LAISHA
Open Laisha

ASRB NET Fluid Mechanics & Open Channel Hydraulics: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
35written to this exam in this subject
17syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Fluid Mechanics & Open Channel Hydraulics in ASRB NET

Similar to the ICAR PhD paper: standard results and their conditions across pipe flow, flow measurement and open-channel hydraulics.

Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.

Our 35 ASRB NET questions in this subject: 4 easy, 14 medium, 17 hard, across 17 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · hard

A rectangular pontoon 6 m long and 3 m wide floats in fresh water with a draught of 1.0 m. Its centre of gravity is 1.0 m above the bottom. What is its metacentric height for rolling about the long axis, and is it stable?

  1. 0.25 m, stable
  2. 1.25 m, stable
  3. 0.75 m, stable
  4. -0.50 m, unstable
Answer and working

A. 0.25 m, stable

V = 6 × 3 × 1 = 18 m³; I = Lb³/12 = 6 × 27/12 = 13.5 m⁴; BM = I/V = 0.75 m. B is at half the draught, 0.5 m above the bottom, so BG = 1.0 − 0.5 = 0.5 m. GM = BM − BG = 0.25 m > 0, so stable. Adding BG instead of subtracting gives 1.25 m.

Question 2 · medium

A proposed two-dimensional steady incompressible flow has the velocity component u = 2x in the x-direction. Which y-component makes the flow satisfy continuity (taking v = 0 on y = 0)?

  1. v = 2xy
  2. v = 2y
  3. v = −2y
  4. v = −2x
Answer and working

C. v = −2y

Continuity for 2-D incompressible flow requires ∂u/∂x + ∂v/∂y = 0. ∂u/∂x = 2, so ∂v/∂y = −2 and v = −2y + f(x); with v = 0 on y = 0, f(x) = 0. v = 2y gives a divergence of 4, which is impossible for an incompressible fluid.

Question 3 · hard

Laminar flow of a given discharge passes through a pipe. If the pipe diameter is halved while the discharge and length stay the same, by what factor does the friction head loss change?

  1. It increases 8 times
  2. It increases 32 times
  3. It increases 4 times
  4. It increases 16 times
Answer and working

D. It increases 16 times

Hagen-Poiseuille: h_f = 32μVL/(ρgD²) and V = 4Q/(πD²), so h_f ∝ Q/D⁴. Halving D multiplies h_f by 2⁴ = 16. The factor 32 would follow from the turbulent Darcy form with constant f (h_f ∝ 1/D⁵).

Question 4 · hard

Two reservoirs with a 5 m difference in water level are joined by a 50 m pipe of 100 mm diameter with a sharp-edged entrance (K = 0.5) and exit loss (K = 1.0). The Darcy friction factor is 0.02. What is the discharge?

  1. 22.9 L/s
  2. 24.6 L/s
  3. 12.1 L/s
  4. 24.0 L/s
Answer and working

A. 22.9 L/s

Energy from surface to surface: 5 = (K_ent + K_exit + fL/D)V²/2g = (0.5 + 1.0 + 0.02 × 500)V²/2g = 11.5 V²/2g. V = √(2 × 9.81 × 5/11.5) = 2.92 m/s; Q = 22.9 L/s. Ignoring minor losses gives 24.6 L/s; forgetting the exit loss gives 24.0 L/s; using 4f gives 12.1 L/s.

Question 5 · hard

A total flow of 100 L/s divides between two parallel pipes of equal length and friction factor, 200 mm and 100 mm in diameter. How much flows through the 200 mm pipe?

  1. 80.0 L/s
  2. 66.7 L/s
  3. 85.0 L/s
  4. 97.0 L/s
Answer and working

C. 85.0 L/s

Q₁/Q₂ = (D₁/D₂)^2.5 = 5.66 (equal head loss, h_f ∝ Q²/D⁵). Q₁ = 100 × 5.66/(1 + 5.66) = 85.0 L/s. Splitting in the ratio of areas (4:1) gives 80 L/s; in the ratio of diameters, 66.7 L/s. 97.0 L/s splits in the ratio of D⁵ (32:1) without the square root.

Question 6 · hard

A rectangular channel 4 m wide carries 8 m³/s at a depth of 0.5 m. What is the alternate depth, the depth on the other limb of the specific-energy curve with the same specific energy?

