LAISHA
Open Laisha

ASRB NET Soil Science for Engineers: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
57written to this exam in this subject
9syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Soil Science for Engineers in ASRB NET

Same ground as AICE at a similar depth, with more recall of definitions, classification systems and measurement methods.

The soil an engineer tills, irrigates, drains and builds on: its physical, water and chemical properties.

Our 57 ASRB NET questions in this subject: 3 easy, 37 medium, 17 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

Two soils have the same mineralogy. Soil X has a higher organic matter content than soil Y. Compared with soil Y, soil X will most likely have:

  1. Higher particle density but a lower bulk density
  2. Higher particle density and higher bulk density
  3. The same particle density but a higher bulk density
  4. Lower particle density and lower bulk density
Answer and working

D. Lower particle density and lower bulk density

Organic matter has a particle density of about 1.2–1.5 g/cm³, so it lowers the soil's average particle density; it also promotes aggregation and pore space, lowering bulk density. Neither density rises with more organic matter.

Question 2 · hard

The least limiting water range (LLWR) narrows the classical available water range by taking into account:

  1. Salinity at the wet end and hygroscopic water at the dry end of the range
  2. Hysteresis at the wet end and the osmotic potential of root cells at the dry end
  3. Aeration at the wet end and soil penetration resistance at the dry end
  4. Crop rooting depth at the wet end and evaporative demand at the dry end
Answer and working

C. Aeration at the wet end and soil penetration resistance at the dry end

LLWR (da Silva, Kay and Perfect, 1994) uses as the upper limit the wetter of field capacity or the water content at which air-filled porosity falls to a critical value (often 10%), and as the lower limit the drier of wilting point or the water content at which penetration resistance reaches a critical value (often about 2 MPa). It shrinks with compaction; the other pairs are not its definition.

Question 3 · medium

Hydraulic conductivity K and intrinsic permeability k are related by K = kρg/μ. If the same soil is tested with water at 30 °C instead of 10 °C, K will:

  1. Decrease, because warm water dissolves air that then blocks the pores
  2. Decrease, because the density of water decreases as it warms
  3. Increase, because the viscosity of water decreases as it warms
  4. Stay the same, because K depends only on the pore geometry of the soil
Answer and working

C. Increase, because the viscosity of water decreases as it warms

Water's viscosity falls by about 40% between 10 and 30 °C (1.31 to 0.80 mPa s) while its density changes by less than 1%, so K rises; this is why K is corrected to a standard temperature. k depends only on pore geometry, but K includes the fluid properties. Warm water holds less dissolved air, not more.

Question 4 · medium

As a soil dries from saturation, its unsaturated hydraulic conductivity:

  1. Falls steeply, often by several orders of magnitude, as the larger pores empty
  2. Stays equal to the saturated value until the soil reaches the wilting point
  3. Rises steadily, because the matric suction gradients become much steeper
  4. Falls, usually in direct proportion to the volumetric water content of the soil
Answer and working

A. Falls steeply, often by several orders of magnitude, as the larger pores empty

Flow capacity depends roughly on the fourth power of pore radius, so emptying the large pores first cuts K(θ) drastically; it can fall by orders of magnitude between saturation and field capacity. Steeper gradients can raise flux but not conductivity; K is not constant to wilting point, and the decline is strongly non-linear.

Question 5 · medium

For designing subsurface drain spacing, which field method is standard for measuring saturated hydraulic conductivity below a shallow water table?

  1. Ring infiltrometer
  2. Falling-head permeameter on a small core
  3. Auger-hole method
  4. Tension disc infiltrometer
Answer and working

C. Auger-hole method

The auger-hole method measures the rate of rise of water in a hole bored below the water table and gives K of a large soil volume at the depth that matters for drains. Ring and tension infiltrometers measure surface infiltration above the water table, and small cores in a laboratory permeameter often miss the macropores that dominate field flow.

Question 6 · medium

Why is the electrical conductivity of the saturated paste extract (ECe) used as the reference measure of soil salinity rather than EC of a 1:5 extract?

