temperature; cold, thick oil makes flow more laminar, not turbulent; and hose bores do not shrink appreciably.
An engineer compares two ways of slowing a fixed-pump-driven hydraulic motor to half speed: (i) a meter-in flow control, and (ii) halving the engine speed. Assuming the same load torque, which statement is correct?
B. Halving pump speed avoids the relief and throttling losses of the meter-in control
With meter-in on a fixed pump, half the flow crosses the relief at full pressure and the rest is throttled down to load pressure, so a large fraction of pump power becomes heat. Reducing pump speed halves the flow with pressure set by the load, so little is throttled. Pressure is set by the load torque in both cases, not by pump speed.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.