LAISHA
Open Laisha

NCEES PE Agricultural and Biological Engineering Machine Design: practice questions

NCEES PE Agricultural and Biological Engineering · USA · NCEES (ASABE is the content partner)

Original practice questions written to the published syllabus · not past papers
10worked here, free
36written to this exam in this subject
12syllabus units

About NCEES PE Agricultural and Biological Engineering

NCEES PE Agricultural and Biological Engineering is a licensing and registration exam run by NCEES (ASABE is the content partner), for candidates in USA. Computer-based, 85 questions, 9.5-hour appointment (8.5 hours of exam). Once a year (next: 28 Oct 2026). Closed book with the electronic NCEES handbook and supplied searchable ASABE standards; SI and US customary units.

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Machine Design in NCEES PE Agricultural and Biological Engineering

Machinery systems: component design with supplied references, including shafts, bearings, belts, chains, gears, fasteners and welds, often in US customary units, and power-transmission selection with service factors.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 36 NCEES PE Agricultural and Biological Engineering questions in this subject: 2 easy, 16 medium, 18 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES PE Agricultural and Biological Engineering and are not shown on any other exam's page.

Question 1 · medium

A designer applies a service factor of 1.75 to the nominal draft load of a subsoiler shank and then designs with a factor of safety of 2 on yield. A reviewer objects that the shank looks very heavy. What is the most defensible response?

  1. Check that the service factor and factor of safety do not both cover the same uncertainty, and base them on measured loads
  2. Double both factors, because subsoilers hit stones
  3. Design on ultimate strength instead of yield so that both factors can stay
  4. Remove the factor of safety entirely, because the service factor of 1.75 already covers every uncertainty in strength and load
Answer and working

A. Check that the service factor and factor of safety do not both cover the same uncertainty, and base them on measured loads

A service factor raises the load for known shock and duty; a factor of safety covers remaining uncertainty in strength, analysis and consequences. Stacking both for the same shock double-counts it and makes the part heavy. The fix is to justify each factor, ideally from measured field loads. Removing all margin, doubling both, or switching to ultimate strength without reason are not sound.

Question 2 · hard

A thresher shaft carries a bending moment of 600 N m and a torque of 800 N m at its critical section. Using the maximum shear stress theory with an allowable shear stress of 50 MPa, what is the required diameter?

  1. 52.2 mm
  2. 43.4 mm
  3. 58.8 mm
  4. 46.7 mm
Answer and working

D. 46.7 mm

Equivalent twisting moment Te = sqrt(M^2 + T^2) = sqrt(600^2 + 800^2) = 1000 N m. d^3 = 16 Te/(pi tau) = 16 x 1000000 / (pi x 50) gives d = 46.7 mm. Ignoring bending gives 43.4 mm (unsafe); adding M and T arithmetically gives 52.2 mm; using 32 instead of 16 gives 58.8 mm.

Question 3 · medium

A shaft with suddenly applied minor shock carries a bending moment of 400 N m and a torque of 300 N m. The combined shock and fatigue factors are 1.5 for bending and 1.0 for torsion. What equivalent twisting moment should be used in the ASME shaft equation?

  1. 602 N m
  2. 671 N m
  3. 500 N m
  4. 900 N m
Answer and working

B. 671 N m

Te = sqrt((Km M)^2 + (Kt T)^2) = sqrt((1.5 x 400)^2 + (1.0 x 300)^2) = sqrt(600^2 + 300^2) = 671 N m. Leaving out the factors gives 500 N m; adding the terms arithmetically gives 900 N m; swapping the factors gives 602 N m.

Question 4 · medium

A rotavator side-drive shaft keeps breaking after a few hundred hours with a fatigue fracture starting at the end of a keyway next to a shoulder. Which design change addresses the cause most directly?

  1. Increase the static factor of safety on yield without changing the geometry
  2. Change to a harder but more notch-sensitive steel with the same geometry, since higher hardness always raises fatigue strength at a notch
  3. Move the keyway end away from the shoulder, use a sled-runner keyway end and a larger shoulder fillet radius
  4. Weld the hub to the shaft to eliminate the key
Answer and working

C. Move the keyway end away from the shoulder, use a sled-runner keyway end and a larger shoulder fillet radius

The crack starts where two stress raisers overlap. Separating them and softening each (sled-runner keyway end, generous fillet) lowers Kf directly. A bigger static factor of safety does not target the notch. Welding onto a shaft adds a severe notch and residual stress. A harder steel is more notch-sensitive, so its gain in endurance limit is partly lost.

Question 5 · medium

A telescoping PTO shaft with a Hooke's joint at each end drives a rotary mower. The mower vibrates and the gearbox bearings fail early. Inspection shows the joint angles are equal but the two yokes on the intermediate shaft are 90 degrees out of line. What should be done?

