LAISHA
Open Laisha

Agricultural and Biosystems Engineers Licensure Examination Theory of Machines: practice questions

Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC

Original practice questions written to the published syllabus · not past papers
10worked here, free
25written to this exam in this subject
10syllabus units

About Agricultural and Biosystems Engineers Licensure Examination

Agricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.

Source: prc.gov.ph.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Theory of Machines in Agricultural and Biosystems Engineers Licensure Examination

Power and machinery allied subjects: pulley and belt sizing, gear and sprocket ratios for farm machinery drives, power transmission and prime-mover matching.

How mechanisms move and transmit power: linkages, cams, gears, belts, flywheels, governors, balancing and vibration.

Our 25 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 9 easy, 13 medium, 3 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.

Question 1 · medium

A translating roller-follower cam on a seed-metering drive shows excessive side thrust and the follower sticks in its guide. Which design change directly reduces the pressure angle without changing the lift or the cam angle for the rise?

  1. Replace the roller with a knife-edge follower
  2. Reduce the cam speed
  3. Shorten the follower guide
  4. Increase the base-circle radius of the cam
Answer and working

D. Increase the base-circle radius of the cam

For a given lift and rise angle, a larger base circle makes the profile less steep and lowers the pressure angle. Speed changes forces from acceleration but not the geometry of the pressure angle. A knife-edge follower wears fast and does not change the angle. Shortening the guide worsens jamming.

Question 2 · easy

A triple-start worm running at 1440 rpm drives a 60-tooth worm wheel. What is the speed of the wheel?

  1. 24 rpm
  2. 480 rpm
  3. 72 rpm
  4. 4320 rpm
Answer and working

C. 72 rpm

Velocity ratio = wheel teeth/number of starts = 60/3 = 20, so wheel speed = 1440/20 = 72 rpm. 24 rpm treats the worm as single-start; 480 rpm divides by the number of starts only. 4320 rpm multiplies by the number of starts.

Question 3 · medium

A tractor with a rear track width of 1.6 m turns so that the midpoint of its rear axle follows a circle of 5 m radius. What is the ratio of the outer rear wheel speed to the inner rear wheel speed?

  1. 1.32
  2. 1.94
  3. 1.19
  4. 1.38
Answer and working

D. 1.38

The outer wheel runs on radius 5 + 0.8 = 5.8 m and the inner on 5 - 0.8 = 4.2 m; speeds are proportional to path radius, so the ratio is 5.8/4.2 = 1.38. Using the full track on each side gives 6.6/3.4 = 1.94. 1.32 adds the full track to the outer radius and keeps the inner at 5 m (6.6/5.0); 1.19 divides 5.0 by 4.2.

Question 4 · medium

Two pulleys of 400 mm and 200 mm diameter are 1.5 m apart and connected by an open flat belt. What is the belt length?

  1. 4.002 m
  2. 3.942 m
  3. 3.949 m
  4. 4.892 m
Answer and working

C. 3.949 m

Open belt: L = π(r1 + r2) + 2x + (r1 - r2)²/x = π(0.3) + 3.0 + (0.1)²/1.5 = 0.9425 + 3.0 + 0.0067 = 3.949 m. The crossed-belt formula with (r1 + r2)² gives 4.002 m; leaving out the last term gives 3.942 m; using diameters in the π term gives 4.892 m.

Question 5 · easy

What is creep in a belt drive?

  1. Small relative sliding caused by the belt stretching more on the tight side than on the slack side
  2. Gross sliding of the whole belt over the pulley when the transmitted load exceeds the friction available
  3. Permanent lengthening of the belt over months of service, which is corrected by re-tensioning
  4. Lateral movement of the belt off the crown of the pulley
Answer and working

A. Small relative sliding caused by the belt stretching more on the tight side than on the slack side

Creep occurs even when the belt is not slipping as a whole: as the belt passes round the driver from the tight to the slack side it contracts, so it moves slightly relative to the pulley surface. The driven speed falls a little. Gross sliding under overload is slip; permanent lengthening is stretch.

Question 6 · medium

A stationary diesel engine driving a pump shows speed swinging repeatedly above and below the set speed although the load is steady. Which condition most likely explains this?

