LAISHA
Open Laisha

ICAR AICE-JRF/SRF Farm Machinery Testing, Evaluation & Standards: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
52written to this exam in this subject
12syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Testing, Evaluation & Standards in ICAR AICE-JRF/SRF

Test procedure detail: lug curve and torque backup, drawbar test on track versus field, hydraulic lift through the range, static versus dynamic ROPS, noise and vibration evaluation, implement test indices (miss, multiple, quality of feed), and interpretation of test reports.

How tractors and implements are tested against codes, and how to read a test report.

Our 52 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 33 medium, 19 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A national tractor testing station wants formal recognition that its laboratories are technically competent to produce valid results. The international standard it is accredited to is

  1. ISO 9001, quality management systems for any organisation that designs or makes products
  2. ISO 14001, environmental management systems for sites that handle fuels and lubricants
  3. ISO/IEC 17025, competence of testing and calibration laboratories
  4. ISO 4254-1, general safety requirements for agricultural machinery used on the farm
Answer and working

C. ISO/IEC 17025, competence of testing and calibration laboratories

Laboratory competence, including calibration traceability and measurement uncertainty, is covered by ISO/IEC 17025. ISO 9001 is a general quality management standard, ISO 14001 environmental management, and ISO 4254-1 a machinery safety standard, none of which accredits a testing laboratory's results.

Question 2 · medium

OECD Codes 6 and 7 apply to

  1. dynamic and static ROPS testing of standard wide-track wheeled tractors
  2. protective structures fitted to track-laying tractors used in forestry
  3. front-mounted and rear-mounted ROPS on narrow-track wheeled tractors
  4. noise and vibration at the seat of tractors with closed operator cabs
Answer and working

C. front-mounted and rear-mounted ROPS on narrow-track wheeled tractors

Codes 6 and 7 cover the roll bars of narrow-track tractors used in orchards and vineyards, front-mounted and rear-mounted respectively. Codes 3 and 4 are the dynamic and static tests for standard tractors, Code 8 covers track-layers, and Code 5 covers noise.

Question 3 · hard

Report X gives a tractor's maximum PTO power measured under a national code; report Y gives another tractor's maximum PTO power under the OECD code. Before comparing the two numbers directly, the main thing to establish is

  1. whether both stations used the same make of dynamometer, since makes always read differently
  2. whether both tractors carry the same paint and badge, since appearance shows the engine fitted
  3. whether both reports were printed in the same year, since older reports always overstate power
  4. whether both codes define test conditions alike, as load steps and limits are code-specific
Answer and working

D. whether both codes define test conditions alike, as load steps and limits are code-specific

Two codes may define rated speed, test duration, permitted adjustments, atmospheric corrections and reported quantities differently, so the same tractor can give different numbers under each. A calibrated dynamometer of any make should give the same reading, and the year of a report does not by itself bias it.

Question 4 · medium

With no drawbar load a tractor advances 4.2 m per revolution of its driving wheels. Under a heavy load it advances 3.6 m per revolution. The wheel slip is

  1. 16.7 %
  2. 85.7 %
  3. 6.0 %
  4. 14.3 %
Answer and working

D. 14.3 %

Slip = (advance unloaded − advance loaded)/advance unloaded × 100 = (4.2 − 3.6)/4.2 × 100 = 14.3 %. Dividing by the loaded advance gives 16.7 %; 85.7 % is the travel ratio; 6.0 simply scales the difference.

Question 5 · medium

In a tractor drawbar test, maximum drawbar pull is normally obtained in the lowest gears while maximum drawbar power is obtained in a middle gear. The reason maximum pull is found in low gears is that

  1. pull there is limited by wheel slip before the engine reaches full power
  2. the governor cuts fuel in low gears so the engine never reaches rated speed
  3. rolling resistance vanishes at low speed so all axle power becomes pull
  4. the code requires the load car to brake hardest whenever speed is lowest
Answer and working

A. pull there is limited by wheel slip before the engine reaches full power

In low gears the high gear reduction can produce more axle torque than the tyres can transmit; the slip limit stops the run first. In middle gears the engine reaches maximum power at a useful speed, so drawbar power peaks there. Rolling resistance does not vanish at low speed, and the governor does not cut fuel by gear.

