NCEES FE Other Disciplines · USA · NCEES
Original practice questions written to the published syllabus · not past papersNCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).
Source: ncees.org.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.
Our 22 NCEES FE Other Disciplines questions in this subject: 12 easy, 8 medium, 2 hard, across 6 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.
For a ductile steel part under a steady (static) load, the allowable stress is normally obtained by dividing which property by the factor of safety?
B. Yield strength
A ductile part is taken to fail when it yields, because permanent deformation ends its usefulness, so allowable stress = yield strength / FoS. Ultimate strength is the basis for brittle materials, which do not yield. The endurance limit is the basis under fluctuating load, and the modulus of elasticity is a stiffness, not a strength.
Which theory of failure is generally recommended for brittle materials such as grey cast iron?
C. Maximum principal stress theory (Rankine)
Brittle materials fail by fracture when the largest normal stress reaches their strength, which the maximum principal stress theory models. The maximum shear stress and distortion energy theories describe yielding of ductile metals.
A point on a ductile steel shaft carries a bending stress of 80 MPa and a torsional shear stress of 50 MPa. The yield strength is 300 MPa. What is the factor of safety against yielding by the distortion energy (von Mises) theory?
D. 2.54
Von Mises equivalent stress = sqrt(sigma^2 + 3 tau^2) = sqrt(80^2 + 3 x 50^2) = 117.9 MPa, so N = 300 / 117.9 = 2.54. The maximum shear stress theory uses sqrt(sigma^2 + 4 tau^2) = 128.1 MPa and gives the more conservative 2.34. Using the largest principal stress (104.0 MPa) gives 2.88, which is the brittle-material criterion; ignoring shear gives 3.75.
A shoulder fillet has a theoretical stress concentration factor of 2.2 and the steel has a notch sensitivity of 0.8. What is the fatigue stress concentration factor?
A. 1.96
Kf = 1 + q (Kt - 1) = 1 + 0.8 x (2.2 - 1) = 1.96. Taking Kf = Kt (2.2) assumes full notch sensitivity (q = 1). Multiplying q x Kt gives 1.76, and dividing by q (2.50) inverts the relation.
A machined steel shaft has an ultimate tensile strength of 600 MPa. Estimate the polished-specimen endurance limit as half the ultimate strength, then apply a surface factor of 0.8 and a size factor of 0.85. What is the corrected endurance limit?
B. 204 MPa
Se' = 0.5 x 600 = 300 MPa; Se = ka kb Se' = 0.8 x 0.85 x 300 = 204 MPa. 300 MPa ignores the correction factors; 408 MPa applies them to Sut instead of Se'; 240 MPa forgets the size factor.
The bending stress at a point on a rotating tine shaft varies between +200 MPa and -50 MPa. What are the mean stress and stress amplitude?
D. Mean 75 MPa, amplitude 125 MPa
sigma m = (sigma max + sigma min)/2 = (200 - 50)/2 = 75 MPa; sigma a = (sigma max - sigma min)/2 = (200 + 50)/2 = 125 MPa. Swapping the two is a common slip, and 250 MPa is the stress range, which is twice the amplitude.
A solid steel shaft of 40 mm diameter and 1 m length carries a torque of 500 N m. Take G = 80 GPa. What is the angle of twist?
B. 1.42 degrees
J = pi d^4/32 = pi x 40^4/32 = 251327 mm^4. theta = TL/(GJ) = 500000 x 1000/(80000 x 251327) = 0.0249 rad = 1.42 degrees. Reporting radians as degrees gives 0.0249; using the area moment pi d^4/64 instead of the polar moment gives 2.85 degrees. 0.089 degrees enters the diameter in J = pi r^4/2 (pi x 40^4/2).
Two springs of stiffness 20 N/mm and 30 N/mm act side by side (in parallel) under a common rigid plate. What is the combined stiffness?
C. 50 N/mm
In parallel both springs have the same deflection and the forces add, so k = 20 + 30 = 50 N/mm. 12 N/mm is the series result. 25 N/mm is the average and 600 N/mm the product of the two stiffnesses.
A 120 ohm strain gauge with a gauge factor of 2.1 is bonded to a shaft that strains by 500 microstrain. What is the change in its resistance?
A. 0.126 ohm
delta R = GF x epsilon x R = 2.1 x 500 x 10^-6 x 120 = 0.126 ohm. Forgetting the gauge factor gives 0.060 ohm; 0.00105 is delta R/R, not delta R. 126 ohm treats microstrain as 10^-3.
Why is a three-element strain rosette used instead of a single gauge at some points on a welded frame?
D. Because the principal stress directions are unknown, and three strains in different directions give the principal strains and their directions
A single gauge reads strain only along its axis. Where the stress state is biaxial and the directions unknown, three readings (for example at 0, 45 and 90 degrees) fix the two principal strains and their orientation, from which principal stresses follow.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.