LAISHA
Open Laisha

Agricultural and Biosystems Engineers Licensure Examination Strength of Materials: practice questions

Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC

Original practice questions written to the published syllabus · not past papers
10worked here, free
34written to this exam in this subject
12syllabus units

About Agricultural and Biosystems Engineers Licensure Examination

Agricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.

Source: prc.gov.ph.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Strength of Materials in Agricultural and Biosystems Engineers Licensure Examination

How members carry load: stress, strain, bending, torsion, deflection and buckling, used in machine and structure design.

Our 34 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 7 easy, 21 medium, 6 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.

Question 1 · easy

A 50 mm wide × 150 mm deep timber purlin, placed on edge, carries a bending moment of 3 kN·m. The maximum bending stress is:

  1. 48.0 MPa
  2. 32.0 MPa
  3. 16.0 MPa
  4. 1.6 MPa
Answer and working

C. 16.0 MPa

Z = bd²/6 = 50 × 150²/6 = 187,500 mm³; σ = 3 × 10⁶/187,500 = 16.0 MPa. Laid flat, Z = 150 × 50²/6 and the stress triples to 48.0 MPa. Using bd²/12 as Z doubles the answer. Using bd²/12 as Z gives 32.0 MPa, and converting 3 kN·m with 10⁵ instead of 10⁶ gives 1.6 MPa.

Question 2 · medium

A simply supported steel beam of 4 m span (E = 200 GPa, I = 20 × 10⁶ mm⁴) carries a uniformly distributed load of 5 kN/m. The midspan deflection is closest to:

  1. 40.0 mm
  2. 6.67 mm
  3. 0.417 mm
  4. 4.17 mm
Answer and working

D. 4.17 mm

δ = 5wL⁴/(384EI) with w = 5 N/mm: 5 × 5 × 4000⁴/(384 × 200,000 × 20 × 10⁶) = 4.17 mm. wL⁴/(8EI) is the cantilever result; wL⁴/(48EI) mixes up the point-load constant. wL⁴/(8EI) = 40.0 mm, wL⁴/(48EI) = 6.67 mm, and 0.417 mm is a decimal slip.

Question 3 · medium

A simply supported steel lifting beam of span 3 m (E = 200 GPa, I = 8 × 10⁶ mm⁴) carries 6 kN at midspan. The central deflection is closest to:

  1. 2.11 mm
  2. 33.8 mm
  3. 1.318 mm
  4. 0.0021 mm
Answer and working

A. 2.11 mm

δ = WL³/(48EI) = 6000 × 3000³/(48 × 200,000 × 8 × 10⁶) = 2.11 mm. WL²/(16EI) is the end slope in radians, not a deflection. WL³/(3EI) = 33.8 mm is the cantilever result, 5WL³/(384EI) = 1.318 mm borrows the uniform-load constant, and 0.0021 mm is the answer in metres.

Question 4 · hard

A steel pipe post of a poly-house frame (outer diameter 60 mm, inner 50 mm, E = 200 GPa) is 3 m long and pinned at both ends. Its Euler critical load is closest to:

  1. 18.1 kN
  2. 289.0 kN
  3. 72.2 kN
  4. 139.5 kN
Answer and working

C. 72.2 kN

I = π(60⁴ − 50⁴)/64 = 329,376 mm⁴; P_cr = π²EI/L² = π² × 200,000 × 329,376/3000² = 72.2 kN. A quarter of this is the fixed–free value; ignoring the bore overestimates. The fixed–free value is 18.1 kN, fixed–fixed gives 289.0 kN, and a solid 60 mm section gives 139.5 kN.

Question 5 · hard

A mild-steel solid round column, 50 mm in diameter and 2 m long, is pinned at both ends. Using Rankine's formula with σ_c = 320 MPa and a = 1/7500, the crippling load is closest to:

  1. 628.3 kN
  2. 151.4 kN
  3. 615.2 kN
  4. 142.4 kN
Answer and working

D. 142.4 kN

A = 1963.5 mm², k = d/4 = 12.5 mm, L/k = 160. P = 320 × 1963.5/(1 + 160²/7500) = 142.4 kN. The crushing load σ_cA = 628.3 kN ignores buckling; Euler alone gives 151.4 kN; forgetting to square the slenderness ratio overestimates the load. Forgetting to square L/k gives 615.2 kN.

