LAISHA
Open Laisha

ASRB NET Post-Harvest Engineering of Cereals, Pulses & Oilseeds: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
54written to this exam in this subject
12syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Post-Harvest Engineering of Cereals, Pulses & Oilseeds in ASRB NET

Post-harvest operations, engineering properties, process equipment design and material handling at PG level, with emphasis on Indian practice: LSU and recirculating dryers, hot-soak parboiling, rubber-roll and disc huskers, dhal milling pretreatments, expellers and solvent plants.

Moisture, drying, parboiling, milling, cleaning, size reduction and conveying of grains, pulses and oilseeds.

Our 54 ASRB NET questions in this subject: 17 easy, 29 medium, 8 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · hard

Using the Henderson equation 1 − RH = exp(−c·T·Mⁿ) with hypothetical constants c = 2.0 × 10⁻⁵ and n = 2 (T in K, M in % dry basis), the EMC at 300 K and 70% RH is closest to

  1. 201% db
  2. 12.4% db
  3. 14.2% db
  4. 7.7% db
Answer and working

C. 14.2% db

Mⁿ = −ln(1 − 0.70)/(c·T) = 1.2040/(0.0060) = 200.7, so M = √200.7 = 14.17% db. Using ln(0.70) instead of ln(0.30) gives 7.7%; forgetting the square root gives 201%; 12.4% is the wet-basis value mislabelled as dry basis.

Question 2 · hard

A rice mill notices head rice yield fell by several points after the dryer operator raised air temperature and ran each batch straight through to 14% moisture. The most likely cause and remedy are

  1. too low final moisture from the meter; recalibrate the meter to read higher
  2. stress fissures from steep moisture gradients; use cooler air and dry in passes with tempering
  3. over-husking in the rubber-roll sheller from worn rolls; widen the roll gap and replace the rolls
  4. insufficient whitening; add a whitening pass
Answer and working

B. stress fissures from steep moisture gradients; use cooler air and dry in passes with tempering

Fast, hot, uninterrupted drying creates moisture gradients that fissure rice kernels, which then break in milling. The husker and whitener were unchanged, so they are not the first suspects.

Question 3 · medium

In a cross-flow column dryer, the grain at the discharge typically shows

  1. a moisture gradient across the column, with grain nearest the air inlet overdried
  2. uniform moisture across the column
  3. rewetting of all the grain by the exhaust air
  4. the wettest grain nearest the hot-air inlet and the driest grain at the exhaust side
Answer and working

A. a moisture gradient across the column, with grain nearest the air inlet overdried

Grain on the inlet side meets the hottest, driest air for the whole residence time. Mixed-flow designs such as the LSU dryer reduce this non-uniformity.

Question 4 · easy

The purifier in a wheat mill

  1. separates the germ by flotation
  2. grades and cleans middlings on an oscillating sieve with an upward air current
  3. bleaches flour
  4. removes stones, mud balls and iron from the wheat on the cleaning floor before conditioning
Answer and working

B. grades and cleans middlings on an oscillating sieve with an upward air current

Air lifts light bran particles off the sieve while endosperm particles are graded by size; purified middlings go to the reduction rolls.

Question 5 · medium

Compared with the break system, the reduction system of a roller flour mill uses

  1. smooth rolls with a smaller speed differential
  2. more deeply corrugated rolls with a larger differential
  3. hammer mills
  4. attrition discs
Answer and working

A. smooth rolls with a smaller speed differential

Reduction rolls gently crush purified middlings to flour; a small differential (roughly 1.25–1.5:1) limits bran shattering and starch damage.

Question 6 · medium

A specific-gravity (gravity) table is most useful for separating

  1. long from short particles
  2. iron from grain
  3. round from flat particles, since round seeds roll down the tilted deck and flat ones slide
  4. same-size particles of different density, such as sound and insect-damaged seed
Answer and working

D. same-size particles of different density, such as sound and insect-damaged seed

Air stratifies the bed and deck vibration moves heavy particles uphill while light ones flow down. Size must be similar, so the feed is sized first.

Question 7 · medium

To remove chaff and dust from grain with an aspirator, the air velocity should be set

  1. above the terminal velocity of the grain
  2. above the terminal velocity of light impurities but below that of the grain
  3. equal to the grain's terminal velocity
  4. below the terminal velocity of the impurities, so that no grain is ever lifted out
Answer and working

B. above the terminal velocity of light impurities but below that of the grain

Only particles whose terminal velocity is below the air velocity are lifted. Too high a velocity carries grain away; too low leaves the chaff.

Question 8 · hard

By Harrington's rules of thumb, lowering seed moisture by 2 percentage points and storage temperature by 10 °C would multiply expected storage life by roughly

  1. 16
  2. 8
  3. 6
  4. 4
Answer and working

A. 16

Moisture: 2 × 2 = 4; temperature: each 5 °C fall doubles life, so 10 °C gives 4; combined 4 × 4 = 16. Adding the factors (4 + 4 = 8) is the common slip. 6 adds the moisture factor to a single temperature doubling (4 + 2).

Question 9 · easy

The usual order of operations in seed processing is

  1. basic cleaning, bagging, drying, treating
  2. treating, drying, pre-cleaning, bagging, upgrading, receiving, then basic cleaning
  3. upgrading, receiving, treating, pre-cleaning
  4. receiving, pre-cleaning, drying, basic cleaning, upgrading, treating, bagging
Answer and working

D. receiving, pre-cleaning, drying, basic cleaning, upgrading, treating, bagging

Seed is pre-cleaned so it dries evenly, cleaned on an air-screen cleaner, upgraded, and treated last so that protectant is not wasted on rejects.

Question 10 · medium

A magnetic seed separator (with iron powder) separates seeds by

  1. their colour
  2. surface texture: iron powder sticks to rough or sticky coats, which a magnet then draws off
  3. their length
  4. their natural magnetic properties, which vary with the iron taken up from the soil by each seed
Answer and working

B. surface texture: iron powder sticks to rough or sticky coats, which a magnet then draws off

Seeds are mixed with fine iron powder and moisture; rough-coated weed seeds hold the powder and are removed by a magnetic drum, while smooth crop seeds do not.

A study plan for Post-Harvest Engineering of Cereals, Pulses & Oilseeds in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 54 questions): Seed processing (8, 15%); Equilibrium moisture content and sorption isotherms (6, 11%); Oil expression and solvent extraction (6, 11%); Pulse milling (6, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Grain dryers: bin, LSU, recirculating, fluidised-bed and solar (5, 9%); Paddy and rice milling: husking, whitening, polishing and yields (5, 9%); Cleaning, grading and screening effectiveness (4, 7%); Parboiling and hydrothermal treatment (4, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Drying theory: constant and falling rate periods (3, 6%); Wheat milling (3, 6%); Conveying: belt, bucket, screw and pneumatic (2, 4%); Moisture content: wet and dry basis (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Drying theory: constant and falling rate periods (2 hard of 3), Cleaning, grading and screening effectiveness (1 hard of 4), Grain dryers: bin, LSU, recirculating, fluidised-bed and solar (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Wheat milling (2 easy of 3); Pulse milling (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Post-Harvest Engineering of Cereals, Pulses & Oilseeds

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.