LAISHA
Open Laisha

ASRB NET Soil Mechanics: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
36written to this exam in this subject
9syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Soil Mechanics in ASRB NET

Deeper treatment of seepage through and under earth dams (phreatic line, filters, piping), consolidation theory and its assumptions, drained versus undrained analysis, stability cases for earth dams including rapid drawdown, and methods of slices.

Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.

Our 36 ASRB NET questions in this subject: 0 easy, 13 medium, 23 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · hard

A deposit consists of two layers of equal thickness with permeabilities of 1 × 10⁻³ cm/s and 1 × 10⁻⁵ cm/s. What is the ratio of equivalent horizontal to equivalent vertical permeability?

  1. 25.5
  2. 100.0
  3. 1.0
  4. 51.0
Answer and working

A. 25.5

kh = (k1 + k2)/2 = 5.050e-04 cm/s. kv = 2/(1/k1 + 1/k2) = 2/(1000 + 100000) = 1.980e-05 cm/s. kh/kv = 25.5. 100 is simply k1/k2, which is not the ratio of the equivalent values. 51.0 forgets the 2 in the harmonic mean, taking kv = 1/(1/k1 + 1/k2) = 9.90e-06 cm/s.

Question 2 · hard

A clay deposit with its water table at the ground surface has γsat = 19 kN/m³. Drainage lowers the water table by 3 m, and the clay above the new water table then has a unit weight of 18 kN/m³. What is the change in vertical effective stress at 10 m depth (γw = 9.81 kN/m³)?

  1. Increase of 26.4 kPa
  2. Increase of 29.4 kPa
  3. Decrease of 26.4 kPa
  4. Increase of 118.3 kPa
Answer and working

A. Increase of 26.4 kPa

Before: σ′ = 19 × 10 − 9.81 × 10 = 91.9 kPa. After: σ = 18 × 3 + 19 × 7 = 187 kPa, u = 9.81 × 7 = 68.67 kPa, σ′ = 118.3 kPa. Change = +26.4 kPa. The answer 3γw = 29.4 ignores the small fall in total stress when the top 3 m drains. Lowering the water table raises effective stress, which is why drainage causes settlement.

Question 3 · medium

A clay liner for an on-farm water-harvesting pond must have the lowest possible permeability and resist cracking. Relative to the standard Proctor optimum, how should it normally be placed?

  1. Well dry of optimum, to give a flocculated structure
  2. At optimum with no compaction control
  3. Slightly wet of optimum, to give a dispersed structure
  4. Dry of optimum and then flooded
Answer and working

C. Slightly wet of optimum, to give a dispersed structure

Clay compacted wet of optimum has a dispersed particle arrangement with smaller continuous pores, so its permeability is lower, and it is more flexible. Dry of optimum the flocculated structure is stronger at placement but more permeable and more prone to swelling on wetting. Specifications set the actual range.

Question 4 · medium

A saturated clay (B = 1.0) has a pore-pressure parameter A = 0.5. Under undrained loading, σ3 increases by 50 kPa and σ1 increases by 150 kPa. What is the change in pore pressure?

  1. 75 kPa
  2. 100 kPa
  3. 150 kPa
  4. 50 kPa
Answer and working

B. 100 kPa

Δu = B[Δσ3 + A(Δσ1 − Δσ3)] = 1.0 × [50 + 0.5 × (150 − 50)] = 100 kPa. A multiplies the change in deviator stress (Δσ1 − Δσ3), not Δσ1 itself. 75 kPa applies A to Δσ1 alone (0.5 × 150).

Question 5 · medium

A drainage cut is excavated in a saturated, stiff overconsolidated clay. When is its stability usually most critical, and which analysis applies then?

  1. In the long term, with effective-stress parameters c′ and φ′
  2. Immediately after excavation, with cu and φ = 0
  3. During excavation only, with total-stress parameters
  4. It never changes because the clay is stiff
Answer and working

A. In the long term, with effective-stress parameters c′ and φ′

Excavation unloads the clay and creates negative excess pore pressures that dissipate slowly as water is drawn in. Effective stress and strength fall with time, so the long-term, drained case usually governs cuttings. For an embankment on soft clay the reverse is true: end of construction is critical.

Question 6 · hard

A dry soil slope at 30° has c′ = 10 kPa, φ′ = 25° and γ = 18 kN/m³. What is the factor of safety for sliding on a plane parallel to the surface 3 m deep (infinite-slope analysis)?

