LAISHA
Open Laisha

NCEES PE Agricultural and Biological Engineering Food Quality, Safety & Process Plant Design: practice questions

NCEES PE Agricultural and Biological Engineering · USA · NCEES (ASABE is the content partner)

Original practice questions written to the published syllabus · not past papers
10worked here, free
59written to this exam in this subject
11syllabus units

About NCEES PE Agricultural and Biological Engineering

NCEES PE Agricultural and Biological Engineering is a licensing and registration exam run by NCEES (ASABE is the content partner), for candidates in USA. Computer-based, 85 questions, 9.5-hour appointment (8.5 hours of exam). Once a year (next: 28 Oct 2026). Closed book with the electronic NCEES handbook and supplied searchable ASABE standards; SI and US customary units.

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Food Quality, Safety & Process Plant Design in NCEES PE Agricultural and Biological Engineering

Measuring and assuring food quality, the food-safety systems regulators expect, and laying out a processing plant.

Our 59 NCEES PE Agricultural and Biological Engineering questions in this subject: 4 easy, 32 medium, 23 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES PE Agricultural and Biological Engineering and are not shown on any other exam's page.

Question 1 · medium

In texture profile analysis a biscuit gives hardness 40 N, cohesiveness 0.5 and springiness 0.8. Its chewiness is

  1. 20 N
  2. 64 N
  3. 32 N
  4. 16 N
Answer and working

D. 16 N

Gumminess = hardness × cohesiveness = 40 × 0.5 = 20 N; chewiness = gumminess × springiness = 20 × 0.8 = 16 N. 20 N is gumminess only; 32 N multiplies hardness by springiness alone. 64 N divides by cohesiveness instead of multiplying (40 × 0.8/0.5).

Question 2 · medium

Twenty subgroups of five packs from a filler give a grand mean of 250.4 g and an average range of 3.2 g. With A2 = 0.577 for n = 5, the upper control limit of the X̄ chart is

  1. 260.0 g
  2. 257.2 g
  3. 252.7 g
  4. 252.2 g
Answer and working

D. 252.2 g

UCL = X̿ + A2·R̄ = 250.4 + 0.577 × 3.2 = 252.2 g. Using D4 = 2.114 in place of A2 gives 257.2 g; using A2 for n = 4 (0.729) gives 252.7 g. 260.0 g uses 3R̄ in place of A2·R̄ (250.4 + 9.6).

Question 3 · medium

The difference between validation and verification in HACCP is that

  1. Validation applies only to prerequisite programmes; verification applies only to critical control points
  2. Validation is done by inspectors after an outbreak; verification is done by operators at each shift change of the line
  3. Validation shows a control measure is able to control the hazard; verification checks the plan is followed and working
  4. Validation is the daily record review; verification is the scientific study that sets critical limits
Answer and working

C. Validation shows a control measure is able to control the hazard; verification checks the plan is followed and working

Validation obtains evidence that the measures are capable of controlling the hazard; verification confirms ongoing compliance and effectiveness, through calibration, record review and sampling. The two are often swapped by students.

Question 4 · hard

How does the FSMA preventive controls approach differ from classic HACCP in how controls are managed?

  1. Controls apply only to finished product testing, not to process steps
  2. Not every control needs a critical limit; management is scaled to the control's role
  3. Controls are optional where a facility holds a private certification
  4. Every control must be treated as a CCP with a critical limit monitored on every lot produced
Answer and working

B. Not every control needs a critical limit; management is scaled to the control's role

Under HARPC, process controls include CCPs but allergen, sanitation and supply-chain controls are managed with monitoring, corrections and verification appropriate to their role, without necessarily having critical limits. Certification does not replace legal duties.

Question 5 · easy

In the United States, which agency regulates meat, poultry and processed egg products?

  1. Centers for Disease Control and Prevention
  2. Environmental Protection Agency
  3. USDA Food Safety and Inspection Service
  4. Food and Drug Administration
Answer and working

C. USDA Food Safety and Inspection Service

USDA-FSIS regulates meat, poultry and processed egg products; FDA regulates most other foods; EPA sets pesticide tolerances; CDC tracks outbreaks.

