LAISHA
Open Laisha

ICAR AICE-JRF/SRF Renewable Energy Sources (Solar, Wind): practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
68written to this exam in this subject
14syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Renewable Energy Sources (Solar, Wind) in ICAR AICE-JRF/SRF

Units 4 (solar), 5 (wind) and 7 (power generation and storage) at PG depth: Hottel–Whillier–Bliss analysis, concentration limits, diode model and MPPT algorithms, Weibull wind statistics, capacity factor, battery sizing and storage options, and energy economics.

Solar thermal, solar PV, wind and micro-hydro for farms, from sun geometry to sizing a solar pump.

Our 68 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 45 medium, 22 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A flat-plate collector has FR(τα) = 0.75 and FRUL = 5 W/m²K. At an irradiance of 800 W/m², with inlet water 20 K above ambient, what is its instantaneous efficiency?

  1. 0.625
  2. 0.750
  3. 0.650
  4. 0.656
Answer and working

A. 0.625

η = FR(τα) − FRUL(Ti − Ta)/G = 0.75 − 5 × 20/800 = 0.75 − 0.125 = 0.625. 0.750 is the optical efficiency with no loss; using 1000 W/m² gives 0.650; multiplying the terms gives 0.656.

Question 2 · medium

On a plot of flat-plate collector efficiency against (Ti − Ta)/G, the intercept and slope of the Hottel–Whillier–Bliss line are respectively:

  1. FRUL and −FR(τα)
  2. (τα) and −UL
  3. F′ and −FR
  4. FR(τα) and −FRUL
Answer and working

D. FR(τα) and −FRUL

η = FR(τα) − FRUL(Ti − Ta)/G, so the intercept is FR(τα) (optical efficiency) and the slope −FRUL. Writing (τα) and UL without FR would apply only if the whole plate were at inlet temperature with perfect heat removal.

Question 3 · medium

Silicon has a band gap of 1.12 eV. What is the longest wavelength of light that can create an electron–hole pair in it?

  1. 1107 nm
  2. 1389 nm
  3. 1.11 nm
  4. 550 nm
Answer and working

A. 1107 nm

λmax = hc/Eg = 1240 (eV·nm)/1.12 eV = 1107 nm. Photons of longer wavelength have too little energy and pass through unused. Multiplying instead of dividing gives 1389 nm; 550 nm is the middle of the visible band, not a cut-off. 1.11 nm uses hc = 1.24 instead of 1240 eV·nm.

Question 4 · medium

For a deep borehole requiring low flow at high head, which pump type keeps the best efficiency over the varying speed of a solar pump drive?

  1. A helical-rotor positive-displacement submersible pump
  2. A single-stage surface centrifugal pump
  3. An axial-flow propeller pump
  4. An air-lift pump
Answer and working

A. A helical-rotor positive-displacement submersible pump

Positive-displacement pumps deliver flow roughly proportional to speed at any head and keep good efficiency at low speed, suiting weak morning sun and high heads. Centrifugal and axial-flow pumps suit high flow at low head and lose output sharply when speed drops; a surface pump cannot lift from deep boreholes.

Question 5 · medium

What is the density of dry air at 101.325 kPa and 30 °C? (R = 287 J/kg K)

  1. 11.8 kg/m³
  2. 1.225 kg/m³
  3. 1.165 kg/m³
  4. 0.00117 kg/m³
Answer and working

C. 1.165 kg/m³

ρ = p/(RT) = 101325/(287 × 303.15) = 1.165 kg/m³ (≈ 1.165 with T = 303 K). Using 30 in Celsius gives 11.8; 1.225 is the 15 °C sea-level value; using kPa gives a result 1000 times too small. Warm air carries about 5% less power than the standard value at the same speed.

Question 6 · medium

A three-bladed rotor of 20 m radius turns at 30 rpm in a 10 m/s wind. What is its tip speed ratio?