  1. 1.17 m
  2. 0.742 m
  3. 1.32 m
  4. 1.05 m
Answer and working

A. 1.17 m

q = 8/4 = 2 m²/s. E = y + q²/(2gy²) = 0.5 + 4/(19.62 × 0.25) = 1.32 m. Solving y + 0.2039/y² = 1.32 on the subcritical limb gives y ≈ 1.17 m. 0.742 m is the critical depth; 1.05 m is the sequent depth of a hydraulic jump, which conserves momentum, not energy.

Question 7 · hard

A triangular channel with side slopes 1 horizontal to 1 vertical carries 2 m³/s. What is the critical depth?

  1. 0.836 m
  2. 0.742 m
  3. 0.960 m
  4. 1.46 m
Answer and working

C. 0.960 m

The general critical condition is Q²T/(gA³) = 1. For z = 1: A = y², T = 2y, so Q² × 2y/(g y⁶) = 1, y⁵ = 2Q²/g = 0.815, y_c = 0.960 m. Using the rectangular formula (q²/g)^(1/3) with Q gives 0.742 m, which does not apply to a triangle. 0.836 m forgets the factor 2 from T = 2y (y⁵ = Q²/g); 1.46 m takes the area as y²/2.

Question 8 · medium

Subcritical flow in a rectangular channel passes over a smooth, low hump in the bed without choking. Neglecting losses, what happens to the water surface over the hump?

  1. It rises to critical depth whatever the hump height
  2. It drops
  3. It stays level
  4. It rises
Answer and working

B. It drops

The specific energy over the hump is reduced by the hump height. On the subcritical (upper) limb of the E-y curve, lower E means lower depth, and the drop in depth exceeds the hump height, so the surface drops. In supercritical flow the depth, and the surface, would rise.

Question 9 · hard

Water leaves a sluice gate at a depth of 0.35 m with a discharge of 4 m³/s per metre width and forms a hydraulic jump on a horizontal apron. What fraction of the incoming specific energy is dissipated in the jump?

  1. About 3.5 %
  2. About 43 %
  3. About 57 %
  4. About 88 %
Answer and working

C. About 57 %

V₁ = 4/0.35 = 11.4 m/s; Fr₁ = 11.4/√(9.81 × 0.35) = 6.17. y₂ = 0.175[√(1 + 8 × 6.17²) − 1] = 2.88 m. ΔE = (y₂ − y₁)³/(4y₁y₂) = 4.03 m. E₁ = 0.35 + 11.4²/19.62 = 7.01 m, so the loss is 57 % of E₁. 43 % is the fraction retained downstream, not the fraction lost. About 3.5 % comes from forgetting to square Fr₁ (y₂ = 1.07 m); 88 % is (y₂ − y₁)/y₂, a depth ratio, not an energy ratio.

Question 10 · hard

The measured depths before and after a hydraulic jump in a horizontal rectangular channel are 0.3 m and 1.8 m. What discharge per unit width is passing?

  1. 1.99 m²/s
  2. 7.56 m²/s
  3. 2.36 m²/s
  4. 3.34 m²/s
Answer and working

C. 2.36 m²/s

From momentum, q² = g y₁ y₂ (y₁ + y₂)/2 = 9.81 × 0.3 × 1.8 × 2.1/2 = 5.56, so q = 2.36 m²/s. Omitting the /2 gives 3.34 m²/s; treating 1.8 m as a critical depth gives 7.56 m²/s. 1.99 m²/s uses (y₂ − y₁) instead of (y₁ + y₂).

A study plan for Fluid Mechanics & Open Channel Hydraulics in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (57% of the 35 questions): Specific energy and critical depth (5, 14%); Hydraulic jump (4, 11%); Pipes in series and parallel (4, 11%); Dimensional analysis and similitude (3, 9%); Laminar and turbulent flow in pipes (2, 6%); Momentum equation (2, 6%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Most economical channel section (2, 6%); Orifices, mouthpieces and tank emptying (2, 6%); Properties of fluids (2, 6%); Uniform flow in open channels: Manning and Chezy (2, 6%); Bernoulli's equation: venturimeter, orifice meter and pitot tube (1, 3%); Continuity equation (1, 3%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Forces on submerged surfaces and buoyancy (1, 3%); Hazen-Williams equation (1, 3%); Hydrostatics and manometry (1, 3%); Minor losses (1, 3%); Weirs and notches (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Bernoulli's equation: venturimeter, orifice meter and pitot tube (1 hard of 1), Forces on submerged surfaces and buoyancy (1 hard of 1), Hydrostatics and manometry (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Momentum equation (1 easy of 2); Most economical channel section (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Fluid Mechanics & Open Channel Hydraulics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.