LAISHA
Open Laisha

CUET-UG for B.Tech Agricultural Engineering Engineering Physics & Chemistry: practice questions

CUET-UG (ICAR 20% All-India Quota) for B.Tech Agricultural Engineering · India · National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
89written to this exam in this subject
8syllabus units

About CUET-UG for B.Tech Agricultural Engineering

CUET-UG (ICAR 20% All-India Quota) for B.Tech Agricultural Engineering is a university entrance exam run by National Testing Agency, for candidates in India. CUET-UG domain tests; the exact subject combination for B.Tech Agricultural Engineering was not verified.

Official site: exams.nta.ac.in.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Engineering Physics & Chemistry in CUET-UG for B.Tech Agricultural Engineering

The physics and chemistry behind materials, water, fuels and electronics that later engineering subjects assume.

Our 89 CUET-UG for B.Tech Agricultural Engineering questions in this subject: 29 easy, 39 medium, 21 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to CUET-UG for B.Tech Agricultural Engineering and are not shown on any other exam's page.

Question 1 · medium

In a Young's double-slit experiment, sodium light of wavelength 589 nm passes through slits 0.40 mm apart and the screen is 1.2 m away. What is the fringe width?

  1. 0.0002 mm
  2. 17.7 mm
  3. 0.88 mm
  4. 1.77 mm
Answer and working

D. 1.77 mm

β = λD/d = (589 × 10⁻⁹ × 1.2)/(0.40 × 10⁻³) = 1.76700 × 10⁻³ m = 1.77 mm. Half that (0.88 mm) is the spacing from a bright fringe to the next dark one; inverting D and d gives a far too small value; 17.7 mm is a unit slip. 0.0002 mm is that inverted value (λd/D).

Question 2 · medium

A well water contains, per litre, 162 mg Ca(HCO3)2, 120 mg MgSO4, 111 mg CaCl2 and 58.5 mg NaCl. What are its temporary and permanent hardness, as mg/L CaCO3?

  1. Temporary 162, permanent 231
  2. Temporary 100, permanent 250
  3. Temporary 100, permanent 200
  4. Temporary 200, permanent 100
Answer and working

C. Temporary 100, permanent 200

Convert with mass × 50/equivalent weight: Ca(HCO3)2 162 × 50/81 = 100 (temporary); MgSO4 120 × 50/60 = 100 and CaCl2 111 × 50/55.5 = 100 (permanent, total 200). NaCl causes no hardness, so adding 50 for it is wrong; 162 and 231 are raw salt masses, not CaCO3 equivalents.

Question 3 · easy

Rainwater collected from a roof has a hydrogen-ion concentration of 3.2 × 10⁻⁶ mol/L. What is its pH?

  1. 6.49
  2. 8.51
  3. 12.65
  4. 5.49
Answer and working

D. 5.49

pH = −log10(3.2 × 10⁻⁶) = 6 − 0.505 = 5.49. 8.51 is the pOH; 12.65 uses the natural logarithm instead of base 10. 6.49 uses an exponent of −7 instead of −6.

Question 4 · hard

A liquid fuel contains 84% carbon and 16% hydrogen by mass. Taking air as 23% oxygen by mass, what is the minimum (stoichiometric) mass of air per kg of fuel?

  1. 12.5 kg
  2. 16.8 kg
  3. 3.52 kg
  4. 15.3 kg
Answer and working

D. 15.3 kg

O2 = (32/12)(0.84) + 8(0.16) = 2.24 + 1.28 = 3.52 kg; air = 3.52/0.23 = 15.3 kg. 3.52 kg is the oxygen alone; dividing by 0.21 uses the volume fraction with a mass basis; 12.5 kg uses 4 instead of 8 kg O2 per kg H. Dividing by 0.21 gives 16.8 kg.

Question 5 · medium

A biogas-fired water heater burns pure methane with 20% excess air. How much air is supplied per m³ of methane (same temperature and pressure; air 21% O2 by volume)?

  1. 11.43 m³
  2. 9.72 m³
  3. 9.52 m³
  4. 2.40 m³
Answer and working

A. 11.43 m³

Theoretical air = 2/0.21 = 9.52 m³; with 20% excess, actual = 1.2 × 9.52 = 11.43 m³. 9.52 m³ omits the excess; adding 0.2 m³ treats 20% as an absolute amount; 2.40 m³ is the total oxygen supplied, not air. Adding 0.2 m³ gives 9.72 m³.

