LAISHA
Open Laisha

NCEES FE Other Disciplines Instrumentation, Sensors & Process Control: practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
35written to this exam in this subject
9syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Instrumentation, Sensors & Process Control in NCEES FE Other Disciplines

Sensors and transducers, bridge circuits, sampling and ADC resolution, block diagrams, closed-loop transfer functions, steady-state error, stability and first- and second-order response.

Measuring temperature, pressure, flow, force and moisture, logging the data, and controlling processes automatically.

Our 35 NCEES FE Other Disciplines questions in this subject: 6 easy, 24 medium, 5 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

A flow measurement has three independent uncertainty components: ±0.4%, ±0.3% and ±1.2%. What is the most probable (root-sum-square) combined uncertainty?

  1. ±1.9%
  2. ±1.69%
  3. ±0.63%
  4. ±1.3%
Answer and working

D. ±1.3%

Independent uncertainties combine as √(0.4² + 0.3² + 1.2²) = √1.69 = 1.30 ≈ ±1.3%. ±1.9% is the arithmetic (worst-case) sum, 1.69 forgets the square root, and 0.63 is merely the average of the three.

Question 2 · medium

A sensor behaves as a 2.00 V source with 50 kΩ internal resistance. It is read with a voltmeter of 1 MΩ input resistance. What will the voltmeter show?

  1. 2.000 V
  2. 2.100 V
  3. 1.000 V
  4. 1.905 V
Answer and working

D. 1.905 V

Loading: the meter forms a divider with the source, so it reads V·Rm/(Rs + Rm) = 2.00 × 1000/1050 = 1.905 V, about 4.8% low. 2.000 V would need an infinite meter resistance; 2.100 V adds the 5% instead of losing it; 1.000 V would be the result only if the two resistances were equal.

Question 3 · medium

An NTC thermistor has R = 10.0 kΩ at 25 °C and β = 3950 K. Using the beta equation, what is its resistance at 50 °C?

  1. 3.59 kΩ
  2. 27.9 kΩ
  3. 5.00 kΩ
  4. 20.0 kΩ
Answer and working

A. 3.59 kΩ

R = R0·exp[β(1/T − 1/T0)] with kelvin: 1/323.15 − 1/298.15 = −0.000259 K⁻¹; × 3950 = −1.025; e^that = 0.3588; R = 3.59 kΩ. 27.9 kΩ reverses the sign (an NTC falls in resistance as it warms); 5.00 kΩ assumes resistance halves linearly with doubled Celsius temperature, and 20 kΩ treats it as a PTC.

Question 4 · medium

A type K thermocouple (take 41 µV/°C as constant) on a dryer plenum gives 1.64 mV. The reference junction at the logger terminals is at 25 °C. Estimate the plenum temperature.

  1. 40 °C
  2. 15 °C
  3. 65 °C
  4. 29 °C
Answer and working

C. 65 °C

The emf measures the difference between junctions: 1.64 mV / 0.041 mV/°C = 40 °C above the reference, so T ≈ 40 + 25 = 65 °C. Reporting 40 °C omits cold-junction compensation; 15 °C subtracts it; 29 °C makes a factor-of-ten unit slip before adding 25 °C. In real work, convert the reference temperature to emf and use the standard reference table, because the sensitivity is not exactly constant.

Question 5 · easy

A pump delivery gauge reads 150 kPa and the local atmospheric pressure is 101.3 kPa. What is the absolute pressure?

  1. 48.7 kPa
  2. 150.0 kPa
  3. 101.3 kPa
  4. 251.3 kPa
Answer and working

D. 251.3 kPa

Absolute = gauge + atmospheric = 150 + 101.3 = 251.3 kPa. 48.7 kPa subtracts atmospheric pressure; 150 kPa is the gauge reading itself.

