LAISHA
Open Laisha

NCEES FE Other Disciplines Engineering Physics & Chemistry: practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
79written to this exam in this subject
6syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Physics & Chemistry in NCEES FE Other Disciplines

The physics and chemistry behind materials, water, fuels and electronics that later engineering subjects assume.

Our 79 NCEES FE Other Disciplines questions in this subject: 25 easy, 36 medium, 18 hard, across 6 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

In chlorinating a village water supply that contains some ammonia, why is the dose taken beyond the breakpoint?

  1. Beyond it, all the dissolved salts in the water precipitate and settle in the tank
  2. Beyond it, chlorine removes permanent hardness by forming insoluble calcium chloride
  3. Beyond it, chloramines are destroyed and added chlorine stays as a free residual
  4. Beyond it, residual chlorine falls to zero so the water has no taste or odour left
Answer and working

C. Beyond it, chloramines are destroyed and added chlorine stays as a free residual

As chlorine is added it first forms chloramines with ammonia; further chlorine destroys them and the residual dips to the breakpoint, after which free chlorine accumulates and keeps protecting the supply. Chlorination does not remove hardness, and calcium chloride is soluble.

Question 2 · medium

A downdraft gasifier runs on maize cobs with air as the gasifying agent. Which gas mixture best describes its producer gas?

  1. Mainly N2 with CO and H2, plus CO2 and a little CH4
  2. Mainly CH4 with CO2 and traces of H2S from the digestion
  3. Mainly CO2 and water vapour, with almost no combustible gas
  4. Mainly H2 and O2, which recombine to give water at the engine
Answer and working

A. Mainly N2 with CO and H2, plus CO2 and a little CH4

Partial oxidation with air leaves about half the gas as nitrogen; the combustibles are mainly CO and H2 with a little methane, so the heating value is low. Methane with CO2 and H2S describes biogas from anaerobic digestion; CO2 and water are the products of complete combustion.

Question 3 · easy

What distinguishes the gross (higher) calorific value of a fuel from its net (lower) calorific value?

  1. Gross includes the heat of the ash, while net counts only the heat of the volatile matter
  2. Gross includes the latent heat recovered when the water formed in combustion condenses
  3. Gross is measured at constant pressure and net at constant volume in a sealed vessel
  4. Gross is for dry fuel only, while net applies to the same fuel with all its ash removed
Answer and working

B. Gross includes the latent heat recovered when the water formed in combustion condenses

The water produced from the fuel's hydrogen (and its moisture) gives up its latent heat only if it condenses. Gross value counts that heat; net value assumes the water leaves as vapour. Constant-volume versus constant-pressure differences are small and are not what the two terms mean.

Question 4 · medium

A coal has C 80%, H 5%, O 6%, S 1% by mass. Using Dulong's formula HCV = [8,080 C + 34,500 (H − O/8) + 2,240 S]/100 kcal/kg, what is its gross calorific value?

  1. About 7688 kcal/kg
  2. About 7930 kcal/kg
  3. About 8211 kcal/kg
  4. About 7953 kcal/kg
Answer and working

D. About 7953 kcal/kg

Available hydrogen = 5 − 6/8 = 4.25%. HCV = (8,080 × 80 + 34,500 × 4.25 + 2,240 × 1)/100 = (646,400 + 146,625 + 2,240)/100 = 7953 kcal/kg. Ignoring the oxygen correction gives 8211; dropping sulphur gives 7930; 7688 is the net value.

Question 5 · medium

A diesel pump-set engine delivers 30 kW brake power at a brake thermal efficiency of 30%. The fuel's net calorific value is 42 MJ/kg. What is its fuel consumption?

  1. About 8.57 kg/h
  2. About 2.38 kg/h
  3. About 0.77 kg/h
  4. About 2.57 kg/h
Answer and working

A. About 8.57 kg/h

Fuel power = 30/0.30 = 100 kW; fuel flow = 100/42,000 = 0.00238 kg/s × 3,600 = 8.57 kg/h. Multiplying by the efficiency instead of dividing gives 0.77; ignoring efficiency gives 2.57; 2.38 is the flow in g/s mislabelled as kg/h.

