LAISHA
Open Laisha

ICAR AICE-JRF/SRF Soil Mechanics: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
61written to this exam in this subject
11syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Soil Mechanics in ICAR AICE-JRF/SRF

Deeper treatment of seepage through and under earth dams (phreatic line, filters, piping), consolidation theory and its assumptions, drained versus undrained analysis, stability cases for earth dams including rapid drawdown, and methods of slices.

Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.

Our 61 ICAR AICE-JRF/SRF questions in this subject: 3 easy, 30 medium, 28 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

A soil pat dried below its shrinkage limit has a shrinkage ratio of 1.85. The specific gravity of solids is 2.70. What is the shrinkage limit?

  1. 54.1%
  2. 17.0%
  3. 37.0%
  4. 31.5%
Answer and working

B. 17.0%

ws = 1/R − 1/G = 1/1.85 − 1/2.70 = 0.5405 − 0.3704 = 17.0%. The shrinkage ratio R is the dry density of the pat divided by the density of water, so 1/R is the volume of dry pat per unit mass of solids and 1/G the volume of solids; their difference is the void volume, filled with water at the shrinkage limit. 54.1% is 1/R alone, 37.0% is 1/G alone, and 31.5% is (G − R)/G = 0.85/2.70.

Question 2 · hard

A well fully penetrating an unconfined aquifer is pumped at a steady 0.012 m³/s. In observation wells at 15 m and 60 m from it, the water table stands 9.0 m and 10.0 m above the impermeable base. What is k?

  1. 2.79e-04 m/s
  2. 1.21e-04 m/s
  3. 5.30e-03 m/s
  4. 8.76e-04 m/s
Answer and working

A. 2.79e-04 m/s

k = q·ln(r2/r1)/[π(h2² − h1²)] = 0.012 × ln 4/[π(100 − 81)] = 0.01664/59.69 = 2.79e-04 m/s. Using log10 without conversion gives 1.21e-04; using (h2 − h1) instead of (h2² − h1²) gives 5.30e-03 and confuses it with the confined-aquifer formula.

Question 3 · hard

A well in a confined aquifer 12 m thick is pumped at 0.02 m³/s. The piezometric heads in observation wells at 10 m and 50 m differ by 0.9 m. What is k?

  1. 4.74e-04 m/s
  2. 2.06e-04 m/s
  3. 9.49e-04 m/s
  4. 5.69e-03 m/s
Answer and working

A. 4.74e-04 m/s

k = q·ln(r2/r1)/[2πb(h2 − h1)] = 0.02 × ln 5/(2π × 12 × 0.9) = 0.03219/67.86 = 4.74e-04 m/s. Omitting the factor 2 gives 9.49e-04; omitting the aquifer thickness b gives 5.69e-03.

Question 4 · hard

Downstream of a weir, the last square of a flow net has a length of 1.2 m along the flow line. The total head loss of 6 m is spread over 12 equal equipotential drops. The foundation sand has G = 2.68 and e = 0.72. What is the factor of safety against boiling at the exit?

  1. 2.34
  2. 0.20
  3. 3.74
  4. 0.43
Answer and working

A. 2.34

Head drop per equipotential = 6/12 = 0.5 m. Exit gradient = 0.5/1.2 = 0.417. ic = (G − 1)/(1 + e) = 0.977. FS = ic/iexit = 2.34. Using the whole head over one square (5.0) gives 0.20; 0.43 is the ratio upside down. A factor near 2.3 is below the 3 to 4 usually wanted, so the exit needs a loaded filter. 3.74 computes ic as G/(1 + e) = 1.558, forgetting buoyancy (1.558/0.417).

Question 5 · easy

Laplace's equation for two-dimensional seepage does NOT assume which of the following?

  1. Turbulent flow
  2. Darcy's law is valid
  3. The soil is saturated
  4. Soil and water are incompressible
Answer and working

A. Turbulent flow

Laplace's equation follows from continuity plus Darcy's law, which is valid for laminar flow. It assumes a saturated, homogeneous, isotropic soil with incompressible soil and water. Turbulent flow would violate Darcy's law.

Question 6 · hard

A clay has k = 1 × 10⁻⁹ m/s and mv = 0.25 m²/MN. With γw = 9.81 kN/m³, what is its coefficient of consolidation in m²/year?

