LAISHA
Open Laisha

NCEES FE Other Disciplines Strength of Materials: practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
63written to this exam in this subject
12syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Strength of Materials in NCEES FE Other Disciplines

9–14 of 110 questions. Short numericals solved with the NCEES Reference Handbook: axial stress and deformation, thermal stress, shear and moment diagrams, bending and transverse shear stress, torsion of circular shafts, beam deflection by superposition from handbook tables, Euler buckling with effective length, thin-walled pressure vessels, Mohr's circle and principal stresses, and failure criteria. Speed with units and knowing where each formula sits in the handbook decide the score.

How members carry load: stress, strain, bending, torsion, deflection and buckling, used in machine and structure design.

Our 63 NCEES FE Other Disciplines questions in this subject: 18 easy, 32 medium, 13 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

For an aluminium alloy used in a sprayer frame, which has no distinct yield point, the yield strength quoted by a supplier is usually the:

  1. Stress at which the specimen necks, taken from the maximum load
  2. Stress at the limit of proportionality, read at 0.02 percent strain
  3. Stress at fracture divided by the conventional factor of two
  4. Stress at 0.2 percent offset strain, drawn parallel to the elastic line
Answer and working

D. Stress at 0.2 percent offset strain, drawn parallel to the elastic line

Materials without a sharp yield point are given a proof stress: draw a line parallel to the initial elastic slope from 0.2 percent strain and read the stress where it cuts the curve. Necking begins at the ultimate stress, not yield, and dividing fracture stress by two is not a definition of yield.

Question 2 · medium

A 20 mm pin passes through a 12 mm thick plate lug on a trailer chassis and transfers 24 kN. The bearing stress between the pin and the lug is:

  1. 76.4 MPa
  2. 31.8 MPa
  3. 100 MPa
  4. 50 MPa
Answer and working

C. 100 MPa

Bearing stress uses the projected area d × t: 24,000/(20 × 12) = 100 MPa. P/(πd²/4) = 76.4 MPa is the shear stress in the pin, and P/(πdt) = 31.8 MPa uses the full cylindrical surface, not the projected area. 50 MPa wrongly halves the load as if the pin bore in two lugs (24,000/(2 × 20 × 12)).

Question 3 · medium

A steel bar (E = 200 GPa, ν = 0.3) carries a uniaxial tensile stress of 100 MPa. Its volumetric strain is:

  1. 5.0 × 10⁻⁴
  2. 8.0 × 10⁻⁴
  3. 1.5 × 10⁻³
  4. 2.0 × 10⁻⁴
Answer and working

D. 2.0 × 10⁻⁴

ε = 100/200,000 = 5.0e-04. For uniaxial stress, ε_v = ε(1 − 2ν) = 5.0e-04 × 0.4 = 2.0e-04. Using (1 + 2ν) adds the lateral strains instead of subtracting them; 3ε treats the bar like a sphere under hydrostatic stress.

Question 4 · medium

A 20 m steel irrigation pipe (α = 12 × 10⁻⁶ per °C, E = 200 GPa) is laid with a 3 mm expansion gap and then heats by 35 °C, with the far end anchored. The stress in the pipe is:

  1. 54 MPa
  2. 84 MPa
  3. 30 MPa
  4. 114 MPa
Answer and working

A. 54 MPa

Free expansion = 12 × 10⁻⁶ × 20,000 × 35 = 8.4 mm. The gap absorbs 3 mm, so 5.4 mm is blocked: σ = 200,000 × 5.4/20,000 = 54 MPa. Ignoring the gap gives 84 MPa. 114 MPa adds the gap to the free expansion instead of subtracting it (11.4 mm).

Question 5 · easy

Along a beam, the maximum bending moment occurs at the section where:

  1. The shear force reaches its maximum value
  2. The applied load intensity is the greatest
  3. The shear force is zero or changes sign
  4. The slope of the shear force diagram is zero
Answer and working

C. The shear force is zero or changes sign

Because dM/dx = V, the bending moment is stationary where V = 0 or changes sign. The shear force is usually largest at the supports, where the moment of a simply supported beam is zero.

Question 6 · medium

A solid 40 mm round pin used as a short beam carries a transverse shear force of 10 kN. The maximum transverse shear stress is closest to:

  1. 10.61 MPa
  2. 7.96 MPa
  3. 11.94 MPa
  4. 15.92 MPa
Answer and working

A. 10.61 MPa

τ_avg = 10,000/(π × 40²/4) = 7.96 MPa. For a solid circle τ_max = (4/3)τ_avg = 10.61 MPa at the neutral axis; 1.5 is the rectangle factor. 11.94 MPa uses the rectangle factor 1.5, and 15.92 MPa uses the thin-walled tube factor 2.

Question 7 · medium

A sprayer boom arm is a 3 m steel cantilever (E = 200 GPa, I = 1.0 × 10⁶ mm⁴) with a 200 N nozzle cluster at its tip. Ignoring self-weight, the tip deflection is:

  1. 9.0 mm
  2. 3.375 mm
  3. 0.562 mm
  4. 27.0 mm
Answer and working

A. 9.0 mm

δ = WL³/(3EI) = 200 × 3000³/(3 × 200,000 × 10⁶) = 9.0 mm. WL³/(48EI) is the simply supported central-load result. WL³/(8EI) gives 3.375 mm, WL³/(48EI) gives 0.562 mm, and dropping the 3 gives 27.0 mm.

Question 8 · easy

On a principal plane, the shear stress is:

  1. Maximum
  2. Equal to half the normal stress
  3. Equal to the average normal stress
  4. Zero
Answer and working

D. Zero

Principal planes are defined as the planes of zero shear; on them the normal stress is an extreme. Maximum shear planes lie at 45° to them.

Question 9 · medium

A bar carries a uniaxial tensile stress σ. The maximum shear stress in the bar and the plane on which it acts are:

  1. σ/2, on planes at 45° to the bar axis
  2. σ, on planes at 45° to the bar axis
  3. σ/2, on planes perpendicular to the axis
  4. Zero, since only normal stress is applied
Answer and working

A. σ/2, on planes at 45° to the bar axis

Mohr's circle for uniaxial stress passes through 0 and σ, so its radius σ/2 is the maximum shear, found at 45°. That is why ductile bars show slip lines at 45° in tension.

Question 10 · medium

A 2 m steel tie (area 500 mm², E = 200 GPa) carries a gradually applied load of 50 kN. The strain energy stored is:

  1. 50 J
  2. 25 J
  3. 25,000 J
  4. 100 J
Answer and working

B. 25 J

U = P²L/(2AE) = 50,000² × 2000/(2 × 500 × 200,000) = 25,000 N·mm = 25 J. Forgetting the ½ gives 50 J (a suddenly applied load would double the stress and give 100 J); not converting N·mm to J gives 25,000.

A study plan for Strength of Materials in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (41% of the 63 questions): Stress, strain and Hooke's law (8, 13%); Columns: Euler and Rankine formulas (6, 10%); Combined stresses and Mohr's circle (6, 10%); Shear force and bending moment diagrams (6, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Theories of failure (6, 10%); Bending and shear stresses in beams (5, 8%); Thermal stresses (5, 8%); Thin cylinders and spheres (5, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Deflection of beams (4, 6%); Elastic constants and their relations (4, 6%); Strain energy (4, 6%); Torsion of circular shafts (4, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Thin cylinders and spheres (2 hard of 5), Columns: Euler and Rankine formulas (2 hard of 6), Theories of failure (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Thin cylinders and spheres (3 easy of 5); Torsion of circular shafts (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Strength of Materials

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.