  1. 60
  2. 6.28
  3. 3.14
  4. 377
Answer and working

B. 6.28

ω = 2πN/60 = 2π × 30/60 = 3.142 rad/s; tip speed = ωR = 62.8 m/s; λ = ωR/V = 6.28. Using rpm directly gives 60; taking the radius as 10 m (half its true value) halves it to 3.14; forgetting /60 gives 377.

Question 7 · medium

The Savonius rotor differs from the Darrieus rotor in that the Savonius is:

  1. A drag-driven vertical-axis rotor with high starting torque but low power coefficient
  2. A lift-driven horizontal-axis rotor with very high tip speed ratio and a low starting torque
  3. A lift-driven vertical-axis rotor that cannot self-start
  4. A type of multi-blade horizontal-axis windmill
Answer and working

A. A drag-driven vertical-axis rotor with high starting torque but low power coefficient

The Savonius (S-shaped half-cylinders) works mainly by drag, starts easily and runs slowly with low Cp. The Darrieus uses aerofoil blades and lift, reaching higher Cp, but often needs help to start. Both are vertical-axis machines.

Question 8 · medium

Why is the solar declination zero at the equinoxes?

  1. The earth is then at perihelion, closest to the sun, so its rays strike the whole globe at the same angle
  2. The earth's axis is then perpendicular to its orbit
  3. The sun's rays are then parallel to the equatorial plane, so the noon sun is overhead at the equator
  4. Day length at the poles is then 24 hours
Answer and working

C. The sun's rays are then parallel to the equatorial plane, so the noon sun is overhead at the equator

Declination is the angle between the sun–earth line and the equatorial plane; at the equinoxes this line lies in the equatorial plane. The earth's axial tilt does not change, and perihelion occurs in early January, not at an equinox.

Question 9 · hard

The collector heat removal factor FR increases when:

  1. The overall loss coefficient UL increases, because the plate then passes more of its heat to the fluid rather than the air
  2. The fluid mass flow rate increases, because the fluid temperature rise and hence the mean plate temperature fall
  3. The fluid flow rate decreases to near zero
  4. The collector is operated at stagnation
Answer and working

B. The fluid mass flow rate increases, because the fluid temperature rise and hence the mean plate temperature fall

FR = (ṁcp/AcUL)[1 − exp(−AcULF′/ṁcp)] rises towards F′ as ṁ increases, because the plate runs closer to inlet temperature. It falls towards zero as flow goes to zero (stagnation). A higher UL lowers FR.

Question 10 · medium

In agricultural energy auditing, energy used to manufacture fertiliser and machinery is classified as:

  1. Direct energy input on the farm
  2. Renewable energy output
  3. Indirect energy input
  4. Useful end-use energy output
Answer and working

C. Indirect energy input

Direct energy is used on the farm itself (diesel, electricity, human and animal labour); energy embodied in manufactured inputs such as fertiliser, pesticides and machinery is indirect. The coefficients used to value them come from a cited table and differ between sources.

A study plan for Renewable Energy Sources (Solar, Wind) in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 68 questions): Energy storage (7, 10%); Concentrating collectors (6, 9%); Flat-plate collectors and their efficiency (6, 9%); Measurement of solar radiation (6, 9%); Photovoltaic cell physics and the I-V curve (6, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Power in the wind and the Betz limit (6, 9%); Solar radiation geometry (6, 9%); Fill factor and MPPT (5, 7%); Wind turbines and water-pumping windmills (5, 7%); PV system sizing: on-grid and off-grid (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Solar dryers, cookers, water heaters and stills (4, 6%); Solar pumps and agri-voltaics (3, 4%); Energy scenario (2, 3%); Micro-hydro (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Photovoltaic cell physics and the I-V curve (3 hard of 6), Solar radiation geometry (3 hard of 6), PV system sizing: on-grid and off-grid (2 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Energy storage (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Renewable Energy Sources (Solar, Wind)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.