Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC
Original practice questions written to the published syllabus · not past papersAgricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.
Source: prc.gov.ph.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Where the energy for farm work comes from, how much is available, and how mechanisation is measured.
Our 44 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 6 easy, 22 medium, 16 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.
During a draught-animal performance trial, which set of observations tells the operator that the animals are fatigued and should be rested?
A. Rising respiration rate, body temperature and heart rate, with frothing at the mouth
Physiological signs of fatigue are rising respiration rate, body temperature and heart rate, frothing, reluctance to move and lying down. Steady pull and normal physiology indicate the animals are coping.
A PTO dynamometer records a torque of 400 N·m at 540 rpm. What is the PTO power?
B. 22.6 kW
P = 2πNT/60 = 2π × 540 × 400 / 60 = 22,619 W = 22.6 kW. Omitting 2π/60 gives 216.0 kW; omitting 2π gives 3.6 kW; omitting /60 gives 1,357 kW.
A three-phase induction motor draws 12 A at 415 V line voltage and 0.85 power factor. Its efficiency is 88%. What is its shaft output?
A. 6.45 kW
Input = √3 × 415 × 12 × 0.85 = 7,332 W; output = 0.88 × 7,332 = 6,452 W ≈ 6.45 kW. Leaving out √3 gives 3.73 kW; 7.33 kW is the input; dividing by efficiency gives 8.33 kW.
A 4-pole induction motor runs on a 50 Hz supply with 4% slip at full load. What is its rotor speed?
B. 1440 rpm
Ns = 120f/p = 120 × 50/4 = 1500 rpm; N = Ns(1 − s) = 1500 × 0.96 = 1440 rpm. 1500 rpm is synchronous speed; 2880 rpm uses pole pairs instead of poles; adding slip gives 1560 rpm.
A 300 W crystalline silicon module has a power temperature coefficient of −0.4%/°C. Estimate its output at 1000 W/m² when the cell temperature is 55 °C.
D. 264 W
Rise above STC = 55 − 25 = 30 °C; loss = 30 × 0.4% = 12%; P = 300 × 0.88 = 264 W. Using 55 °C instead of the rise gives 234 W; adding the loss gives 336 W; 36 W is the loss, not the output.
A farmer wants to run an unmodified diesel pump set on biogas. What is the realistic arrangement?
C. Dual-fuel operation, with a small pilot injection of diesel to ignite the gas
Methane has high auto-ignition resistance and will not ignite by compression alone in a diesel engine, so a pilot diesel injection is used; this saves much, but not all, of the diesel. Spark-ignition engines can run on biogas alone.
A farm burns 5 t of crop residue (calorific value 15 MJ/kg) in a furnace with 70% efficiency to supply heat for a grain dryer. How much useful heat is delivered?
C. 52.5 GJ
Fuel energy = 5000 × 15 = 75,000 MJ = 75 GJ; useful = 0.70 × 75 = 52.5 GJ (= 14,583 kWh). Ignoring efficiency gives 75 GJ; 52,500 is the answer in MJ labelled GJ; dividing by efficiency gives 107.1 GJ.
Ploughing 60 ha requires 3 tractor-hours per hectare. It must be done in 10 working days of 8 hours. What is the minimum number of tractors?
C. 3
Needed = 60 × 3 = 180 tractor-hours; available per tractor = 10 × 8 = 80 h; 180/80 = 2.25 → round up to 3. Rounding down to 2 leaves 20 h of work undone in the window. 1 forgets the 3 tractor-hours per hectare (60/80 = 0.75); 23 divides by one 8-hour day only (180/8 = 22.5).
Custom hiring centres (machinery banks) mainly raise the farm power effectively available to smallholders by:
C. Letting many farmers use machines they could not justify owning, when they need them
Hiring spreads fixed costs over more farms and hours, improving access and timeliness without each farmer buying a machine. It does not change machine ratings.
Two reports give very different 'levels of mechanisation' for the same state. What should you check first?
D. The definition used (power share, operation-wise area, energy share or stock) and the area and data year
There is no single agreed index: power-based, operation-based, energy-based and stock-based measures can differ widely. Compare like with like on definition, area basis and year before judging.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.