LAISHA
Open Laisha

ASRB NET Bio-energy Systems: Design & Applications: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
58written to this exam in this subject
12syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Bio-energy Systems: Design & Applications in ASRB NET

Theory-heavy MCQs across the whole subject: comparison of gasifier types, biogas plant designs and their parts, digestion microbiology, briquetting machines and binding, bio-oil and charcoal, biofuel properties, and energy audit terminology.

Turning crop residues, dung and oils into fuel: briquettes, gasifiers, biogas plants and liquid biofuels, and auditing farm energy.

Our 58 ASRB NET questions in this subject: 25 easy, 32 medium, 1 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

Compared with bituminous coal, typical woody and herbaceous biomass has:

  1. Lower volatile matter, higher fixed carbon and lower oxygen content than coal
  2. Higher sulphur and higher fixed carbon
  3. Similar oxygen content but much higher hydrogen content
  4. Higher volatile matter, lower fixed carbon and higher oxygen content
Answer and working

D. Higher volatile matter, lower fixed carbon and higher oxygen content

Biomass is a young, oxygen-rich fuel: volatile matter is commonly 65–85% on a dry basis and oxygen around 35–45%, so most of its energy is released as volatiles and its heating value is lower than coal. Coal has more fixed carbon, less oxygen and usually more sulphur. That high volatile fraction is why biomass ignites easily and why pyrolysis and gasification are central to biomass conversion.

Question 2 · easy

The value obtained directly from an oxygen bomb calorimeter is:

  1. Gross heating value at constant volume
  2. The net (lower) heating value at constant pressure, as fired
  3. The heating value on a dry ash-free basis
  4. The heating value of the volatile matter only
Answer and working

A. Gross heating value at constant volume

In the bomb, the products cool back to near room temperature and the water formed condenses, so the heat measured includes the latent heat: it is the gross heating value, determined at constant volume. The net value is calculated from it using the hydrogen and moisture content. Conversion to a dry or daf basis is a separate arithmetic step.

Question 3 · easy

The main purpose of briquetting loose agricultural residues is to:

  1. Increase the heating value per kg of dry matter by driving off volatile matter
  2. Reduce the ash content of the residue by squeezing out mineral matter under pressure
  3. Convert cellulose into lignin
  4. Raise bulk and energy density for easier storage, transport and uniform burning
Answer and working

D. Raise bulk and energy density for easier storage, transport and uniform burning

Densification raises density by roughly an order of magnitude, so a truck or store holds far more energy and the fuel burns more steadily. It does not change the heating value per kg of dry matter (apart from small moisture changes), and it cannot remove ash; ash that goes in comes out in the briquette.

Question 4 · easy

The correct sequence of events when a particle of wood burns is:

  1. Char combustion, drying, devolatilisation, flaming combustion
  2. Devolatilisation (pyrolysis), drying, char combustion, flaming combustion
  3. Drying, devolatilisation, flaming, char combustion
  4. Flaming combustion, drying, char combustion, devolatilisation
Answer and working

C. Drying, devolatilisation, flaming, char combustion

Heat first drives off moisture; the dry particle then decomposes into volatiles and char; the volatiles burn in the flame around the particle; the remaining char burns more slowly as a glowing solid once oxygen can reach it. In a large fire these stages overlap in space, but each particle passes through them in this order.

Question 5 · medium

Which reactions in the reduction zone of a gasifier are endothermic?

  1. The combustion reaction C + O2 → CO2 and the water–gas shift reaction
  2. The Boudouard reaction (C + CO2 → 2CO) and the water–gas reaction (C + H2O → CO + H2)
  3. Methanation (C + 2H2 → CH4) and the combustion of hydrogen
  4. Only the partial oxidation C + ½O2 → CO
Answer and working

B. The Boudouard reaction (C + CO2 → 2CO) and the water–gas reaction (C + H2O → CO + H2)

The Boudouard (about +172 kJ/mol) and water–gas (about +131 kJ/mol) reactions absorb heat supplied by the oxidation zone, which is why the reduction zone cools as gas passes through it. Combustion to CO2 and partial oxidation to CO are exothermic; the water–gas shift and methanation are mildly exothermic.