  1. 0.0129 m²/year
  2. 126 m²/year
  3. 12.9 m²/year
  4. 1.29 m²/year
Answer and working

C. 12.9 m²/year

mv = 0.25 m²/MN = 2.5 × 10⁻⁴ m²/kN. cv = k/(mv·γw) = 10⁻⁹/(2.5 × 10⁻⁴ × 9.81) = 4.077e-07 m²/s × 3.156 × 10⁷ s/year = 12.9 m²/year. Using 0.25 as if in m²/kN gives 0.0129; omitting γw gives 126. 1.29 is a factor-of-ten slip in the unit conversion.

Question 7 · hard

A clay layer 3 m thick (e0 = 0.90) has σ′0 = 80 kPa and a preconsolidation pressure of 150 kPa at mid-depth. Cc = 0.30 and Cr = 0.05. What settlement results from a stress increase of 50 kPa at mid-depth?

  1. 99.9 mm
  2. 16.6 mm
  3. 31.6 mm
  4. 38.3 mm
Answer and working

B. 16.6 mm

Final stress 80 + 50 = 130 kPa is below σ′p = 150 kPa, so only recompression occurs: S = [Cr·H/(1 + e0)]·log(130/80) = (0.05 × 3/1.90) × 0.2109 = 16.6 mm. Using Cc treats the clay as normally consolidated and gives 99.9 mm, about six times too much; leaving out (1 + e0) gives 31.6 mm. OCR = 150/80 = 1.88. 38.3 mm uses the natural logarithm instead of log10 (0.0789 × ln 1.625).

Question 8 · easy

Which of the following is NOT an assumption of Terzaghi's one-dimensional consolidation theory?

  1. Flow and compression are one-dimensional
  2. Darcy's law is valid
  3. Soil grains and water are incompressible
  4. The soil is partly saturated with compressible pore air
Answer and working

D. The soil is partly saturated with compressible pore air

Terzaghi's theory assumes a fully saturated, homogeneous soil with incompressible grains and water, one-dimensional flow and strain, Darcy's law and constant k and mv over the load increment. Pore air would make the pore fluid compressible and is outside the theory.

Question 9 · medium

A soil has c′ = 10 kPa and φ′ = 25°. In a drained triaxial test at a cell pressure of 150 kPa, what major principal effective stress will cause failure?

  1. 369.6 kPa
  2. 401.0 kPa
  3. 418.9 kPa
  4. 385.3 kPa
Answer and working

B. 401.0 kPa

σ′1 = σ′3·tan²(45° + φ′/2) + 2c′·tan(45° + φ′/2). tan 57.5° = 1.5697, tan² = 2.4639. σ′1 = 150 × 2.4639 + 2 × 10 × 1.5697 = 369.6 + 31.4 = 401.0 kPa. Leaving out cohesion gives 369.6; the cohesion term uses tan(45° + φ′/2), not its square. 418.9 kPa squares the tangent in the cohesion term (369.6 + 2 × 10 × 2.4639); 385.3 kPa leaves out the 2 (369.6 + 10 × 1.5697).

Question 10 · medium

A vertical cut is made in a saturated clay with cu = 25 kPa, φu = 0 and γ = 18 kN/m³. By Rankine's theory, what is the depth of tension cracks and the critical unsupported height?

  1. Crack depth 1.39 m; critical height 2.78 m
  2. Crack depth 2.78 m; critical height 2.78 m
  3. Crack depth 5.56 m; critical height 11.11 m
  4. Crack depth 2.78 m; critical height 5.56 m
Answer and working

D. Crack depth 2.78 m; critical height 5.56 m

With φu = 0, Ka = 1. zc = 2cu/γ = 50/18 = 2.78 m. The net active thrust is zero at depth 2zc, so Hc = 4cu/γ = 5.56 m. In practice cracks fill with water and cuts are supported well below this height; Taylor's circular analysis gives a lower value near 3.85cu/γ.

A study plan for Soil Mechanics in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 61 questions): Seepage and flow nets (8, 13%); Shear strength and the Mohr-Coulomb criterion (8, 13%); Slope stability, including infinite slopes (8, 13%); Terzaghi one-dimensional consolidation (8, 13%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Bearing capacity basics (7, 11%); Earth pressure: active and passive (Rankine) (6, 10%); Permeability (5, 8%); Effective stress (4, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Index properties and soil classification (3, 5%); Compaction and the Proctor test (2, 3%); Phase relations (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Effective stress (4 hard of 4), Index properties and soil classification (2 hard of 3), Permeability (3 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Seepage and flow nets (1 easy of 8); Shear strength and the Mohr-Coulomb criterion (1 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Soil Mechanics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.