Question 6 · hard

A thin steel cylinder of 600 mm diameter and 6 mm wall (E = 200 GPa, ν = 0.3) is pressurised to 1 MPa. The increase in its diameter is closest to:

  1. 0.128 mm
  2. 0.150 mm
  3. 0.0300 mm
  4. 0.172 mm
Answer and working

A. 0.128 mm

ε_h = (σ_h − νσ_l)/E = (pD/4tE)(2 − ν) = (600/(4 × 6 × 200,000)) × 1.7 = 2.125e-04; Δd = ε_h × D = 0.128 mm. Ignoring Poisson's effect gives 0.150 mm; (1 − 2ν) is the longitudinal strain factor. Using (2 + ν) gives 0.172 mm, and the (1 − 2ν) factor gives 0.0300 mm.

Question 7 · medium

At a point in a loaded bracket, σ_x = 60 MPa, σ_y = 20 MPa and τ_xy = 15 MPa. The maximum in-plane shear stress is:

  1. 15 MPa
  2. 20 MPa
  3. 25 MPa
  4. 50 MPa
Answer and working

C. 25 MPa

τ_max = radius of Mohr's circle = √[((60 − 20)/2)² + 15²] = √(400 + 225) = 25 MPa. Taking only (σ_x − σ_y)/2 = 20 MPa ignores the applied shear. 50 MPa is the diameter of Mohr's circle, not the radius.

Question 8 · hard

A short 200 mm × 300 mm concrete pedestal for a grain dryer carries 200 kN applied 40 mm off-centre along the 300 mm side. The maximum and minimum compressive stresses are:

  1. 3.33 and 3.33 MPa
  2. 7.33 and -0.67 MPa
  3. 3.78 and 2.89 MPa
  4. 6.00 and 0.67 MPa
Answer and working

D. 6.00 and 0.67 MPa

σ = P/A ± Pe/Z with Z = 200 × 300²/6 about the axis parallel to the 200 mm side: P/A = 3.333 MPa, 6e/b = 0.8, so σ = 3.333(1 ± 0.8) = 6.00 and 0.67 MPa. Using the 200 mm side for b puts e beyond the core and predicts tension (a negative value). 3.33 and 3.33 MPa ignore the eccentricity, and 3.78 and 2.89 MPa drop the 6 in 6e/b.

Question 9 · medium

A cultivator shank has a cross-section of area 1000 mm² and section modulus 25,000 mm³. At its critical section it carries an axial tension of 20 kN and a bending moment of 1.2 kN·m. The maximum normal stress is:

  1. 48 MPa
  2. 68 MPa
  3. 28 MPa
  4. 52.0 MPa
Answer and working

B. 68 MPa

σ = P/A + M/Z = 20 + 48 = 68 MPa on the tension face; the other face has 48 − 20 = 28 MPa compression. Normal stresses on the same plane add algebraically; combining them as a vector square root is wrong. 52.0 MPa is √(20² + 48²).

Question 10 · medium

A ductile steel has a tensile yield stress of 250 MPa. According to the distortion energy (von Mises) theory, its yield stress in pure shear is closest to:

  1. 125 MPa
  2. 250 MPa
  3. 177 MPa
  4. 144 MPa
Answer and working

D. 144 MPa

Von Mises: τ_y = σ_y/√3 = 144 MPa. Tresca gives 125 MPa, about 13% lower; the two theories differ most in pure shear. 177 MPa divides by √2 instead of √3.

A study plan for Strength of Materials in Agricultural and Biosystems Engineers Licensure Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 34 questions): Stress, strain and Hooke's law (5, 15%); Thin cylinders and spheres (5, 15%); Combined stresses and Mohr's circle (4, 12%); Deflection of beams (4, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Bending and shear stresses in beams (3, 9%); Columns: Euler and Rankine formulas (3, 9%); Shear force and bending moment diagrams (3, 9%); Thermal stresses (3, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Elastic constants and their relations (1, 3%); Strain energy (1, 3%); Theories of failure (1, 3%); Torsion of circular shafts (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Strain energy (1 hard of 1), Columns: Euler and Rankine formulas (2 hard of 3), Thermal stresses (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Thermal stresses (2 easy of 3); Thin cylinders and spheres (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Agricultural and Biosystems Engineers Licensure Examination Strength of Materials

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.