  1. Governor instability caused by too large a flywheel
  2. An isochronous governor that has too much friction to move
  3. Excessive speed droop in the governor setting
  4. Hunting, caused by a governor that is too sensitive or insufficiently damped
Answer and working

D. Hunting, caused by a governor that is too sensitive or insufficiently damped

Continuous oscillation about the set speed under steady load is hunting: an over-sensitive governor (close to isochronous) overcorrects the fuel, and the engine and linkage lag behind. Cures are reducing sensitivity, adding damping or adding flywheel inertia. A large flywheel slows speed changes and reduces hunting; excessive droop gives a steady speed fall with load, not oscillation.

Question 7 · easy

Why is a variable-speed (all-speed) governor usual on farm tractors, whereas many road vehicles use a minimum-maximum governor?

  1. All-speed governors are cheaper to make
  2. A tractor must hold a set engine and PTO speed as field load varies; a road driver sets speed directly with the pedal
  3. Min-max governors cannot be fitted to diesel engines
  4. Tractor engines run at much higher rated speeds than road-vehicle engines, so they need an all-speed governor to prevent overspeed
Answer and working

B. A tractor must hold a set engine and PTO speed as field load varies; a road driver sets speed directly with the pedal

With an all-speed governor the hand throttle sets a speed and the governor adjusts fuel to hold it at any load, which keeps PTO-driven machines at their rated speed. A min-max governor controls only idle and maximum speed; in between the driver sets fuel directly. Cost and engine speed are not the reason; min-max governors are common on diesel road vehicles.

Question 8 · medium

A Prony brake on an engine shaft running at 1200 rpm has an arm 0.8 m long carrying a net load of 150 N at balance. What brake power is the engine developing?

  1. 144.0 kW
  2. 7.54 kW
  3. 15.08 kW
  4. 18.85 kW
Answer and working

C. 15.08 kW

Torque T = WL = 150 x 0.8 = 120 N m. P = 2πNT/60 = 2π x 1200 x 120/60 = 15080 W = 15.08 kW. Omitting 2π/60 gives 144.0 kW; forgetting the arm length gives 18.85 kW. 7.54 kW is half the correct value.

Question 9 · medium

A power tiller's centrifugal clutch has shoes of 0.5 kg each with their centres of mass at 100 mm radius, held back by springs of 150 N per shoe (the shoe travel to the drum is negligible). At what engine speed does the clutch begin to engage?

  1. 523 rpm
  2. 55 rpm
  3. 16.5 rpm
  4. 740 rpm
Answer and working

A. 523 rpm

Engagement starts when mω²r = S: ω = √(150/(0.5 x 0.1)) = 54.77 rad/s, N = 523 rpm. 55 is ω in rad/s mislabelled as rpm. Setting the engagement speed above idle lets the engine idle without driving the tiller. 16.5 rpm puts the radius in millimetres; 740 rpm uses half the shoe mass.

Question 10 · medium

A tractor's single-plate dry clutch (both sides effective) must transmit 400 N m. The linings have outer and inner radii of 160 mm and 100 mm, and μ = 0.35. Assuming uniform wear, what axial spring force is needed?

  1. 8791 N
  2. 3571 N
  3. 2198 N
  4. 4396 N
Answer and working

D. 4396 N

T = nμW(R1 + R2)/2 gives W = T/(nμ R_mean) = 400/(2 x 0.35 x 0.13) = 4396 N. Using one surface doubles it; using the outer radius instead of the mean gives 3571 N; using R1 + R2 as the radius without halving gives 2198 N.

A study plan for Theory of Machines in Agricultural and Biosystems Engineers Licensure Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (68% of the 25 questions): Belt, rope and chain drives: tension ratio and power (7, 28%); Brakes and dynamometers (4, 16%); Clutches (3, 12%); Differential gear (3, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Gears and gear trains: simple, compound and epicyclic (2, 8%); Governors (2, 8%); Balancing of rotating and reciprocating masses (1, 4%); Cams and followers (1, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Flywheels and turning-moment diagrams (1, 4%); Free and forced vibrations and critical speed (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Flywheels and turning-moment diagrams (1 hard of 1), Free and forced vibrations and critical speed (1 hard of 1), Gears and gear trains: simple, compound and epicyclic (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Brakes and dynamometers (2 easy of 4); Gears and gear trains: simple, compound and epicyclic (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Agricultural and Biosystems Engineers Licensure Examination Theory of Machines

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.