  1. The saturated paste extract dissolves all gypsum and lime, giving the total salt in the soil
  2. The 1:5 extract cannot be measured with a standard conductivity meter in the laboratory
  3. ECe is always exactly five times the EC of the 1:5 extract in every kind of soil
  4. Saturation water content tracks field water content fairly evenly across textures
Answer and working

D. Saturation water content tracks field water content fairly evenly across textures

The saturation percentage is roughly twice field capacity in many soils, so ECe tracks the salinity roots experience and crop tolerance data are tabulated against it. Wider ratios dilute the solution and dissolve more sparingly soluble salts, so conversions to ECe are soil-specific, not a fixed factor; a 1:5 extract is easy to measure.

Question 7 · hard

Why does a soil's lime requirement depend on its CEC and organic matter, and not just on its measured pH?

  1. Reserve acidity on the colloids far exceeds active acidity and buffers pH change
  2. Organic matter reacts with lime to form insoluble salts, so more is needed to reach the same pH
  3. The pH electrode misreads in high-CEC soils, so readings need correcting
  4. High-CEC soils contain calcium carbonate that dissolves and neutralises part of the applied lime
Answer and working

A. Reserve acidity on the colloids far exceeds active acidity and buffers pH change

Most soil acidity is held on the exchange complex and pH-dependent sites (reserve acidity), far exceeding the H⁺ in solution; a soil with more clay and humus has more reserve acidity and needs more lime for the same pH change. Electrode error, carbonate in acid soils and insoluble organic salts are not the reason.

Question 8 · hard

Under the USSL Handbook 60 convention, a soil is classed as sodic when its ESP exceeds 15. Which alternative criterion is used in Australian practice?

  1. ESP above 6
  2. ESP above 25
  3. SAR above 30
  4. ECe above 15 dS/m
Answer and working

A. ESP above 6

Australian classification (following Northcote and Skene) treats soils with ESP above 6 as sodic, recognising that dispersion problems begin well below ESP 15 in low-salinity conditions; some authorities use SAR 13 in place of ESP 15. ESP 25, SAR 30 and ECe 15 are not the standard alternative thresholds.

Question 9 · hard

In laboratory determination of ESP, exchangeable sodium is obtained by:

  1. Measuring sodium in a 1:5 water extract alone, since all exchangeable sodium is water-soluble
  2. Ammonium acetate-extractable sodium minus the soluble sodium of the saturation extract
  3. Measuring total sodium after digesting the soil in strong acid and subtracting the CEC value
  4. Dividing the SAR of the saturation extract by the cation exchange capacity of the soil sample
Answer and working

B. Ammonium acetate-extractable sodium minus the soluble sodium of the saturation extract

Ammonium acetate extracts both exchangeable and soluble sodium; subtracting soluble sodium (from the saturation extract) leaves exchangeable Na, which is divided by CEC. Exchangeable sodium is not water-soluble, SAR/CEC has no meaning, and acid digestion measures total sodium including that in minerals.

Question 10 · medium

Why is subsurface drainage usually needed when reclaiming a saline soil by leaching in an irrigated area with a shallow water table?

  1. To aerate the soil so that soluble salts oxidise into insoluble compounds in the profile
  2. To raise the water table so that the root zone stays moist during the leaching period
  3. To carry leached salts away and keep the water table below capillary reach
  4. To supply calcium from the drain envelope to replace exchangeable sodium
Answer and working

C. To carry leached salts away and keep the water table below capillary reach

Leaching only works if the salty water can leave the root zone; with a shallow water table it simply raises the table, and capillary rise then brings salts back. Drains do not supply calcium, should lower rather than raise the water table, and salts are not removed by oxidation.

A study plan for Soil Science for Engineers in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 57 questions): Problem soils: saline, sodic and acid (11, 19%); Soil chemistry: pH and electrical conductivity (10, 18%); Soil formation and profile (10, 18%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Bulk density, particle density and porosity (5, 9%); Hydraulic conductivity and Darcy's law (5, 9%); Soil water: field capacity, wilting point and available water (5, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Infiltration (4, 7%); Sodicity: SAR and ESP (4, 7%); Soil texture and structure (3, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Sodicity: SAR and ESP (3 hard of 4), Infiltration (2 hard of 4), Problem soils: saline, sodic and acid (5 hard of 11).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Soil chemistry: pH and electrical conductivity (2 easy of 10); Soil formation and profile (1 easy of 10).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Soil Science for Engineers

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.