Question 6 · hard

A venturi meter on an irrigation main has a 100 mm inlet and 50 mm throat, with Cd = 0.98. Measured Δp between inlet and throat is 20 kPa on water (ρ = 1000 kg/m³). What is the flow rate?

  1. 12.17 L/s
  2. 50.3 L/s
  3. 7.82 L/s
  4. 12.57 L/s
Answer and working

D. 12.57 L/s

A2 = π(0.05)²/4 = 0.001963 m²; β = 0.5, 1 − β⁴ = 0.9375. Q = Cd A2 √(2Δp/(ρ(1 − β⁴))) = 0.98 × 0.001963 × √(40000/937.5) = 0.01257 m³/s = 12.57 L/s. 12.17 L/s omits the velocity-of-approach factor (1 − β⁴); 50.3 L/s uses the inlet area in place of the throat; 7.82 L/s uses an orifice coefficient of 0.61.

Question 7 · medium

A Pitot-static tube in the inlet duct of a batch grain dryer shows a velocity pressure of 150 Pa. Air density is 1.2 kg/m³. What is the local air velocity?

  1. 250 m/s
  2. 15.8 m/s
  3. 11.2 m/s
  4. 0.55 m/s
Answer and working

B. 15.8 m/s

v = √(2Δp/ρ) = √(2 × 150/1.2) = √250 = 15.8 m/s. 250 m/s forgets the square root; 11.2 m/s drops the factor 2; 0.55 m/s uses the density of water.

Question 8 · medium

A quarter-bridge strain-gauge circuit is excited at 10 V. The gauge factor is 2.1 and the strain is 800 µε. What is the approximate bridge output?

  1. 4.2 mV
  2. 16.8 mV
  3. 8.4 mV
  4. 42 mV
Answer and working

A. 4.2 mV

Quarter bridge: Vo ≈ Vs·GF·ε/4 = 10 × 2.1 × 800×10⁻⁶/4 = 0.0042 V = 4.2 mV. 16.8 mV is the full-bridge value, 8.4 mV the half-bridge value; 42 mV is a decimal slip.

Question 9 · medium

A steel hitch link (E = 200 GPa) with a 400 mm² cross-section carries an axial pull of 20 kN. What axial strain will a gauge on it read?

  1. 50 µε
  2. 2500 µε
  3. 25 µε
  4. 250 µε
Answer and working

D. 250 µε

σ = F/A = 20 000/400×10⁻⁶ = 50 MPa; ε = σ/E = 50×10⁶/200×10⁹ = 0.000250 = 250 µε. 50 µε confuses the stress number with strain; 2500 and 25 µε are factor-of-ten slips in the area or modulus.

Question 10 · hard

A closed-loop system has the characteristic equation s³ + 2s² + 3s + K = 0. For what range of K is it stable?

  1. 0 < K < 3
  2. K > 6
  3. 0 < K < 6
  4. 0 < K < 1.5
Answer and working

C. 0 < K < 6

Routh array: rows s³ (1, 3), s² (2, K), s¹ ((2·3 − K)/2), s⁰ (K). All first-column entries must be positive: 6 − K > 0 and K > 0, so 0 < K < 6. For a cubic with positive coefficients the condition is a2·a1 > a0: 2 × 3 > K.

A study plan for Instrumentation, Sensors & Process Control in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 35 questions): Control modes: on-off, P, PI and PID (8, 23%); Signal conditioning (6, 17%); Pressure, flow and level measurement (5, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Static and dynamic characteristics of instruments (4, 11%); Data acquisition and data loggers (3, 9%); Temperature transducers (3, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: The generalised measurement system (3, 9%); Force, torque and strain: strain gauges and load cells (2, 6%); Programmable logic controllers (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Control modes: on-off, P, PI and PID (2 hard of 8), Static and dynamic characteristics of instruments (1 hard of 4), Pressure, flow and level measurement (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Signal conditioning (3 easy of 6); Pressure, flow and level measurement (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Instrumentation, Sensors & Process Control

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.