Question 6 · easy

Producer gas from an air-blown biomass gasifier has a lower heating value typically of about:

  1. 20–25 MJ/Nm³
  2. 35–40 MJ/Nm³
  3. 0.4–0.6 MJ/Nm³
  4. 4–6 MJ/Nm³
Answer and working

D. 4–6 MJ/Nm³

Air-blown gas is about half nitrogen, with CO and H2 each around 15–22% and a few percent CH4, giving roughly 4–6 MJ/Nm³. Biogas is about 20–25 MJ/m³ and natural gas about 35–40 MJ/Nm³. Oxygen- or steam-blown gasification gives a richer gas with a higher value. 0.4–0.6 MJ/Nm³ is a factor-of-ten slip.

Question 7 · medium

A compression-ignition engine cannot run on producer gas alone without modification because:

  1. Producer gas will not self-ignite on compression, so a pilot diesel spray is needed
  2. Producer gas contains too much oxygen and would ignite in the intake manifold
  3. Producer gas knocks severely at any compression ratio, so the pistons would fail within hours
  4. Producer gas cannot mix with air
Answer and working

A. Producer gas will not self-ignite on compression, so a pilot diesel spray is needed

The gas–air mixture is inducted and compressed but does not auto-ignite reliably; a small injection of diesel ignites and the flame spreads through the gas–air charge. Removing diesel entirely needs conversion to spark ignition (and usually a lower compression ratio). CO and CH4 are knock-resistant, so knock is not the obstacle.

Question 8 · medium

Before producer gas is admitted to an engine, it is cooled and cleaned mainly to:

  1. Increase its hydrogen content
  2. Convert CO to CO2 so the gas becomes safe to handle in the engine room without ventilation
  3. Raise gas density for more energy per stroke and remove tar and dust that foul valves
  4. Remove nitrogen so the heating value rises to that of natural gas and the engine gains power
Answer and working

C. Raise gas density for more energy per stroke and remove tar and dust that foul valves

Hot gas is less dense, so a cylinder would draw less energy; cooling it restores volumetric energy. Tar condenses on intake valves and sticks them, and dust wears rings and cylinders. Cooling and cleaning trains (cyclone, scrubber or cooler, filters) are therefore as important as the reactor. Nitrogen cannot be removed economically, and CO is the main fuel component, not an impurity.

Question 9 · medium

Alkali-catalysed transesterification is usually run near 60 °C mainly because:

  1. Triglycerides decompose above about 60 °C into free fatty acids and acrolein (spoiling the product)
  2. Just below methanol's boiling point (about 65 °C), giving fast reaction without pressurising
  3. The catalyst is inactive below 60 °C
  4. Glycerol freezes below 60 °C
Answer and working

B. Just below methanol's boiling point (about 65 °C), giving fast reaction without pressurising

Reaction rate rises with temperature, but methanol boils at about 64.7 °C at atmospheric pressure; running just below that keeps it liquid without a pressure vessel or heavy reflux. Supercritical processes run far hotter but at high pressure. The catalyst works at room temperature too, just more slowly.

Question 10 · easy

The two main combustible components of producer gas from air-blown gasification of wood are:

  1. Methane and ethane
  2. Carbon monoxide and hydrogen
  3. Carbon dioxide and nitrogen
  4. Oxygen and hydrogen sulphide
Answer and working

B. Carbon monoxide and hydrogen

CO and H2 together usually make up about 35–40% of the gas and supply most of its energy; methane adds a few percent. Nitrogen (about half the gas) and CO2 are inert diluents. Methane is the main fuel in biogas, not producer gas.

A study plan for Bio-energy Systems: Design & Applications in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (40% of the 58 questions): Biomass characterisation: proximate and ultimate analysis (7, 12%); Anaerobic digestion stages (6, 10%); Bio-ethanol (5, 9%); Biodiesel and transesterification (5, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Biogas plant types: floating drum and fixed dome (5, 9%); Briquetting and pelleting (5, 9%); Gasification: updraft and downdraft gasifiers (5, 9%); Calorific value (4, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Combustion of biomass (4, 7%); Energy audit and energy ratio in agriculture (4, 7%); Producer gas and dual-fuel engines (4, 7%); Pyrolysis (4, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Combustion of biomass (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Biomass characterisation: proximate and ultimate analysis (4 easy of 7); Anaerobic digestion stages (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Bio-energy Systems: Design & Applications

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.