  1. 1.24
  2. 0.81
  3. 1.36
  4. 1.07
Answer and working

A. 1.24

Normal stress σ = γz cos²β = 18 × 3 × 0.75 = 40.5 kPa; shear stress τ = γz sinβ cosβ = 23.38 kPa. Strength = 10 + 40.5 × tan25° = 28.89 kPa. F = 28.89/23.38 = 1.24. tanφ/tanβ = 0.81 ignores cohesion; using cosβ instead of cos²β gives 1.36. 1.07 takes τ = γz sinβ without the cosβ (28.89/27.0).

Question 7 · medium

A 6 m high cutting in saturated clay (cu = 30 kPa, φu = 0, γ = 18 kN/m³) has a slope for which Taylor's chart gives a stability number cu/(FγH) = 0.18. What is the factor of safety?

  1. 0.65
  2. 0.28
  3. 1.54
  4. 9.26
Answer and working

C. 1.54

Sn = cu/(FγH), so F = cu/(Sn·γ·H) = 30/(0.18 × 18 × 6) = 30/19.44 = 1.54. 0.65 is the reciprocal. Some texts define the stability number the other way up, so always check the chart's definition. 0.28 stops at cu/(γH) = 30/108 without the stability number; 9.26 leaves out H (30/(0.18 × 18)).

Question 8 · hard

A slip circle through a dry embankment (c′ = 8 kPa, φ′ = 28°) is divided into four slices with weights 200, 400, 450 and 250 kN/m and base inclinations −5°, 15°, 35° and 55°. The total arc length is 18 m. By the ordinary (Fellenius) method of slices, what is the factor of safety?

  1. 1.06
  2. 1.33
  3. 1.25
  4. 0.75
Answer and working

B. 1.33

ΣW sinα = 200 × sin(-5°) + 400 × sin(15°) + 450 × sin(35°) + 250 × sin(55°) = 549.0 kN/m. ΣW cosα = 1097.6 kN/m. Resistance = c′L + ΣW cosα·tanφ′ = 8 × 18 + 1097.6 × 0.5317 = 727.6 kN/m. F = 727.6/549.0 = 1.33. The slice with negative α resists sliding, so its W sinα must stay negative; taking it as positive gives 1.25. Omitting cohesion gives 1.06. 0.75 is the ratio inverted (549.0/727.6).

Question 9 · hard

Why is Bishop's simplified method of slices generally preferred over the ordinary (Fellenius) method for effective-stress analysis of an earth dam with high pore pressures?

  1. It ignores all interslice forces, so it is conservative and therefore always the safer choice for dams with high pore pressures
  2. It includes horizontal interslice forces, and the ordinary method can underestimate F markedly when pore pressures are high
  3. It needs no iteration, unlike the ordinary method
  4. It applies only to φ = 0 analysis
Answer and working

B. It includes horizontal interslice forces, and the ordinary method can underestimate F markedly when pore pressures are high

The ordinary method ignores interslice forces, which makes the normal force on each slice base inaccurate, especially with high pore pressures and deep circles; it can give factors of safety well below more rigorous methods. Bishop's simplified method includes horizontal interslice forces and needs iteration because F appears on both sides.

Question 10 · hard

Why is Coulomb's wedge theory with a large wall friction angle not used for design passive resistance?

  1. The assumed plane failure surface overestimates passive resistance, which is unsafe; curved log-spiral surfaces give lower values
  2. It underestimates passive resistance (too low a Kp), which is too conservative
  3. It cannot include wall friction, so the roughness of the wall back is ignored
  4. It is valid only for cohesive soils and gives no solution for clean sands
Answer and working

A. The assumed plane failure surface overestimates passive resistance, which is unsafe; curved log-spiral surfaces give lower values

With significant wall friction the true passive failure surface is curved. A plane surface is not the critical one and gives passive coefficients that are too high, i.e. unsafe. Log-spiral solutions or charts based on them are used instead.

A study plan for Soil Mechanics in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 36 questions): Seepage and flow nets (7, 19%); Slope stability, including infinite slopes (7, 19%); Shear strength and the Mohr-Coulomb criterion (5, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Terzaghi one-dimensional consolidation (4, 11%); Bearing capacity basics (3, 8%); Effective stress (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Permeability (3, 8%); Compaction and the Proctor test (2, 6%); Earth pressure: active and passive (Rankine) (2, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Bearing capacity basics (3 hard of 3), Effective stress (3 hard of 3), Permeability (3 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Soil Mechanics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.