LAISHA
Open Laisha

NCEES FE Other Disciplines Heat & Mass Transfer: practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
11syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Heat & Mass Transfer in NCEES FE Other Disciplines

Conduction, convection, radiation, heat exchangers and diffusion — the physics of drying, cooling, freezing and cold-store walls.

Our 42 NCEES FE Other Disciplines questions in this subject: 14 easy, 28 medium, 0 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

Air (ν = 1.5 × 10⁻⁵ m²/s) flows at 5 m/s along a long flat plate. Taking the critical Reynolds number for transition as 5 × 10⁵, the boundary layer becomes turbulent at a distance from the leading edge of about

  1. 6.9 mm
  2. 15 m
  3. 0.15 m
  4. 1.5 m
Answer and working

D. 1.5 m

x_c = Re_c ν/V = 5 × 10⁵ × 1.5 × 10⁻⁵/5 = 1.5 m. Using the pipe value 2,300 gives 6.9 mm; using 5 × 10⁶ gives 15 m; 0.15 m is a factor-of-ten slip.

Question 2 · easy

The Stefan–Boltzmann constant σ has the value

  1. 5.67 × 10⁻⁸ W/m²·K⁴
  2. 5.67 × 10⁻⁸ W/m²·K
  3. 2,898 µm·K
  4. 1.38 × 10⁻²³ J/K
Answer and working

A. 5.67 × 10⁻⁸ W/m²·K⁴

E_b = σT⁴ with σ = 5.67 × 10⁻⁸ W/m²·K⁴. The unit must carry K⁴ because T is raised to the fourth power. 2,898 µm·K is Wien's displacement constant and 1.38 × 10⁻²³ J/K is Boltzmann's constant.

Question 3 · medium

Two large parallel grey plates face each other: one at 800 K with emissivity 0.8, the other at 500 K with emissivity 0.6. The net radiant heat flux between them is closest to

  1. 19,700 W/m²
  2. 10,300 W/m²
  3. 9,450 W/m²
  4. 15,700 W/m²
Answer and working

B. 10,300 W/m²

q = σ(T1⁴ − T2⁴)/(1/ε1 + 1/ε2 − 1) = 5.67 × 10⁻⁸ × (4.10 × 10¹¹ − 6.25 × 10¹⁰)/(1.25 + 1.667 − 1) = 19,700/1.917 = 10,300 W/m². Treating both as black gives 19,700; multiplying the emissivities gives 9,450, which ignores reflections; using ε1 alone is the small-body-in-enclosure formula, which does not apply to parallel plates. Using ε1 alone gives 15,700 W/m².

Question 4 · medium

Surface 1 has an area of 2 m² and surface 2 an area of 5 m². The view factor F12 is 0.6. The view factor F21 is

  1. 1.50
  2. 0.40
  3. 0.60
  4. 0.24
Answer and working

D. 0.24

Reciprocity: A1F12 = A2F21, so F21 = 2 × 0.6/5 = 0.24. Inverting the area ratio gives 1.50, which is impossible because a view factor cannot exceed 1; 1 − F12 misapplies the summation rule, which works across all surfaces seen from one surface, not between two surfaces. 1 − F12 gives 0.40.

Question 5 · easy

The lumped-capacitance method for transient conduction is generally acceptable when the Biot number, based on L_c = V/A_s, is

  1. greater than 0.1
  2. less than 10
  3. less than 0.1
  4. equal to the Fourier number
Answer and working

C. less than 0.1

Bi = hL_c/k compares internal conduction resistance with external convection resistance. When Bi < 0.1 the internal temperature differences are small, so the body can be treated as one lump. A large Bi means large internal gradients.

Question 6 · medium

In a counterflow heat exchanger the hot fluid is cooled from 120 °C to 70 °C and the cold fluid is heated from 20 °C to 60 °C. The log mean temperature difference is closest to

  1. 54.8 °C
  2. 55.0 °C
  3. 39.1 °C
  4. 43.4 °C
Answer and working

A. 54.8 °C

Counterflow: ΔT1 = 120 − 60 = 60 °C, ΔT2 = 70 − 20 = 50 °C. LMTD = (60 − 50)/ln(60/50) = 54.85 °C. The arithmetic mean, 55.0 °C, slightly overestimates it. Pairing the terminals as in parallel flow (100 and 10 °C) gives 39.1 °C; 43.4 °C does not follow from either terminal pairing (dividing ΔT1 alone by the logarithm would give 329 °C).

Question 7 · medium

A 1-shell-pass, 2-tube-pass exchanger has U = 500 W/m²·K and A = 10 m². The counterflow LMTD for its terminal temperatures is 40 °C and the correction factor from the chart is F = 0.90. Its duty is

  1. 180 kW
  2. 200 kW
  3. 222 kW
  4. 162 kW
Answer and working

A. 180 kW

Q = UAF·ΔT_lm,cf = 500 × 10 × 0.90 × 40 = 180000 W = 180 kW. Omitting F gives 200 kW; dividing by F gives 222 kW. F ≤ 1 because multipass flow is less effective than pure counterflow. 162 kW applies F twice.

Question 8 · easy

In the effectiveness–NTU method, the number of transfer units is defined as

  1. UA/C_max
  2. C_min/C_max
  3. Q/Q_max
  4. UA/C_min
Answer and working

D. UA/C_min

NTU = UA/C_min measures the thermal size of the exchanger. C_min/C_max is the capacity ratio C_r, and Q/Q_max is the effectiveness ε.

Question 9 · medium

A small grey body (emissivity 0.7) is placed inside a large enclosure. Compared with an identical black body at the same temperature in the same enclosure, its net radiative heat loss is

  1. the same as that of the black body
  2. 0.7 times that of the black body
  3. 1/0.7 times that of the black body
  4. 0.49 times that of the black body
Answer and working

B. 0.7 times that of the black body

For a small body in a large enclosure Q = εAσ(T1⁴ − T2⁴): the enclosure behaves as a black body because almost nothing it receives from the small body is reflected back. Loss scales with ε directly. 0.49 (ε²) wrongly applies the emissivity twice.

Question 10 · medium

The fin efficiency of a straight fin is defined as the ratio of

  1. the heat transferred with the fin to the heat transferred from the base area without the fin
  2. the fin tip temperature excess to the base temperature excess
  3. the heat transferred by the fin to the heat transferred by an infinitely long fin of the same cross-section, material and base temperature
  4. the actual heat transferred by the fin to the heat it would transfer if its entire surface were at the base temperature
Answer and working

D. the actual heat transferred by the fin to the heat it would transfer if its entire surface were at the base temperature

Efficiency compares the real fin with an ideal fin of infinite conductivity. The ratio with and without the fin is fin effectiveness, a different measure. The tip-to-base temperature ratio is 1/cosh(mL) for an insulated tip, and the ratio to an infinite fin is tanh(mL).

A study plan for Heat & Mass Transfer in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (57% of the 42 questions): Radiation: Stefan-Boltzmann law and view factors (8, 19%); Convection and dimensionless numbers (Nu, Re, Pr) (7, 17%); Heat exchangers: LMTD method (5, 12%); Extended surfaces (fins) (4, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Heat exchangers: effectiveness-NTU method (4, 10%); Steady conduction through plane walls and cylinders (4, 10%); Composite walls and critical radius of insulation (3, 7%); Condensation and boiling (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Diffusive mass transfer and Fick's law (2, 5%); Transient conduction: lumped capacity and Heisler charts (2, 5%); Convective mass transfer (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Heat exchangers: effectiveness-NTU method (2 easy of 4); Steady conduction through plane walls and cylinders (2 easy of 4).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.