Question 6 · medium

A line has four steps in series with capacities 1200, 900, 1500 and 1000 kg/h. The line capacity and the utilisation of the 1500 kg/h step are

  1. 900 kg/h and 60 %
  2. 1500 kg/h and 100 %
  3. 900 kg/h and 40 %
  4. 1150 kg/h and 77 %
Answer and working

A. 900 kg/h and 60 %

Capacity is set by the bottleneck, 900 kg/h. Utilisation of the 1500 kg/h step = 900/1500 = 60 %. The mean of the capacities, 1150, is not a line capacity; 40 % is the idle fraction.

Question 7 · hard

Delivered equipment for a fluid-processing plant costs 2.0 million. Using the Lang factor for fluid-processing plants given in standard process-design texts, the estimated fixed capital investment is

  1. 9.48 million
  2. 0.42 million
  3. 6.20 million
  4. 7.26 million
Answer and working

A. 9.48 million

Lang factors: solid 3.10, solid–fluid 3.63, fluid 4.74. Fixed capital = 2.0 × 4.74 = 9.48 million. 7.26 uses the solid–fluid factor; 6.20 the solid factor. 0.42 million divides by the Lang factor instead of multiplying (2.0/4.74).

Question 8 · hard

A feasibility study shows positive NPV only when capacity utilisation exceeds 90 % every year. The sound conclusion is that

  1. The project is robust because NPV is positive at full capacity
  2. The project is fragile and its raw-material supply needs testing
  3. The discount rate should be lowered until NPV becomes positive
  4. Sensitivity analysis is unnecessary once NPV is positive
Answer and working

B. The project is fragile and its raw-material supply needs testing

Sensitivity analysis shows dependence on high utilisation, which seasonal raw-material supply rarely guarantees, so the project is risky. Adjusting the discount rate to fit the answer is not analysis.

Question 9 · medium

2000 kg/h of juice (cp = 3.9 kJ/kg·K) is cooled from 30 °C to 4 °C. Ignoring other loads, the refrigeration capacity needed is

  1. 4.6 TR
  2. 16.0 TR
  3. 56.3 TR
  4. 198.1 TR
Answer and working

B. 16.0 TR

Q = 2000 × 3.9 × 26/3600 = 56.3 kW; 56.3/3.517 = 16.0 TR. 56.3 is the load in kW mislabelled as TR; 198.1 multiplies by 3.517 instead of dividing. 4.6 TR divides by 3.517 twice.

Question 10 · medium

Why is steam, rather than hot water, the usual heating medium in food plants?

  1. It has a much higher specific heat than water in the liquid state at all pressures
  2. It delivers large latent heat at a temperature fixed by its pressure
  3. It cannot scald operators if a line ruptures
  4. It needs no condensate removal from heat exchangers
Answer and working

B. It delivers large latent heat at a temperature fixed by its pressure

Condensing steam releases its latent heat at constant temperature set by pressure, giving high heat-transfer rates and easy control. Condensate must be removed by traps, and steam is a scald hazard.

A study plan for Food Quality, Safety & Process Plant Design in NCEES PE Agricultural and Biological Engineering

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 59 questions): FSMA and HARPC concepts (10, 17%); Equipment sizing (9, 15%); Quality attributes and their measurement (7, 12%); HACCP (6, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Process flow sheets (6, 10%); Feasibility reports (4, 7%); GMP and hygiene (4, 7%); Hygienic design of equipment (4, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Food law: FSSAI, FDA and Codex (3, 5%); Plant location and layout (3, 5%); Waste and by-product utilisation (3, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Feasibility reports (3 hard of 4), Quality attributes and their measurement (4 hard of 7), Equipment sizing (4 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Food law: FSSAI, FDA and Codex (1 easy of 3); FSMA and HARPC concepts (2 easy of 10).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES PE Agricultural and Biological Engineering Food Quality, Safety & Process Plant Desi

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.