Question 6 · hard

A batch dryer must remove 1,000 kg of water from paddy. Take 2.5 MJ of heat per kg of water evaporated, an overall furnace-plus-dryer efficiency of 50%, and rice husk with a net calorific value of 13 MJ/kg. About how much husk is burnt?

  1. About 96 kg
  2. About 192 kg
  3. About 385 kg
  4. About 10400 kg
Answer and working

C. About 385 kg

Heat to water = 1,000 × 2.5 = 2,500 MJ; fuel heat = 2,500/0.50 = 5,000 MJ; husk = 5,000/13 = 385 kg. Ignoring efficiency gives 192; multiplying by it gives 96; inverting the ratio gives an impossible 10400 kg.

Question 7 · easy

When a steel water trough rusts in neutral, aerated water, what is the main cathodic reaction?

  1. 2H⁺ + 2e⁻ → H2
  2. O2 + 2H2O + 4e⁻ → 4OH⁻
  3. Fe → Fe²⁺ + 2e⁻
  4. Fe²⁺ + 2e⁻ → Fe
Answer and working

B. O2 + 2H2O + 4e⁻ → 4OH⁻

In neutral or alkaline aerated water, dissolved oxygen is reduced to hydroxide at the cathode. Fe → Fe²⁺ + 2e⁻ is the anodic reaction; hydrogen evolution dominates in acid solutions; Fe²⁺ reduction would reverse corrosion.

Question 8 · easy

Which statement correctly distinguishes a thermoplastic from a thermoset?

  1. A thermoplastic softens on reheating; a thermoset is cross-linked and does not
  2. A thermoset softens on reheating; a thermoplastic is cross-linked and does not
  3. A thermoplastic is always made by condensation; a thermoset by addition only
  4. A thermoset is always transparent; a thermoplastic is always black or opaque
Answer and working

A. A thermoplastic softens on reheating; a thermoset is cross-linked and does not

Thermoplastics are linear or branched chains held by weak forces and can be re-melted and re-moulded; thermosets cure into a cross-linked network that chars rather than melts. Either type can be made by addition or condensation, and colour has nothing to do with the classification.

Question 9 · medium

Why do greenhouse films and outdoor HDPE pipes contain UV stabilisers or carbon black?

  1. UV stabilisers are added to make the greenhouse film block all photosynthetic light
  2. Ultraviolet light breaks polymer chains, making plastic brittle unless protected
  3. Carbon black is added only to make the plastic conduct static electricity safely to the ground
  4. Ultraviolet light makes polyethylene absorb rainwater and swell until the film or pipe bursts
Answer and working

B. Ultraviolet light breaks polymer chains, making plastic brittle unless protected

UV photons have enough energy to break bonds and start photo-oxidation, so unprotected polyolefins crack and embrittle; hindered-amine stabilisers, UV absorbers and carbon black slow this. A greenhouse film must still transmit photosynthetically active light, so stabilisers are not added to block it.

Question 10 · hard

A solar irrigation system needs a 48 V battery bank. How many nominal 2 V lead–acid cells, or 3.2 V lithium iron phosphate cells, must be in series?

  1. 24 lead–acid cells or 15 LFP cells
  2. 12 lead–acid cells or 24 LFP cells
  3. 48 lead–acid cells or 15 LFP cells
  4. 24 lead–acid cells or 13 LFP cells
Answer and working

A. 24 lead–acid cells or 15 LFP cells

48/2 = 24 lead–acid cells; 48/3.2 = 15 LFP cells. Thirteen cells assumes 3.7 V per cell (a different lithium chemistry); 48 cells uses 1 V per cell.

A study plan for Engineering Physics & Chemistry in CUET-UG for B.Tech Agricultural Engineering

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 89 questions): Waves and optics (15, 17%); Calorific value of fuels (13, 15%); Polymers and plastics used in agriculture (13, 15%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Semiconductor physics basics (13, 15%); Electrochemistry and batteries (12, 13%); Water chemistry: hardness, pH and treatment (12, 13%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Fuels and combustion chemistry (9, 10%); Corrosion and its control (2, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Semiconductor physics basics (5 hard of 13), Water chemistry: hardness, pH and treatment (4 hard of 12), Fuels and combustion chemistry (3 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Corrosion and its control (2 easy of 2); Water chemistry: hardness, pH and treatment (5 easy of 12).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — CUET-UG for B.Tech Agricultural Engineering Engineering Physics & Chemistry

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.