  1. Leave the phasing and add a heavier flywheel to the mower
  2. Replace the shear bolt with a higher-grade bolt
  3. Reassemble the telescoping halves so that the intermediate-shaft yokes are in the same plane
  4. Increase the joint angles so that the shaft is more flexible and the speed fluctuations are absorbed by the telescoping tube
Answer and working

C. Reassemble the telescoping halves so that the intermediate-shaft yokes are in the same plane

Uniform output from a double Hooke's joint requires equal joint angles and intermediate yokes in phase (in the same plane). At 90 degrees the speed fluctuations add instead of cancelling, loading the gearbox cyclically. Larger angles make the fluctuation worse, and a stronger shear bolt removes overload protection.

Question 6 · medium

A cultivator tine spring is made of 8 mm wire with a mean coil diameter of 56 mm and 8 active coils. Take G = 80 GPa. What is its stiffness?

  1. 29.2 N/mm
  2. 3.6 N/mm
  3. 19.5 N/mm
  4. 23.3 N/mm
Answer and working

A. 29.2 N/mm

k = G d^4/(8 D^3 N) = 80000 x 8^4/(8 x 56^3 x 8) = 29.2 N/mm. Counting two extra end coils gives 23.3; using the outer diameter (64 mm) gives 19.5; d^3 in place of d^4 gives 3.6 N/mm.

Question 7 · hard

A lightly loaded journal bearing uses oil of viscosity 0.02 Pa s. The journal runs at 20 rev/s, the unit load on the projected area is 1 MPa, and the radius-to-radial-clearance ratio is 1000. What is the friction coefficient by Petroff's equation?

  1. 0.0039
  2. 0.0079
  3. 0.0025
  4. 0.474
Answer and working

B. 0.0079

f = 2 pi^2 (mu N/p)(r/c) = 2 x pi^2 x (0.02 x 20/10^6) x 1000 = 19.74 x 4 x 10^-4 = 0.0079. Using 2 pi instead of 2 pi^2 gives 0.0025; entering speed in rpm instead of rev/s gives 0.474. 0.0039 uses pi^2 without the factor 2.

Question 8 · medium

Insert ball bearings on a rotavator rotor fail within one season, full of fine dust. The calculated L10 life is five times the required life. What is the most likely remedy?

  1. Run the bearings dry to stop dust sticking to grease
  2. Choose a bearing with a still higher load rating (larger C), because the dust raises the equivalent dynamic load on the rolling elements
  3. Improve sealing (for example multi-lip or labyrinth seals) and set a regreasing schedule that purges contaminants
  4. Tighten the set-screws further
Answer and working

C. Improve sealing (for example multi-lip or labyrinth seals) and set a regreasing schedule that purges contaminants

The rating life assumes clean, well-lubricated conditions. Abrasive contamination wears the raceways long before fatigue, so a bigger bearing will fail the same way. Sealing and purging grease address the cause; running dry makes it worse.

Question 9 · hard

A V-belt has a maximum allowable tension of 1500 N, a mass of 0.4 kg/m, and runs at 25 m/s. The limiting tension ratio (T1 - Tc)/(T2 - Tc) is 3.0. What power can one belt transmit?

  1. 31.25 kW
  2. 25.00 kW
  3. 16.67 kW
  4. 20.83 kW
Answer and working

D. 20.83 kW

Tc = m v^2 = 0.4 x 25^2 = 250 N. Tension available for power = 1500 - 250 = 1250 N, and T1 - T2 = 1250 x (1 - 1/3.0) = 833 N. P = 833 x 25 = 20.83 kW. Ignoring Tc gives 25.00 kW, which overloads the belt. Using (T1 - Tc) v = 31.25 kW forgets the slack-side tension; subtracting Tc twice gives 16.67 kW.

Question 10 · hard

A shear pin passes diametrically through a 30 mm shaft and its hub, so it shears at two planes. The drive must break free at 150 N m. The pin's ultimate shear strength is 300 MPa. What pin diameter is needed?

  1. 4.61 mm
  2. 0.146 mm
  3. 6.51 mm
  4. 3.26 mm
Answer and working

A. 4.61 mm

T = 2 x (pi/4) d^2 tau u x D/2 = (pi/4) d^2 tau u D. d^2 = 4T/(pi tau u D) = 4 x 150000/(pi x 300 x 30) = 21.22 mm^2, d = 4.61 mm. Single shear gives 6.51 mm; counting four planes gives 3.26 mm; leaving torque in N m gives an absurd 0.146 mm.

A study plan for Machine Design in NCEES PE Agricultural and Biological Engineering

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 36 questions): Bolted joints (5, 14%); Overload safety devices: shear bolts and slip clutches (5, 14%); Rolling and sliding bearings and bearing life (4, 11%); Shafts under combined bending and torsion (4, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Belt and chain drives (3, 8%); Measurement of force, torque and strain on machine elements (3, 8%); Springs (3, 8%); Spur gear design (Lewis and Buckingham) (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Stress concentration and fatigue (Goodman and Soderberg) (2, 6%); Welded joints (2, 6%); Keys and couplings (1, 3%); The design process, materials and factor of safety (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Stress concentration and fatigue (Goodman and Soderberg) (2 hard of 2), Belt and chain drives (2 hard of 3), Springs (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Measurement of force, torque and strain on machine elements (1 easy of 3); Bolted joints (1 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES PE Agricultural and Biological Engineering Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.