Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC
Original practice questions written to the published syllabus · not past papersAgricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.
Source: prc.gov.ph.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Machinery fabrication within the power, energy and machinery subject: materials and their designations, welding and joint strength, machine-shop calculations, sheet-metal development and fabrication practice, solved with a non-programmable calculator.
How farm machines are made: joining, casting, machining, heat treatment and measurement, up to building a prototype.
Our 74 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 36 easy, 31 medium, 7 hard, across 12 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.
A 50 mm diameter shaft is turned at 300 rev/min. What is the cutting speed?
C. 47.1 m/min
V = πDN/1000 = π × 50 × 300 / 1000 = 47.1 m/min. 15.0 omits π; 4712 takes the diameter in centimetres and leaves out the conversion to metres (π × 5 × 300; dropping the 1000 alone would give 47 124); 94.2 uses the diameter as a radius in 2πr.
A taper runs from 50 mm to 40 mm diameter over 100 mm length. To what angle is the compound rest swivelled?
A. 2.86°
Half-angle α = tan⁻¹[(D − d)/2L] = tan⁻¹(10/200) = 2.86°. 5.71° is the included angle approximation (forgot the 2); 11.31° uses (D − d)/(L/2); 1.43° halves the half-angle again.
On a centre lathe, why is the lead screw kept for thread cutting and not used for ordinary turning feeds?
A. To preserve its accuracy, since wear from routine feeding would spoil cut threads
The lead screw's pitch accuracy determines the accuracy of the threads it cuts, so ordinary feeds are taken from the feed rod to save it from wear. It does move the carriage (through the half nut) and can rotate at any geared speed.
A lathe has a lead screw of 6 mm pitch. A thread of 1.5 mm pitch is to be cut with simple change gears. Which driver/driven pair gives the right ratio?
B. 20-tooth driver, 80-tooth driven
Driver/driven = pitch to be cut / lead-screw pitch = 1.5/6 = 1/4, so 20/80. 80/20 gives 24 mm pitch; 30/45 and 40/60 both give 2/3, a 4 mm pitch.
What spindle speed gives a cutting speed of 24 m/min with a 12 mm drill?
B. 637 rev/min
N = 1000V/(πD) = 1000 × 24/(π × 12) = 637 rev/min. 2000 omits π; 6.37 omits the 1000; 318 doubles the diameter, as if 12 mm were the radius.
A shaper is to machine a flat surface 150 mm wide with a cross feed of 0.5 mm per stroke at 30 strokes per minute. How long will it take?
D. 10 min
Strokes needed = 150/0.5 = 300; time = 300/30 = 10 min. 5 min and 20 min halve or double; 300 min confuses the number of strokes with minutes.
What is the bend allowance for a 90° bend in 2 mm sheet with an inside radius of 5 mm, taking the neutral-axis factor k as 0.33?
D. 8.89 mm
BA = θ(R + kt) = (π/2)(5 + 0.33 × 2) = 8.89 mm. 9.42 mm puts the neutral axis at mid-thickness (k = 0.5); 7.85 mm uses the inside radius alone; 11.0 mm uses the outside radius.
A drawing for a sheet-metal grain-bin panel states only '16 gauge'. Why should the thickness be given in millimetres instead?
A. Gauge numbers differ between countries and between steel and non-ferrous sheet
Several gauge systems exist, and the same number gives different thicknesses for steel, galvanised steel and aluminium and in different countries, so the thickness is stated in mm. Gauges are used for sheet as well as wire, and a gauge number is a thickness, not a width.
What does the number in the structural-steel designation S275 (EN 10025) refer to?
B. Minimum yield strength of 275 MPa
Structural steels in EN 10025 are named by minimum yield strength in MPa for the thinnest thickness range. The Indian E250/E350 grades follow the same idea. Tensile strength, hardness and carbon are not what the number gives.
Which international standard series sets general safety requirements for agricultural machinery, such as guarding of moving parts?
B. ISO 4254
ISO 4254 covers the safety of agricultural machinery (part 1 is general requirements). ISO 286 covers limits and fits, ISO 525 bonded abrasive products, and ISO 3650 gauge blocks.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.