LAISHA
Open Laisha

ASRB NET Workshop Technology & Manufacturing: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
125written to this exam in this subject
12syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Workshop Technology & Manufacturing in ASRB NET

Manufacturing as listed in the discipline: process selection, materials for soil-engaging parts, heat treatment, welding and its testing, machining calculations (cutting speed, time, indexing), and fabrication of machinery.

How farm machines are made: joining, casting, machining, heat treatment and measurement, up to building a prototype.

Our 125 ASRB NET questions in this subject: 37 easy, 57 medium, 31 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · easy

Which oxy-acetylene flame is normally used for welding or braze welding brass?

  1. Neutral flame
  2. Carburising flame
  3. Reducing flame with a long feather
  4. Oxidising flame
Answer and working

D. Oxidising flame

Brass contains zinc, which boils off and causes porosity; a slightly oxidising flame forms an oxide film that limits zinc fuming. A neutral flame suits steel. Carburising and reducing flames (the same thing, with excess acetylene) would worsen zinc loss.

Question 2 · hard

Using the IIW formula, what is the carbon equivalent of a steel with 0.45% C, 0.75% Mn and negligible other alloying elements?

  1. 0.450
  2. 1.200
  3. 0.700
  4. 0.575
Answer and working

D. 0.575

CE = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15 = 0.45 + 0.75/6 = 0.45 + 0.125 = 0.575. 0.450 ignores manganese; 1.200 adds manganese at full weight; 0.700 divides manganese by 3. A value this high normally calls for preheat and low-hydrogen practice.

Question 3 · hard

Why is the sprue of a gating system tapered, with its narrow end at the bottom?

  1. A narrow bottom slows the metal so it enters the runner gently and cannot erode the mould
  2. The taper lets the pattern for the sprue be drawn out of the mould without breaking sand
  3. The falling stream speeds up, so a narrowing sprue keeps it full and stops air being drawn in
  4. Metal shrinks as it cools in the sprue, so the taper matches the shrinkage of the column
Answer and working

C. The falling stream speeds up, so a narrowing sprue keeps it full and stops air being drawn in

Velocity rises as √(2gh) down the sprue; by continuity the area must fall or the stream separates from the walls, creating low pressure that aspirates air and sand. Choking the flow rate is done by the gating ratio, not by slowing in the sprue; draft and shrinkage are not the reason.

Question 4 · easy

Which moulding-sand property allows steam and gases to escape from the mould when hot metal is poured?

  1. Refractoriness
  2. Collapsibility
  3. Green strength
  4. Permeability
Answer and working

D. Permeability

Permeability is the ability of the sand mass to pass gas; low permeability causes blowholes. Refractoriness resists high temperature, collapsibility lets the casting contract and the sand be knocked out, and green strength holds the moist mould together.

Question 5 · hard

For a tool–work pair, Taylor's equation is VT^0.25 = 300 (V in m/min, T in min). What tool life is expected at 150 m/min?

  1. 2 min
  2. 4 min
  3. 1.19 min
  4. 16 min
Answer and working

D. 16 min

T = (C/V)^(1/n) = (300/150)^4 = 2⁴ = 16 min. 2 min treats life as proportional to the speed ratio; 4 min squares instead of raising to the fourth power; 1.19 min takes the 0.25 power instead of the 4th.

Question 6 · hard

A shaper has a stroke of 200 mm and makes 30 cutting strokes per minute. The return stroke takes half the time of the cutting stroke. What is the average cutting speed?

  1. 9 m/min
  2. 6 m/min
  3. 12 m/min
  4. 18 m/min
Answer and working

A. 9 m/min

V = LN(1 + m)/1000 with m = return time / cutting time = 0.5: V = 200 × 30 × 1.5/1000 = 9 m/min. 6 m/min ignores the quick return; 12 m/min uses a 1:1 ratio; 18 m/min uses (1 + 1/m).

Question 7 · hard

A part is located on two accurately bored holes using two pins. Why is one of the pins made as a diamond (relieved) pin?

  1. It is harder than a round pin and so resists wear from repeated loading
  2. It centres the part more precisely than a round pin in the same hole
  3. It allows for centre-distance tolerance while still stopping rotation
  4. It lets the part be loaded either way up so foolproofing is not needed
Answer and working

C. It allows for centre-distance tolerance while still stopping rotation

Two full round pins would jam if the hole spacing varies within tolerance. The diamond pin is relieved along the line joining the holes, so it only stops rotation about the round pin. It is not about hardness, and foolproofing is a separate design requirement.

Question 8 · medium

A forged high-carbon steel ploughshare has been hardened by quenching. What should follow before it is used in stony soil?

  1. Normalising in still air to raise its hardness further for wear
  2. Full annealing in the furnace to make the edge as hard as possible
  3. Tempering at a low to moderate temperature to restore toughness
  4. No further treatment, since as-quenched steel is at its toughest
Answer and working

C. Tempering at a low to moderate temperature to restore toughness

As-quenched martensite is very hard but brittle and can shatter on stones; tempering trades a little hardness for toughness. Normalising and annealing would soften the share and lose the hardening, and as-quenched steel is at its least tough.

Question 9 · easy

A 2 m length of 50 mm × 10 mm mild steel flat bar is needed for a prototype. Taking the density of steel as 7850 kg/m³, what is its mass?

  1. 78.5 kg
  2. 0.785 kg
  3. 3.93 kg
  4. 7.85 kg
Answer and working

D. 7.85 kg

Volume = 0.05 × 0.01 × 2 = 0.001 m³; mass = 7.85 kg. 78.5 and 0.785 kg are decimal slips; 3.93 kg uses 1 m.

Question 10 · medium

Which of these belongs in the bill of materials for a prototype seed drill?

  1. Each part's material specification, stock size, quantity and make-or-buy status
  2. The field-test results for draft, field capacity and seed spacing uniformity
  3. The cost of fuel for the tractor that will pull the drill during testing
  4. The names of the operators who will weld, paint and assemble the frame
Answer and working

A. Each part's material specification, stock size, quantity and make-or-buy status

A bill of materials lists every part with its material, stock size, quantity and whether it is made or bought; it drives purchasing, cutting lists and costing. Test results, operating costs and staffing belong in other documents.

A study plan for Workshop Technology & Manufacturing in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (38% of the 125 questions): Drilling, milling and shaping (13, 10%); Lathe operations (13, 10%); Casting processes (11, 9%); Metrology and measurement in the workshop (11, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: MIG and TIG welding and testing of welded joints (11, 9%); Fitting, carpentry and smithy (10, 8%); Jigs, fixtures and gauges (10, 8%); Prototype fabrication (10, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Arc and gas welding (9, 7%); Heat treatment of steels (9, 7%); Press working of sheet metal (9, 7%); Specification of engineering materials (9, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: MIG and TIG welding and testing of welded joints (5 hard of 11), Drilling, milling and shaping (5 hard of 13), Press working of sheet metal (3 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Specification of engineering materials (5 easy of 9); Heat treatment of steels (4 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Workshop Technology & Manufacturing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.