Question 6 · medium

A gear pump of displacement 18 cm³/rev runs at 2000 rev/min. At the test pressure the measured delivery is 32.4 L/min. The volumetric efficiency is

  1. 90 %
  2. 180 %
  3. 111 %
  4. 1.5 %
Answer and working

A. 90 %

Theoretical delivery = 18 × 2000/1000 = 36 L/min. Volumetric efficiency = 32.4/36 = 90 %. 111 % is the inverse; 180 % divides by displacement without speed; 1.5 % mixes per-second and per-minute flow.

Question 7 · medium

Three independent sources produce 84, 87 and 90 dB(A) at the driver's position. The combined level is

  1. 87.0 dB(A)
  2. 90.0 dB(A)
  3. 261.0 dB(A)
  4. 92.4 dB(A)
Answer and working

D. 92.4 dB(A)

L = 10 log₁₀(10^8.4 + 10^8.7 + 10^9.0) = 10 log₁₀(2.512e+08 + 5.012e+08 + 1.000e+09) = 92.4 dB(A). The arithmetic mean (87.0) and the loudest source alone (90) both ignore the added energy; the plain sum is meaningless.

Question 8 · medium

During a static ROPS test, which observation alone is enough for the structure to fail?

  1. The structure bends permanently by a visible amount after loading
  2. The paint on the structure cracks and flakes at the welded joints
  3. The structure takes more than one minute to reach the required energy
  4. Any part of the structure enters the operator's clearance zone during loading
Answer and working

D. Any part of the structure enters the operator's clearance zone during loading

A ROPS is meant to deform and absorb energy, so permanent bending is expected; failure is entry into the clearance zone, or fracture or mounting failure. Paint cracking and loading time are not acceptance criteria.

Question 9 · hard

In the OECD ROPS codes, the energies to be absorbed and the crushing forces are set as functions of the tractor's reference mass. The reason is that

  1. a heavier tractor is less likely to overturn, so its structure can be weaker
  2. the reference mass sets the size of the cab, which sets the clearance zone
  3. a heavier tractor has a larger engine, which must be protected by the ROPS
  4. a heavier tractor carries more energy in an overturn and loads its structure more
Answer and working

D. a heavier tractor carries more energy in an overturn and loads its structure more

The energy released in an overturn and the load on the structure when it supports the tractor scale with mass, so required energies and crushing forces rise with reference mass. The clearance zone is set from the seat, not cab size, and the ROPS protects the operator, not the engine.

Question 10 · medium

Two tractor test reports give specific fuel consumption: tractor A 245 g/kWh at maximum power, tractor B 265 g/kWh at 50 per cent load. Before concluding that A is more efficient, the reader should

  1. compare both at the same load, since SFC rises as the load falls
  2. convert both to L/h, since g/kWh cannot be compared between tractors
  3. add 20 g/kWh to A, since maximum-power runs are always over-corrected
  4. ignore load, since SFC depends only on the engine's rated speed
Answer and working

A. compare both at the same load, since SFC rises as the load falls

SFC is normally higher at part load, so B's figure at 50 per cent load cannot be compared with A's at full load. The reports give both tractors at several loads; compare like with like. g/kWh is the right comparative unit, and there is no standard correction of the kind in the other statements.

A study plan for Farm Machinery Testing, Evaluation & Standards in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 52 questions): Drawbar performance test (6, 12%); Hydraulic lift test (6, 12%); Interpreting test reports (5, 10%); Noise at the operator's ear (5, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: PTO performance test (5, 10%); ROPS and FOPS tests (5, 10%); Test instrumentation: dynamometers and fuel meters (5, 10%); Laboratory and field tests of tillage and sowing equipment (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (3, 6%); Tests of sprayers and harvesting equipment (3, 6%); Types of tests: commercial, batch, confidential and prototype (3, 6%); Brake and turning tests (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: PTO performance test (3 hard of 5), Brake and turning tests (1 hard of 2), Interpreting test reports (2 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Farm Machinery Testing, Evaluation & Standards

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.