Question 6 · medium

A steel tank is half full of water and left standing. Where does differential-aeration corrosion attack most strongly, and why?

  1. Just above the waterline, where oxygen is richer and the metal becomes the anode
  2. Evenly over the wetted area, because the whole immersed steel has one potential
  3. Just below the waterline, where oxygen is poorer and the metal becomes the anode
  4. At the tank bottom only, because water pressure there pushes ions into the steel
Answer and working

C. Just below the waterline, where oxygen is poorer and the metal becomes the anode

Areas with less oxygen become anodic relative to well-aerated areas, which act as cathodes; just below the waterline (and under deposits) the steel corrodes. The well-aerated zone near the surface is the cathode, so it is protected rather than attacked.

Question 7 · medium

Nylon-6,6 is formed from which pair of monomers, and by what type of polymerisation?

  1. Hexamethylenediamine and adipic acid, by condensation with loss of water
  2. Caprolactam alone, by condensation with loss of hydrogen chloride
  3. Phenol and formaldehyde, by addition giving a linear thermoplastic
  4. Ethylene glycol and terephthalic acid, by addition with no by-product
Answer and working

A. Hexamethylenediamine and adipic acid, by condensation with loss of water

Nylon-6,6 is a polyamide from hexamethylenediamine (six carbons) and adipic acid (six carbons), each amide link releasing water. Ethylene glycol and terephthalic acid give PET (also by condensation); caprolactam gives nylon-6 by ring-opening; phenol and formaldehyde give a thermosetting resin.

Question 8 · medium

Drip laterals are commonly extruded from which polymer, and why?

  1. Polystyrene, because its brittleness lets emitters be punched in easily
  2. Linear low-density polyethylene, for its flexibility, toughness and low cost
  3. Unplasticised PVC, because it bends easily into coils on reels
  4. Thermoset phenolic resin, because it can be heat-welded in the field
Answer and working

B. Linear low-density polyethylene, for its flexibility, toughness and low cost

Laterals must bend, be coiled, resist punctures and cost little, so LLDPE/LDPE blends are standard. Polystyrene is brittle; phenolic resins are thermosets that cannot be heat-welded; unplasticised PVC is rigid and is used for mains, not coiled laterals.

Question 9 · easy

A farm collects empty containers marked with the resin identification code 2. Which polymer are they?

  1. Polyethylene terephthalate
  2. Polyvinyl chloride
  3. High-density polyethylene
  4. Polypropylene
Answer and working

C. High-density polyethylene

The codes are 1 PET, 2 HDPE, 3 PVC, 4 LDPE, 5 PP, 6 PS, 7 other. Pesticide containers and water tanks are commonly HDPE.

Question 10 · medium

Why is open burning of waste PVC pipe and film on a farm especially harmful compared with burning polyethylene?

  1. PVC releases methane, which is more harmful than smoke from polyethylene
  2. PVC releases hydrogen chloride and chlorinated compounds as well as smoke
  3. PVC releases only fine silica ash, which damages the soil after burning
  4. PVC releases only water and carbon dioxide, but in very much larger volumes
Answer and working

B. PVC releases hydrogen chloride and chlorinated compounds as well as smoke

PVC contains about 57% chlorine by mass; burning it gives hydrogen chloride and can form chlorinated organic pollutants, in addition to the smoke all plastics give. Clean combustion to CO2 and water is not what happens in an open fire, and methane is not the characteristic product.

A study plan for Engineering Physics & Chemistry in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (35% of the 79 questions): Water chemistry: hardness, pH and treatment (15, 19%); Calorific value of fuels (13, 16%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Electrochemistry and batteries (13, 16%); Fuels and combustion chemistry (13, 16%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Polymers and plastics used in agriculture (13, 16%); Corrosion and its control (12, 15%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Water chemistry: hardness, pH and treatment (5 hard of 15), Fuels and combustion chemistry (4 hard of 13), Corrosion and its control (3 hard of 12).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Electrochemistry and batteries (5 easy of 13); Water chemistry: hardness, pH and treatment (5 easy of 15).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Engineering Physics & Chemistry

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.